Fisher & Paykel IZONA CoolDrawer RB36S Manuel utilisateur

WARNING!

Electrical shock hazard

Disconnect product from main power supply before installing appliance.

Failure to do so may result in electrical shock or death

Important safety precautions!

Installation of this CoolDrawer requires competent mechanical and electrical skills.

Be sure to leave these Instructions with the Customer.

Installation must comply with your local building and electricity regulations.

At the completion of the CoolDrawer installation, the Installer must perform the Final Check List.

Remove all packaging materials supplied with the CoolDrawer.

The CoolDrawer is manufactured for indoor use only.

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and speciﬁcation availability in your country, please go to our

website www.ﬁsherpaykel.com or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

The CoolDrawer MUST be installed to allow for future removal from the enclosure if service is required.

Do not seal this CoolDrawer into the cabinetry with silicone or glue. Doing so will make future servicing

dicult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in

product, nor for repairing any damage that may be incurred by doing this.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the

power supply cord.

Failure to install the CoolDrawer correctly will invalidate any warranty or liability claims.

If the power supply cord is damaged, it must be replaced. Parts are available from your Authorised Fisher

& Paykel dealer.

Cabinetry must be suciently robust to support a combined product and food load of 100 kg (220 lb).

Bearers may be required to support the internal shelf.

Before you install the CoolDrawer, please make sure that

The switched power outlet must be outside the refrigerator drawer cavity so that it is accessible after

installation.

The switched power outlet must be located outside the cavity, within 55” (1400 mm) from the CoolDrawer

cavity if situated on the left-hand side of the cavity and within 33” (840 mm) if situated on the right-hand

side of the cavity.

The services hole in the refrigerator cavity needs to be large enough for the power supply plug to t

through.

IZONA CoolDrawer

Installation instructions

FRAMED CABINETRY

WARNING!

Tipping hazard

Do not operate this apppliance until it has been securely anchored inside the

cabinetry. The cabinet must be securely anchored to the oor.

Failure to use caution could result in injury or cuts.

RB36S & RB90S models

2PRODUCT DIMENSIONS

1 ”

(50 mm)

Product dimensions (inches (mm))

CoolDrawer

RB36S

RB90S

Aoverall height of product (inc. installation brackets)

Boverall width of product

Coverall depth of product (excl. drawer panel; inc. power cord)

Ddepth of drawer (open) (excl. handle)20 ½” (520)

Installation diagrams for illustration purposes only

Cabinetry dimensions (inches (mm))

CoolDrawer

RB36S

RB90S

Aoverall width of cabinetry frame 36” (914)

Bminimum inside width of cabinetry frame 34” (864)

C1height below top of internal shelf*

(to allow for outlet duct height)

max. 4 ¾” (120)

C2height from frame inner face to top of internal shelf

Dminimum height of toe kick 3” (75)

Eminimum depth** of toe kick

Fminimum distance from front of cabinetry to rear wall

**All depth measurements are taken from the front face of the cabinetry frame (not drawer panel)

Minimum clearances (inches (mm))

” (2 mm)

½” (13 mm)

Installation diagrams for illustration purposes only

An alternative of wooden blocks

can be used instead of the internal

shelf to position the product at the

correct height.

3CABINETRY DIMENSIONS

PARTS SUPPLIED

5CAVITY PREPARATION

max.

¾”(20 mm)

max.

33”

(840

mm)

min. ø

(

50 mm)

Benchtop

Panel

min. 21”

(

535 mm)

Important!

Disconnect power to surrounding appliances before preparing cavity.

Recommended to allow the vertical removal of the refrigerator bins.

min.

5” (

130 mm)

Installation

trims (2)

Installation brackets

(left-hand and right-

hand side) (2)

Outlet duct (1)Trim brackets (4)Drawer Panel

attachment

hooks (3)

Power

cord (1)

Phillips 16 mm

( wood

screw (6)

Pan Head

16 mm (

screw (12)

Pan Head

16 mm (

screw (2)

Phillips

16 mm

( wood

screws (6)

Note: Services can be located

either side of CoolDrawer.

min.

21” (

535 mm)

min.

5” (

130 mm)

Shows cutout if cabinetry

depth at

(

550 mm)

6PANEL PREPARATION

Integrated Panel material

(16 - 20 mm) panel thickness (

¾”

(18 mm) recommended).

Maximum weight of 7 kg (15.5 lb).

Adequately sealed to withstand moisture (122

F/50

C @ 80% RH)

Height of Drawer Panel

The following information is required to correctly dene your drawer panel height:

Dimension Data Source

AReveal dimension Your kitchen designer

BHeight between top of Internal shelf and Your kitchen designer

underside of benchtop

CBottom face of Drawer panel to top of internal shelf Min. 6” (152 mm)

Max. 7

” (184 mm)

DDrawer panel height Calculated from A, B & C

To calculate D complete the following equation:

D = B - A - C

i.e. For the F&P prenished panel with a

“ (6 mm) reveal:

” (476 mm) =26

” (666 mm) -

”(6 mm)

” (184 mm)

Height of the False Panel

Determine the height of the false panel according to your individual kitchen cabinetry

requirements maintaining a ” (4 mm) gap between panels.

F&P prenish panel width is 35

” (896 mm)

Installation diagrams for illustration purposes only

Drawer Panel

(16 - 20 mm)

height of False

Panel

False Panel

width of Panels

height of

Drawer Panel

(4 mm)

Section A-A

Benchtop

Drawer panelFalse panel

2 2

3 3

30 ” (764 mm)

1 ” (50 mm)*

4 ” (102 mm)

max. R ” (16 mm)

11” (280 mm)

8 ½” (215 mm)

max. 33 ” (862 mm)

min. 33 ” (860 mm)

”

(25 mm)

3” (76.5 mm)*

1 ”

(40 mm)

CREATE CUTOUTS IN FRAME

9ATTACH OUTLET VENT DUCT

If the cabinetry does not already have cutouts, ensure the modications below are made.

Important!

Ensure the power cord is clipped in place.

Important!

Ensure a minimum of 3 screws

per side are used. The rear screws

must always be used. Horizontal

xing is also optional.

LOCATE & SECURE INSTALL BRACKETS

*Cutout dimensions referenced from inside face of cabinetry frame.

10 ATTACH POWER CORD & TRIM BRACKETS

Important!

Cut outlet duct to be ush

with top of internal shelf.

Important!

Note correct orientation of bracket.

3 4 5

6 7 8

1 ” (46 mm)

9 mm

x 3

”

(2.5 mm)

(35 ½” (902 mm))

” (1 mm)

” (5 mm)

”

(18 mm)

12 ¼” (311 mm)12 ¼” (311 mm)

16 ” (414 mm) X

- ”

(16 - 20 mm)

11 MOVE PRODUCT INTO CAVITY

13 ATTACH DRAWER PANEL TO FRONT OF DRAWER

Important!

Do not screw in trim

brackets at this stage.

Hook drawer panel onto

drawer front channel

Close the drawer and

check vertical clearances

Remove the panel and

adjust the TOP

attachment hooks

as necesary

Replace panel on

drawer and conrm

vertical clearances

Slide panel to achieve even

horizontal clearances

Open drawer and

clamp panel onto

drawer by tightening

the BOTTOM

attachment hook

Close the drawer and ensure it is ush

with adjacent cabinetry. If not, the

product may have to be pulled back

or forward.

Important!

Be careful not to damage power

supply cord when pushing

product into cavity.

12 FIT DRAWER PANEL ATTACHMENT HOOKS

Ensure there is clearance

between panel and cabinetry

when drawer is fully closed

Attach handle as necessary.

Ensure all screws are ush

with panel surface.

C is bottom face of panel to

top of internal shelf, see 6

” (4 mm)

” (2 mm)

14 SECURE TRIM BRACKETS TO CABINETRY

16 ATTACH FALSE PANEL

Important!

Ensure you check basic operation and perform

the nal checklist.

Attach the false panel securely

as recommended by the cabinet

maker.

Important!

The false panel needs to be removeable for

servicing.

15 ATTACH TRIMS TO SIDES OF CABINETRY

17 CHECK OPERATION

Open drawer and secure product

to cabinetry using four Trim

brackets and screws.

www.sherpaykel.com 840509 FRAMED CABINETRY 02.08

18 FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Has all packaging been removed from the appliance?

Is the appliance securely fastened to the cabinetry?

Does the drawer slide freely and close properly?

Has the outlet duct been installed correctly?

Is the appliance level?

Are the panels securely attached?

Have the panels been properly aligned for correct operation and

appearance? Are all clearances even?

Is there clearance between drawer and cabinetry frame?

Has the power cord been plugged into a properly grounded 3-prong outlet,

which has been installed in accordance with all applicable electrical codes?

OPERATION:

Is the control panel lit?

Can you hear the compressor motor running?

When a hand is placed near the toe kick, can airow be felt under front

right-hand side of appliance?

Have you demonstrated the basic operation to the customer?

Installer’s name:

Installer’s signature:

Installation company:

Date of installation:

LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER

Autres manuels pour IZONA CoolDrawer RB36S

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fisher & Paykel Tiroir LCD

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S Manuel utilisateur

Fisher & Paykel

Fisher & Paykel WB24S Manuel utilisateur

Fisher & Paykel

Fisher & Paykel MINIMAL VB60SDEB1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel VB60SMB1-SET Manuel utilisateur

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB90S Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RB36S25MKIW Manuel utilisateur

Fisher & Paykel

Fisher & Paykel 9 Series Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OMD24SPX1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RB90S64MKIW Manuel utilisateur

Fisher & Paykel

Fisher & Paykel MINIMAL VB24SDEB1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel MINIMAL VB24SDEB1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel WB60SDEX1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S Manuel utilisateur

Fisher & Paykel

Fisher & Paykel COOLDRAWER Manuel de service

Fisher & Paykel

Fisher & Paykel DS603SS Manuel utilisateur

Fisher & Paykel

Fisher & Paykel 9 Series Manuel utilisateur

Manuels Tiroir LCD populaires d'autres marques

Acnodes

Acnodes KD 8228 Manuel utilisateur

Ameriwood

Ameriwood 9524328PCOM Manuel utilisateur

Kesseböhmer

Kesseböhmer TANDEM solo Manuel utilisateur

Crystal Image Technologies

Crystal Image Technologies RMD-151-A Series Manuel utilisateur

APW Wyott

APW Wyott Ease Extreme HDX-1-120 Manuel utilisateur

NTI

NTI RACKMUX-V17-N Manuel utilisateur

Austin Hughes

Austin Hughes CyberView L120 Manuel utilisateur

Uplift Desk

Uplift Desk STR018 Manuel utilisateur

Acnodes

Acnodes KDC 81932 Manuel utilisateur

Acnodes

Acnodes RK1200T Manuel utilisateur

StarTech.com

StarTech.com DuraView RACKCONS1501 Manuel utilisateur

Mocka

Mocka Mischa Manuel utilisateur

GRASS

GRASS DWD XP Manuel utilisateur

StarTech.com

StarTech.com DuraView RACKCONS1701 Manuel utilisateur

Synergy Global Technology

Synergy Global Technology LCD1U17-44 Manuel utilisateur

Fujitsu

Fujitsu RC25 Manuel utilisateur

Acnodes

Acnodes RK 1000B Manuel utilisateur

I-Tech

I-Tech RKP115 Manuel utilisateur