Roland ColorCAMM Pro Mode d'emploi

Us er Maintenance G uide

How to ...

1 - clean the s heet

2 - clean the P rint Head by C leaning P en

3 - exchange the C leaning P ad

4 - clean the P rint Head by C leaning S heet

5 - store the sheet

The ins tructions in this guide are not only for producing

high quality printing res ults , but als o to prevent the Print Head

from being cons umed or broken. P leas e read this guide

carefully to pproperly perform the periodic c leaning.

Pull out the amount to be used for printing.

This can be performed most easily if you set the

sheet on the PC-60 after powering off.f.

Wipe the surface of the sheet strongly with a cloth soaked

in alcohol to remove the dust and oil.

Please use a cloth which produces little or no fiber dust.

Make sure not to put alcohol on the P L AT E N.

1 - C lean the s heet and C leaning P ad

Make s ure to c lean the s heet every time before printing. Dus t or oil on the

s urface of the s heet c ould res ult in poor printing res ults . Als o, partic les of hard

materials s uch as s and could res ult in damage to the print head.

Check and make sure that the CL EANING PAD is not dirty. .

If there is dust, please remove it with a brush.

R aise the head cover with your fingur.

Clean the edge of the printing head with the cleaning pen.

It is not necessary to clean the bottom part.

NOT E !

Make s ure not to make contac t to

the rubber roller with c leaning pen.

E DG E of HE AD

2 - C lean the P rinting Head with C leaning P en

P erform this c leaning only when you have s cratc hy printing or fine lines acros s the image.

Turn off the sub power by pressing key.

Open the front cover and move the printing head to the left

side of the machine.

NOT E !

Do not rais e the cover too forc e-

fully or the head could break.

NOT E !

Make s ure not to make c ontact to

the platen with c leaning pen.

P osition the material, the pinch rollers, and the grit

rollers at the locations shown above.

P inch R oller

S ensor

Open the front cover.

R aise the sheet loading lever.

Unload the sheet from the machine.

Take out the ink ribbon cartridge and remove the blade

holder.

While pressing the SHEE T T Y PE key, turn on the sub power

by pressing key.

Position the sheet, pinch rollers, and the grit rollers at the

locations shown in the figure.

Pinch rollers should be on the black lines on the cleaning

sheet. Also make sure that the sensors are covered.

C leaning S heet

P erform this c leaning only when you have s cratc hy printing or fine lines acros s the image.

Turn off the sub power by pressing key.

When the front cover is closed, head cleaning begins.

Head cleaning is finished when the B USY L E D goes

dark and the PIE CE L E D flashes.

When cleaning is finished, raise the sheet loading lever

and remove the sheet.

L ower the sheet loading lever..

If the sheet is not loaded at the correct location, the PIE CE

and R OL L L E Ds flash at the same time.

If this happens, reload the sheet at the proper location.

Turn off the sub power by pressing the key.

1 R emove the backing of the cleaning pad.

2 Move the platen to the right side.

3Place the new cleaning pad by pushing it toward the

left side.

** Make sure that the cleaning pad is not loose.

Affix the new cleaning pad.

Remove the old cleaning pad from its right side.

Check the following:

1. Make sure that the there is a gap between the platen

and the cleaning pad.

2. Make sure that the platen damper moves in 4 direc-

tions: left, right, front and rear.

If the platen doesnÕt move smoothly, it could cause poor

printing results.

4 - E xchange the C leaning Pad

P laten

Backing

C leaning P ad

Make s ure to replace the cleaning pad when it becomes dirty (turns brown) or fluffy..

Us ing a dirty or fluffy cleaning pad could res ult in a damage to the head.

Table des matières

Autres manuels Roland Imprimante

Roland

Roland XC-540W Manuel utilisateur

Roland

Roland TrueVIS AP-640 Manuel utilisateur

Roland

Roland SJ-745EX Guide de démarrage rapide

Roland

Roland VersaEXPRESS RF-640 Manuel utilisateur

Roland

Roland VersaCAMM SP-300S Manuel utilisateur

Roland

Roland SOLJET PROIII XC-540 Manuel utilisateur

Roland

Roland VersaSTUDIO Manuel utilisateur

Roland

Roland VersaUV LEF2-200 Manuel d'utilisation et d'entretien

Roland

Roland SOLJET PRO4 XF-640 Manuel utilisateur

Roland

Roland HB-12 Manuel utilisateur

Roland

Roland EU-1000MF Manuel utilisateur

Roland

Roland SP-540i Manuel utilisateur

Roland

Roland VersaUV LEF2-300 Manuel utilisateur

Roland

Roland CAMM-2 PNC-2300 Manuel de la liste des pièces

Roland

Roland Texart RT-640 Mode d’emploi

Roland

Roland VersaCamm SP-540V Manuel utilisateur

Roland

Roland VersaUV LEJ-640 Manuel utilisateur

Roland

Roland PR-1111 Manuel utilisateur

Roland

Roland VersaUV LEJ-640 Manuel d'utilisation et d'entretien

Roland

Roland VersaCamm VP-540 Manuel utilisateur

Roland

Roland Advanced Jet AJ-1000 Manuel d'utilisation et d'entretien

Roland

Roland VersaUV LEC2-330 Manuel utilisateur

Roland

Roland CJ-540 Manuel utilisateur

Roland

Roland SOLJET Pro 4 XF-640 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur