Ruckus Wireless SmartZone 300 Manuel utilisateur

Published June 2017, Part Number 800-71631-001 Rev A

Ruckus Wireless™

SmartZone™300

Rack Mount Kit Quick Setup Guide

This Rack Mount Kit Quick Setup Guide provides step-by-step

instructions on how to install the Ruckus Wireless SmartZone

300 (SZ-300) into a server rack using the Ruckus Wireless

902-S330-0000 kit. The SZ-300 is standard 2U server

designed for mounting in a standard EIA 19" server rack.

Before You Begin

Before deploying your Ruckus Wireless product, verify that all

items listed in Package Contents below are included in the

package. If any item is damaged or missing, notify your

authorized Ruckus Wireless sales representative. Also, make

sure that you have prepared the required hardware and tools.

NOTE: Some standard EIA 19” server racks have square or

slotted mounting holes. The fasteners in this kit may not work

with these racks, requiring the customer to supply rack-mount

fasteners.

WARNING! Observe careful handling. The kit may contain

sharp edges.

NOTE: Using sliding rails could result in non-compliance with

Seismic Zone 4 requirements of NEBS-3 certification.

This Guide in Other Languages

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

このガイドの⽇本語版は https://support.ruckuswireless.com

でご覧ください。

이 가이드의 한국어 버전은 웹 사이트

(https://support.ruckuswireless.com)

에서 확인하시기 바랍니다 .

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta guía

en https://support.ruckuswireless.com.

Required Hardware and Tools

• No. 1 Phillips screwdriver

• Ruler for measuring the rack depth

Package Contents

A complete rack mount installation kit includes two rail

assemblies and all of the items listed below:

• Two outer rails with front and rear mounting brackets

• Two inner rails with safety stops

• Eight M4 x 4mm long pan head screws

• Two M5 x 20m long pan head screws

•ThisRack Mount Kit Quick Setup Guide

Step 1: Separate the Rail Assemblies into

Outer and Inner Rails

#1 Extend the inner rail until it locks.

#2 Slide the plastic tab towards the direction of the extension

lock and pull it to direction of the arrow to release the inner

rail.

#3 Remove the inner rail from the outer rail assembly.

Figure 1. Separate the rail assemblies

Step 2: Assemble the Outer Rails to the

Inside of the Rack

#1 Extend the outer rail assemblies with the front stamped

portion protrusions are positioned into the slots of the rack.

Repeat this on the opposite end of the rail until its

protrusions are positioned in the back of the rack.

#2 Repeat step 1 on the adjacent side of the rack.

nsure that

the correct slot levels on the rack are aligned with the

adjacent side rail assembly.

Figure 2. Assemble the outer rails

[

Published June 2017, Part Number 800-71631-001 Rev A

Step 3: Attach the Inner Rails to the Server

#1 Attach the inner rail to the side of the server chassis. To do

this, align the protrusion on the side of the server to the

keyhole cutout on the inner rail, and then slide it in until you

hear a click.

#2 Use one (1) M4 x 4 screw to fasten the inner rail to the

server chassis. Fasten until snug.

#3 Repeat steps 1 and 2 above for the other side of the

chassis.

Figure 3. Attach the inner rails to the server chassis

Step 4: Fasten the Front Mounting Brackets

and Handles to the Server Chassis

The brackets, handles and mounting hardware can be found in

the accessory box in the top tray of the server shipping carton.

#1 Using three M4 x6mm long black fasteners, attach one of

the two front mounting brackets to the right side of the

server chassis.

#2 Using two M3 x4mm fasteners, attach one of the two

handles to the mounting bracket.

#3 Repeat steps 1 and 2 on the left side of the server chassis.

Figure 4. Attach the mounting bracket and handle

Step 5: Slide the Inner Rails into the Outer

Rails and Secure to the Rack

WARNING! The SZ-300 is heavy (45 lbs/20.4 kg). Two people

should work together to lift and slide the server into the rack.

Ruckus strongly recommends against one person attempting

to perform this task alone.

#1 On the inner rail, release the lock on both the left and right

inner rails (attached to the server). See Figure 5.

#2 Extract the ball retainer forward to the front of the rack until

the middle member locks into place.

#3 Align the inner rails (attached to the server) with the

extracted ball retainer of the outer rail assemblies (attached

to the rack.

#4 Engage the matching rails, and then slide the server

chassis into the rack until the two spring safety locks snap

into place.

#5 Engage the matching rails, and then slide the server

chassis into the rack until the two spring safety locks snap

into place.

#6 Pull the plastic tabs on the left and right inner slides and

then continue to push the server into the rack until the front

tabs of the server are seated against the rack vertical rails.

See Figure 5.

Figure 5. Secure the server to the rack using (1) M5 fastener

through the front angle bracket of the server to the

threaded portion of rail assemble in the rack. Repeat

this step on the other side of the server.

NOTE! Make sure the M5 fasteners are snug against the front

brackets on either side of the server to proper secure the

server to the rack.

Congratulations! You have completed mounting the SZ-300

into a server rack.

Wireless are trademarks of Ruckus Wireless, Inc. All other company and

product names mentioned in the documentation are held to be trademarked

(and registered) by the primary holders.

Handle

Mounting bracket

Autres manuels pour SmartZone 300

Ce manuel convient aux modèles suivants

Autres manuels Ruckus Wireless Point d'accès sans fil

Ruckus Wireless

Ruckus Wireless ZONEFLEX R310 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 2942 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R560 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex H500 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex R510 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless C500 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless T300 Manuel d'instructions d'installation

Ruckus Wireless

Ruckus Wireless T610 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless C110 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless Unleashed R310 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-S Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R730 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Manuel utilisateur

Ruckus Wireless

Ruckus Wireless SmartCell Gateway 200 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless SmartCell 8800-S Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R720 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless T710 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless H320 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7962 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless T310s Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur