Samson AirLine Manuel utilisateur

UHF Wireless System

Owners Manual

• AF1 Instrument Transmitter

• AG1 Instrument Transmitter

• AP1 Receiver

• UR1 Receiver

SAMSON

ENGLISH

Introduction 1

QuickStart 2

Guided Tour - AP1 Receiver 4

Guided Tour - UR1 Receiver 7

Guided Tour - AF1 / AG1 Transmitter 10

Setting Up and Using Your AirLine System 12

Specifications 57

Channel Plan 59

FRANCAIS

Introduction 15

Prise en main 16

Visite guidée – Récepteur AP1 18

Visite guidée – Récepteur UR1 21

Visite guidée – Emetteur AF1 / AG1 24

Configuration et utilisation du système AirLine 26

Spécifications 57

Tableau de conversion de fréquence 59

Samson Technologies Corp.

575 Underhill Blvd.

P.O. Box 9031

Syosset, NY 11791-9031

Phone: 1-800-3-SAMSON (1-800-372-6766)

Fax: 516-364-3888

www.samsontech.com

Table of Contents

Produced by On The Right Wavelength for Samson Technologies Corp.

Reprinted April 2001

DEUTSCHE

Einleitung 29

Schneller Einstieg 30

Übersicht - Empfänger AP1 32

Übersicht - Empfänger UR1 35

Übersicht - Sender AF1 / AG1 38

AirLine System einrichten und einsetzen 40

Technische Daten 57

Frequenzzuordnung der Empfangskanäle 59

ESPANOL

Introducción 43

Arranque rápido 44

Recorrido guiado – Receptor AP1 46

Recorrido guiado – Receptor UR1 49

Recorrido guiado – Transmisor AF1 / AG1 52

Ajuste y uso de su sistema AirLine 54

Especificaciones 57

Tabla de conversión de frecuencias 59

Note: All trademarks are the property of their respective holders

Samson AirLine

Welcome to Samson AirLine—the wireless system for the new millennium! Wireless microphone and instrument systems were

originally developed to eliminate cables, providing unparalleled freedom of movement. AirLine takes this concept to a new level with

transmitters so small, lightweight and aerodynamic, they are nearly invisible, providing a completely “hassle-free” user experience.

To create the world’s smallest wireless transmitters, we developed new proprietary technology. Featuring miniaturized circuitry and the

ability to operate on a single tiny AAA battery (with 14 hours typical battery life), these transmitters also provide significantly improved

wireless reception and sound quality. What’s more, the AP1 receiver developed especially for the AirLine guitar system is actually

smaller than the typical wireless transmitter.

The Samson AirLine UHF guitar system detailed in this manual is designed to replace the cable between your electric guitar or bass

and your onstage amplifier or PA mixer, freeing you to roam the stage or even visit the audience in the middle of your performance!

It operates in the uncrowded 801 - 805 MHz UHF frequency range and contains an AP1 “stomp box”-style receiver and either of two

plug-in micro-transmitter models—an AF1 (designed to fit the recessed style jack in Fender Stratocaster™-type guitars) or an AG1

(which fits all other standard end-mount guitar jacks).

In this manual, you’ll find a more detailed description of the features of your AirLine system, as well as a guided tour through all

components, step-by-step instructions for setting up and using your system and full specifications. If your AirLine system was

purchased in the United States, you’ll also find a warranty card enclosed—don’t forget to fill it out and mail it! This will enable you to

receive online technical support and will allow us to send you updated information about this and other Samson products in the

future. If your AirLine system was purchased outside of the U. S., contact your local distributor for warranty details. Also, be sure to

check out our website (http://www.samsontech.com) for complete information about our full product line.

SPECIAL NOTE for U.S. purchasers: Should your AirLine system ever require servicing, a Return Authorization number (RA) is

necessary. Without this number, the unit will not be accepted. If your AirLine system was purchased in the United States, please call

Samson at 1-800-372-6766 for a Return Authorization number prior to shipping your system. If possible, return the unit in its original

carton and packing materials. If your AirLine system was purchased outside of the U. S., contact your local distributor for information.

Samson AirLine

Introduction

ENGLISH

If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your

AirLine UHF guitar system in a matter of minutes! Detailed instructions for setting up and using your AirLine system can be found on

page 9 of this manual, and the “Guided Tour” sections on pages 4 - 8 provide full descriptions of all AirLine component controls and

displays.

1. Make sure that the supplied AP1 receiver and AF1 or AG1 transmitter are factory preset to the same channel.

2. Physically place the AP1 receiver on the ground in front of you. Extend its antennas vertically and spread the tips horizontally out-

wards approximately 5 inches.

3. Set the power switch on your AF1 or AG1 transmitter to the “off” position (away from the arrow) and place a fresh AAA battery in it.

Then turn the transmitter back on momentarily; its LED will flash once and then go off if the battery is sufficiently strong. Once

battery strength is verified, turn the transmitter off again, then plug it into your electric guitar or bass.

4. Open the battery compartment of the AP1 by pressing on the latch and install a fresh battery; if you prefer, you can use an optional

power supply instead. Turn the AP1 on momentarily to confirm that the battery has been installed correctly (or that the adapter has

been connected correctly); the “On/Battery Low” LED should light green and not red. Then turn the AP1 power off.

5. Turn your amplifier or mixer off and make the physical cable connection between an audio input and the AP1 output jack.

6. Turn the Level knob on the AP1 completely counterclockwise, then turn its power on; the “Power” LED will light steadily green.

7. Turn on your AF1 or AG1 transmitter. The “TX/Peak” LED on the AP1 receiver should light steadily green, indicating that it is

receiving valid RF signal and is placed and positioned correctly.

Samson AirLine QuickStart

ENGLISH

8. Turn on the connected amplifier or mixer but keep its volume all the way down. Set the output level of your instrument to max-

imum and begin playing at a normal performance level while observing the AP1 “TX/Peak” LED. If the LED lights red (indicating a

Peak condition) even with the AP1 Level control fully counterclockwise, engage the 15 dB pad on the transmitter. If not, slowly turn

the Level control clockwise to the point where the “TX/Peak” LED occasionally blinks red during the very loudest passages, then back

it off just slightly. Finally, raise the level of your connected amplifier and/or mixer until the desired volume is reached.

9. Do a walkaround through the intended area of coverage while observing the receiver’s “TX/Peak” LED; it should continue to be lit

steadily green, indicating sufficient RF reception in all areas of coverage. If not, reposition the AP1 or its antennas as necessary.

10. If you hear any spurious noise from the receiver output when the transmitter is turned off, use the supplied plastic screwdriver to

adjust the AP1 Squelch control, slowly turning it clockwise to the point at which the noise disappears.

Samson AirLine

QuickStart

ENGLISH

1: Power switch - Move this switch in the direction of the arrow to turn

power to the AP1 on; move it away from the arrow to turn power off. (A

jack must be inserted into the input connector for the receiver to power up.)

2: Power On / Battery Low LED - This LED lights green whenever the

AP1 is powered on and it lights red whenever the battery in the AP1 is

running low. In order to avoid compromising audio fidelity (or having

the AP1 stop working completely), you should always replace the

battery with a fresh one immediately whenever this LED lights red.

3: TX / Peak LED - This LED lights green whenever the AP1 is receiving

RF signal from a transmitter and it lights red when output signal from

the AP1 is at the onset of clipping (that is, when it is on the verge of

being distorted). If you see this light during operation, lower the

volume level of your instrument or switch on the transmitter’s 15 dB

pad. For more information, see the section entitled “Setting Up and

Using Your AirLine System” on page 9 in this manual.

4: Level control - This knob sets the level of the audio signal being

output through the AP1 output jack (see #9 on page 6). When using an

electric guitar or bass with an active or high-level pickup, set the knob

in the marked area. For more information, see the section entitled

“Setting Up and Using Your AirLine System” on page 9 in this manual.

Samson AirLine Guided Tour - AP1 Receiver

ENGLISH

OPEN

AP1

UHF RECEIVER

LEVEL

POWER

∞

•

BATT. LOW

PEAK

2 3

5: Antennas - Swivel mounting allows full rotation for optimum positioning of the

dual AP1 antennas. In normal operation, extend both antennas vertically and

spread the tips horizontally outwards approximately 5 inches. For convenience,

they can be folded inward when transporting the AP1. See the “Setting Up and

Using Your AirLine System” section on page 9 in this manual for more information

about antenna positioning.

6: Battery compartment latch - Press gently on this latch to open the AP1 battery

compartment (see #7 below).

7: Battery compartment - Insert a standard 9-volt alkaline battery here, being sure

to observe the plus and minus polarity markings shown. We recommend the

Duracell MN 1604 type battery. Although rechargeable Ni-Cad batteries can be

used, they do not supply adequate current for more than four hours.

WARNING: Do not insert the battery backwards; doing so can cause severe

damage to the AP1 and will void your warranty. Note that the AP1 can also be AC

powered with the use of an optional 12 volt adapter available from your Samson

dealer (see #10 on the following page).

8: Plastic screwdriver - Specially designed for use in adjusting the AP1 Squelch

control (see #11 on the following page). See the “Setting Up and Using Your

AirLine System” section on page 9 in this manual for more information.

Samson AirLine

Guided Tour - AP1 Receiver

ENGLISH

AP1

UHF RECEIVER

LEVEL

POWER

∞

•

BATT.LOW

PEAK

SAMSON

Guided Tour - AP1 Receiver

Samson AirLine

9: Output jack - Use this standard unbalanced high

impedance (5 - 10 K Ohm) 1/4" jack to connect the AP1 to

your amplifier or audio mixer. Wiring is as follows: tip hot,

sleeve ground.

10: DC input - Connect an optional 12 volt 200 mA power

adapter (available from your Samson dealer) here.

WARNING: Do not substitute any other kind of power

adapter; doing so can cause severe damage to the AP1 and

will void your warranty. Note that the AP1 can also be

battery powered (see #7 on the previous page and the

“Setting Up and Using Your AirLine System” section on page

9 in this manual).

11: Squelch control - This control determines the maximum

range of the AP1 before audio signal dropout. Although it

can be adjusted using the supplied plastic screwdriver, it

should normally be left at its factory setting. See the “Setting

Up and Using Your AirLine System” section on page 9 in this

manual for more information.

ENGLISH

DC INPUT

12 VDC

SQUELCH

MIN MAX

OUTPUT

1: Antennas (A and B) - The

antenna mountings allow full

rotation for optimum placement.

In normal operation, both Antenna

A (the antenna on the left) and

Antenna B (the antenna on the

right) should be placed in a vertical

position. Both antennas can be

folded inward for convenience

when transporting the UR1. See

the “Setting Up and Using the

AirLine System” section on page

16 in this manual for information

about antenna installation and

positioning.

2: AF (Audio Frequency) Level control - This knob sets the level of the audio signal being output through both the balanced and

unbalanced output jacks on the rear panel (see #2 and #4 on page 8 in this manual). Reference level is obtained when the knob is

turned fully clockwise (to its “10” setting).

3: Peak LED - This LED lights yellow when output signal from the UR1 is at the onset of clipping (that is, when it is on the verge of

being distorted). If you see this light during operation, move the microphone further away or lower the output level of your

instrument or transmitter. For more information, see the section entitled “Setting Up and Using the AirLine System” on page 16 in

this manual.

Guided Tour - UR1 Receiver / Front Panel

SAMSON

UHF RECEIVER

351

446

Samson AirLine

ENGLISH

Samson AirLine

4: A/B Receiver LEDs - When signal is being received, one of these will be lit green, showing you whether the (left) “A” or (right) “B”

receiver is currently being used. The UR1 constantly scans its two antennas and automatically selects whichever is receiving the

strongest, clearest signal. This True Diversity switching is completely inaudible, but it effectively increases overall range while

virtually eliminating potential interference and phase cancellation problems.

5: RF (Radio Frequency) Level meter - This five-segment meter (similar to the VU bar meter used on audio devices) indicates the

strength of the UHF signal being received. When all segments are lit, the incoming RF signal is at optimum strength; when only the

left-most segment is lit, the incoming RF signal is at minimum strength. If no segments are lit, no signal is being received; check to

ensure that the transmitter is on and that it is set to the same channel as the UR1. See the “Setting Up and Using the AirLine System”

section on page 16 in this manual for more information.

6: Power LED - This lights red whenever the UR1 is turned on.

7: Mute (squelch) control - This control determines the maximum range of the UR1 before audio signal dropout. Although it can be

adjusted using the supplied plastic screwdriver, it should normally be left at its factory setting. See the “Setting Up and Using the

AirLine System” section on page 16 in this manual for more information.

8: Power switch - Use this to turn the UR1 power on and off. When the receiver is on, the Power LED (see #6 above) is lit.

Guided Tour - UR1 Receiver / Front Panel

ENGLISH

Autres manuels pour AirLine

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Samson Système de microphone

Samson

Samson XPD2 Manuel utilisateur

Samson

Samson XPDm Manuel utilisateur

Samson

Samson CB88 Manuel utilisateur

Samson

Samson AirLine 77 AH1N Manuel utilisateur

Samson

Samson UHF Series One Manuel utilisateur

Samson

Samson AirLine Manuel utilisateur

Samson

Samson Stage XPD1 Manuel utilisateur

Samson

Samson Go Mic Manuel utilisateur

Samson

Samson AirLine Manuel utilisateur

Samson

Samson SynthSeven Manuel utilisateur

Samson

Samson CONCERT SERIES IV Manuel utilisateur

Samson

Samson UHF 801 Manuel utilisateur

Samson

Samson Concert 77 Manuel utilisateur

Samson

Samson Concert 288 Manuel utilisateur

Samson

Samson DK705 Manuel utilisateur

Samson

Samson Stage v466 Manuel utilisateur

Samson

Samson Stage 55 Manuel utilisateur

Samson

Samson Stage XPD1 Manuel utilisateur

Samson

Samson WSM Wireless System Manager for Windows 95 Manuel utilisateur

Samson

Samson STAGE 266 HT6 Manuel utilisateur

Samson

Samson Concert88 Manuel utilisateur

Samson

Samson AIRLINE CR77 Manuel utilisateur

Samson

Samson VHF Series Manuel utilisateur

Samson

Samson Go Mic Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur