Ronda QM1 Manuel utilisateur

PROFESSIONAL INSTALLATION REQUIRED

Installation, Use & Care

Guide

Double Drawer/Cooler Units QM1

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 2 / 6

PROFESSIONAL INSTALLATION REQUIRED

Welcome & congratulations

Congratulations on your purchase of this double drawer.

We at Ronda are very proud of our product and we hope you consider us for fu-

ture purchases.

This product is made in our factory in Italy with components all made in Italy.

For any questions contact us at : [email protected]

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS

Packaging contents:

# 1 SMC Cabinet

# 2 Drawers

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 3 / 6

PROFESSIONAL INSTALLATION REQUIRED

Notes and Installation Tips

ALWAYS USE PROTECTION GLOVES AND EYE SAFETY GOGGLES:

Use care and always use protection gloves and safety goggles during in-

stallation and care. Because the drawers may have sharp edges, if not

handled with care they can cause cuts and abrasions.

Tools you will need : Power screw driver, manual screw driver, level, tape

measure.

Carefully unpack cabinets making sure not to scratch stainless steel fronts

and not to loose or misplace any components.

DO NOT remove polyethylene protective coating until installation is com-

plete.

Remove all drawers before installation. This will make cabinet easier to lift

and install and give access to installation hardware.

This product is made only for application on a subframe, which can be

made in different materials (wood, plastic, alluminium) into a wall structure

(Fig. 1)

Do not use the drawers as ladder. This would be dangerous for you and can

cause the item to break.

Fig. 1

Subframe

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 4 / 6

PROFESSIONAL INSTALLATION REQUIRED

Before Installation

Verify model number on the box label.

Verify the counter hole measure refering to the following table :

The maximum deviation permitted is : 0.04’’ (1 mm). Otherwise the SMC

panels get deformed and drawers don’t work properly. Use spacers to get

the right counter hole dimensions.

Checkwith a level that

Verify with a level the horizontal and vertical level of the counter hole and

correct if not accurate.

Counter Hole

Model a b

+0,04 + 0,04

inch

14.96

24.44

+1 +1

QM11

mm 380

621

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 5 / 6

PROFESSIONAL INSTALLATION REQUIRED

Assembly and Installation

Carefully unpack cabinet making sure not to scratch stainless steel fronts.

Stainless is protected by a plastic coating that must be removed after

setup.

Remove drawers and store in a safe place.

Put the cabinet inside the counter

hole.

ATTENTION:

To correctly insert the cabinet , the slots

on the guides must be turned upward.

( see the foto down side )

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 6 / 6

PROFESSIONAL INSTALLATION REQUIRED

Be sure that the cabinet fits well in

the wall.

No clearanceshould be left be-

tween the edges of the cabinet and

the wall.

If not, use spacers to fit.

Secure the cabinet to the wall with

screws in the dedicated matching

holes in the cabinet.

Use # 12 mushroom head screws.

Insert the drawer rear wheels into the guide slots.

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 7 / 6

PROFESSIONAL INSTALLATION REQUIRED

Put the drawer forward,

than lift a bit to insert the

second wheel and put in-

side.

Close completely the

drawer.

Repeatfor the second drawer

the operationfrom 6 to 7.

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 8 / 6

PROFESSIONAL INSTALLATION REQUIRED

Care and cleaning

It is imperative that the owner realizes that he/she is required to perform

reasonable maintenance and care of the drawers in order to maintain the

manufacturers warranty. Failure to perform reasonable maintenance and

care may void the warranty.

The following is a list of maintenance steps and things to avoid. This is not

intended to be a complete list, but is to be used as a guideline for general

care.

Carefully remove protective plastic peel coat from each stainless steel surface.

External Surfaces:

Clean stainless with stainless steel cleaner in direction of grain. Rubbing across

the grain direction may produce minor scratches. Recommended cleaners are

Weiman

, Stainless Steel Magic

and Sheila Shine

In a salty air environment, a slightly more oily cleaner like Sheila Shine

will pro-

tect better against oxidation, pitting or slight surface rust. Cleaning the surfaces

periodically will protect the finish for many years. In a heavily salty area, you will

have to clean more frequently as salt breaks down into highly corrosive chlorine

that will attack the metal. Surface corrosion will not affect performance of the

product, but will affect the look.

DO NOT USE scratchy pads, scouring pads, or stiff sponges for cleaning. Do not

use abrasive detergents, powdered cleansers or detergents containing acid sub-

stances or bleach.

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 9 / 6

PROFESSIONAL INSTALLATION REQUIRED

Internal surfaces:

Clean the internal surface of the cabinet use warm water and soap.

Wash after each use and dry to avoid formation of molds and staining.

The cabinet’s working surface are constructed from Sheet Moulding Coumpound

(SMC), a glass rinforced polyester resin resistent to corrosion.

Removing and cleaning the magnetic gasket :

•Carefullyinsertascrewdriverinto acornerof

thegasket(1).

•Liftthegasket untilitexitsfromtheseat(2).

•Removethegasketbyhand (3).

•Cleanwithwater andneutraldetergent.

•Insert the gasket inits seat andstrongly

pressitonalltheperimeter.Youcanlubri-

catethegasketseattodothiseasly.

Drawer Guides

Drawer load capacity should not exceed 50 lbs per drawer. Never use an ex-

tended drawer for a ladder or a work platform.

IL-MO-044 Rev. 1 04/2010

Double Drawer Unit – QM1

Insulated

Pag. 10 / 6

PROFESSIONAL INSTALLATION REQUIRED

WARNINGS

•Surfaces can be very hot when exposed to direct sunlight.

•Molds can form if not properly dried.

•Do not use as a ladder.

•Avoid any contact with electrical outlets or wires.

•This is only a food container. It is not a refrigerated space,

and will not prevent food spoilage.

•If exposed to temperatures below – 4 °F and above + 120 °F

deformation and malfunction of the drawers can occur.

•If installed adjacent to the heating elements of a barbeque,

insulation can be less effective.

•If installed near to the sea, damage from salty water can oc-

cur.

•Keep drawers closed when not in use.

Table des matières

Autres manuels Ronda Tiroir LCD

Ronda

Ronda QM2 Manuel utilisateur

Manuels Tiroir LCD populaires d'autres marques

Acnodes

Acnodes KD 8228 Manuel utilisateur

Ameriwood

Ameriwood 9524328PCOM Manuel utilisateur

Kesseböhmer

Kesseböhmer TANDEM solo Manuel utilisateur

Crystal Image Technologies

Crystal Image Technologies RMD-151-A Series Manuel utilisateur

APW Wyott

APW Wyott Ease Extreme HDX-1-120 Manuel utilisateur

NTI

NTI RACKMUX-V17-N Manuel utilisateur

Austin Hughes

Austin Hughes CyberView L120 Manuel utilisateur

Uplift Desk

Uplift Desk STR018 Manuel utilisateur

Acnodes

Acnodes KDC 81932 Manuel utilisateur

Acnodes

Acnodes RK1200T Manuel utilisateur

StarTech.com

StarTech.com DuraView RACKCONS1501 Manuel utilisateur

Mocka

Mocka Mischa Manuel utilisateur

GRASS

GRASS DWD XP Manuel utilisateur

StarTech.com

StarTech.com DuraView RACKCONS1701 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S Manuel utilisateur

Synergy Global Technology

Synergy Global Technology LCD1U17-44 Manuel utilisateur

Fujitsu

Fujitsu RC25 Manuel utilisateur

Acnodes

Acnodes RK 1000B Manuel utilisateur