Salus RT310RF Manuel utilisateur

Installation Manual

Model: RT310RF

Product Compliance .................................................................................................. 3

Safety Information ....................................................................................................... 3

Box Content .................................................................................................................... 3

Introduction ................................................................................................................... 4

Features ............................................................................................................................. 5

Installation ....................................................................................................................... 5

Button functions and keys .................................................................................... 7

Installer mode ............................................................................................................... 9

Operations ...................................................................................................................... 10

Other functions ............................................................................................................12

Factory reset ...................................................................................................................13

Technical info ................................................................................................................ 13

Warranty ........................................................................................................................... 14

02 RT310RF Installation Manual

Contents

Product Compliance

Safety Information

This product complies with the essential requirements and other relevant provisions of the following

EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of

Conformity is available at the following internet address: www.saluslegal.com.

Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry.

Thisproduct mustbeinstalled bya competentpersonand inaccordancewithall theEU andnational regulations.

Always isolate the AC Mains supply before installing or working on any components that

require 230 VAC 50Hz supply.

Box content

The box includes the 310RF thermostat, the RT310 receiver (pre paired), 2 AA batteries a set of screws and the

Quick Guide installation manual.

RT310RF thermostat RXRT510 receiver

2xAA batteries and 4x screws Installation Quick Guide

RT310RF Installation Manual 03

Introduction

A room thermostat simply switches the heating system on and off as necessary. It works by sensing the air

temperature, switching on the heating when the air temperature falls below the thermostat setting, and

switching it off once this set temperature has been reached.

Turning a room thermostat to a higher setting will not make the room heat up any faster. How quickly the room

heats up depends on the design of the heating system, for example, the size of boiler and radiators. Neither

does the setting affect how quickly the room cools down. Turning a room thermostat to a lower setting will

result in the room being controlled at a lower temperature, and saves energy.

The heating system will not work if a time switch or programmer has switched it off.

The way to set and use your room thermostat is to find the lowest temperature setting that you are comfortable

with, and then leave it alone to do its job. The best way to do this is to set the room thermostat to a low

temperature – say 18⁰C – and then turn it up by one degree each day until you are comfortable with the

temperature.

You won’t have to adjust the thermostat further. Any adjustment above this setting will waste energy and cost

you more money.

If your heating system is a boiler with radiators, there will usually be only one room thermostat to control the

whole house. But you can have different temperatures in individual rooms by installing thermostatic radiator

valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose a temperature that is reasonable

for the whole house. If you do have TRVs, you can choose a slightly higher setting to make sure that even the

coldest room is comfortable, then prevent any overheating in other rooms by adjusting the TRVs.

Room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains

or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from

working properly.

04 RT310RF Installation Manual

The RT310RF from SALUS Controls is a stylish and

accurate digital thermostat with an easy to read Liquid

Crystal Display (LCD).

The Receiver is used for wiring connections and heat on/

off control. The thermostat provides the user interface

and temperature sensing / control. The two units are

linked together by a Radio Frequency (RF) signal.

Features

Frost protection

Low-Battery Warning

Low-Battery Detection

Modern Casing

Sleep Mode

User Friendly

Pre-Paired in Factory

RF Test Pairing

Features

Installation

The DIP switches are found on the rear of your thermostat and can be used to change the span (temperature

accuracy) of your thermostat from the default +/-0.5°C to +/-0.25°C. This may cause your boiler to operate

more frequently. The DIP switches are located on the back of the thermostat. ON +/-0.25°C, OFF +/-0.5°C.

The span is the accuracy with which the thermostat operates when displaying your temperature. You can

increase the accuracy by setting the span to +/-0.25°C, meaning that your thermostat will be sensitive to a

quarter of a degree temperature change and will activate/deactivate the boiler.

DIP switch settings

+/-0.25

+/-0.5

Note: Please insert batteries into the RT310RF thermostat and it will power up..

RT310RF Installation Manual 05

Connecting the RXRT510 receiver

AUTO

OFF

MANUAL

Wall mounting

COMNO L N

Terminal Description Receiver Terminals

COM

Switch Terminal

Common Switch

Terminal

Mains Live (230VAC)

Mains Neutral

Wiring

Fit the front housing.

Press lightly

Fix the backplate to the wall Align the front housing

at the top edge.

NO COM L N

L N

Electrical diagram

COMNO L N

Unscrew the backplate of the RXRT510 receiver in order to do the wiring connections. After that please switch

the receiver ON.

06 RT310RF Installation Manual

Button functions and keys

Key Function

Turn on the LCD backlight

Turn On/Oﬀ the Frost Mode

Increase button

Decrease button

1. Press once to enter/exit in RF Test Mode

2. Press for 3 seconds to enter/exit Pairing Mode

Press for 3 seconds all the buttons to enter Installer

Mode

AUTO

OFF

MANUAL

Key/LED Function

AUTO System receiver output will switch on and oﬀ

in relation to the command from the RT310RF

transmitter.

Manual System receiver output is controlled by the On/Oﬀ

slide switch.

ON When in Manual Mode, ON will turn on the boiler.

OFF When in Manual Mode, OFF will turn oﬀ the boiler.

Red Led Receiver On, paired.

Green Led Command from thermostat received.

There are few user controls for the RT310RF, making this thermostat very easy to operate. These controls are

shown below, along with a description of each of their functions. The temperature displayed on the LCD is the

current room temperature. All teh LCD icons with a description are shown below.

Thermostat

Receiver

Thermostat LCD Icon Meaning

Thermostat is calling for heat

Thermostat is in Frost Protection Mode

Thermostat is paired with the receiver

Low Battery Warning Indicator

Current Temperature/Set Point Temperature

TESTING/PAIRING

RT310RF Installation Manual 07

Test Pairing Function

Make sure your devices are wired and the thermostat has batteries inserted. Switch receiver to ON. If you are

using the RT310RF pack, the pairing between the thermostat and the receiver is already done. If you bought

the RT310TX and RXRT510 separately then pair as follows. Please make sure that the Receiver is set on Auto.

AUTO

OFF

MANUAL

AUTO

OFF

MANUAL

TESTING/PAIRING TESTING/PAIRING

Test the pairing process

TESTING/PAIRING

TESTING/PAIRING TESTING/PAIRING

3 Sec Wait 9 minutes for the timeout

process to be complete.

Begin the pairing process End the pairing process

TESTING/PAIRING

3 Sec

Testing the RF transmissions

It is important to site both the Receiver and thermostat in locations where the RF signal cannot be interrupted.

The receiving range between the thermostat and Receiver is approximately 30 metres indoors, however many factors can

affect the RF transmission and shorten the operating distance, e.g. shielding by thick walls, foil back plasterboard, metal

objects such as filing cabinets, general RF interference, and so on. The range is generally large enough for most household

applications, but it is advisable to test the RF transmission from the intended thermostat location to the Receiver location

before fixing the thermostat to the wall.

To check the RF reception, follow the following steps:

1. Press the UP button on the thermostat until the set point temperature is higher than room temperature by a few

degrees.

2. Wait for a few seconds. The Heat on (heat call) indicator should appear on the bottom left of the LCD on the thermostat.

3. Check the green LED on the receiver unit - it should be lit.

4. Press the DOWN button to adjust the set point temperature to be lower than room temperature.

5. Wait for a few seconds, and the Heat on (heat call) indicator should disappear and the green LED should switch off.

6. If at step 3 the green LED is not illuminated, press the TEST/PAIRING button on the thermostat and try to place the

thermostat closer to the Receiver.

7. Repeat steps 1 to 5.

Note: Before beginning the process, switch the receiver On/Oﬀ and then On again to reset it (On/Oﬀ/On).

AUTO

OFF

MANUAL

AUTO

OFF

MANUAL

AUTO

OFF

MANUAL

08 RT310RF Installation Manual

Installer Mode

Press and hold and and keys to enter installation setting.

The first setting is temperature display resolution selection - d01. Press to enter the existing setting.

The setting will start flashing. Press or to change temperature display resolution, wait for 10 seconds

to confirm, then enter d02 (if you didn’t press to save your selection, the change will be confirmed after 10

seconds and the thermostat will return to normal mode). d02 is to set temperature offset, press or to

increase/decrease offset. To exit Installer Mode don’t press any key for 10 seconds, or press

See the table below.

dxx Function Parameter Description Default

value

d01 Temperature display

increments

0.1°C or

0.5°C

Select the temperature display

increments

0.5°C

d02 Temperature oﬀset +/-3.0°C Calibrate your thermostat tempera-

ture

0.0°C

d03 Frost setpoint 5.0°C-17.0°C Set the Frost Point temperature 5.0°C

RESET

Press the three buttons

together for 3 seconds.

3 Sec 3 Sec

3 Sec

RESET

Enter ﬁrst d01 setting. Press

Select increment. Press

TESTING/PAIRING

Continue adjusting the d02 and d03 following the same steps as above.

Once you have ﬁnished setting up all the parameters, press to exit

to home screen, or don’t press any button for 10 seconds and it will

exit automatically.

TESTING/PAIRING

RT310RF Installation Manual 09

Operations

Initial Power UP

After power up, the thermostat is reset. During system reset, all LCD icons are displayed for 2 seconds and

the keys are locked. After that, all keys are unlocked and the thermostat is initialized. Then software version is

shown.The typical reset display is shown below.

The following table shows the settings of the RT310RF digital thermostat after Power on, or after TEST/PAIRING

button is pressed:

Function Status after Reset

Operation Mode Normal mode

Room Temperature 22.0°C, to be renewed within 5 seconds

Setpoint Temperature 20.0°C

°C indicator On

Frost Protection indicator Off

Heat indicator Off

Low-Battery Warning indicator Off, to be renewed within 5 seconds

Output Relay Off

Reviewing Setpoint Temperature

Press or to review Setpoint temperature. The flame icon won’t be turned on.

When operating in Frost protection mode, the LCD will show frost setpoint with the Frost Protection

indicator displayed.

Press Backlight or wait 2 seconds without key press to return to normal operation, room temperature will

be displayed.

Actual room temperature Setpoint temperature

TESTING/PAIRING TESTING/PAIRING

10 RT310RF Installation Manual

Autres manuels pour RT310RF

Table des matières

Autres manuels Salus Thermostat

Salus

Salus VS10WRF Manuel utilisateur

Salus

Salus RT310SPE Manuel utilisateur

Salus

Salus VS20WRF Manuel utilisateur

Salus

Salus Thermo 091 Manuel utilisateur

Salus

Salus iT500 Manuel utilisateur

Salus

Salus ST620VBC Manuel du propriétaire

Salus

Salus RTS00RF Manuel utilisateur

Salus

Salus Quantum SQ610 Manuel utilisateur

Salus

Salus ERT30 Manuel utilisateur

Salus

Salus ERT50 Manuel utilisateur

Salus

Salus RT310RF Manuel utilisateur

Salus

Salus RT510RF Manuel utilisateur

Salus

Salus RT510BC+ Manuel utilisateur

Salus

Salus VS20 Manuel utilisateur

Salus

Salus RT 10 Manuel utilisateur

Salus

Salus RT200 Manuel utilisateur

Salus

Salus SOLO ST920WF Manuel utilisateur

Salus

Salus ST620RF Manuel utilisateur

Salus

Salus PH60 Manuel utilisateur

Salus

Salus RT300 Manuel utilisateur

Salus

Salus RT510WBC Manuel utilisateur

Salus

Salus 091FLRF Manuel utilisateur

Salus

Salus RT200 Manuel du propriétaire

Salus

Salus RT310 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur