Roland VP Series Manuel utilisateur

Reinitialize the Limit

Step By Step Procedure

for VP & RS models

Do It Yourself Guide

Roland Support Document Date: 07/15/09 Revision 1.0

Reinitialize The Limit - Do It Yourself Guide

Reinitialize The Limit is the process of telling the printer several vital pieces of information that can be lost for various reasons.. These

pieces of information are, the home position and the cut down position. When both of these factors are known the machine will then

understand the width or printable area. Head crashes are the most common cause of needing to Reinitialize The Limit. However,

these steps need only be performed if the symptoms below are exhibited.

Symptoms indicating a Reinitialize The Limit may be needed:

When powering the machine on the model type is listed as XX-??? For example VP-??? or RS-???

When “Sheet Cut” is performed the carriage performs the motion but does not engage the cutter correctly.

Carriages are disconnected error occurs repeatedly.

Scan Motor errors occur repeatedly.

This is a simple process that when performed correctly takes just a few minutes to complete.

Performing the Reinitialize The Limit process

Continued Next Page

Move the Print Carriage out of the home position. Press the Carriage to the Right and

then gently move it back towards the Left.

1. 2.

Power the machine OFF from the front

panel.

Remove the two screws that hold the

right hand cover and remove the cover.

5. 6.

Gently push the Print Carriage to the

Left as shown to insure the Lock is set

properly. The Print Carriage should

not move.

Hold the LEFT, UP, RIGHT Arrow

Keys and Press the Sub Power Key.

Setting Up The Limit will appear on the

LCD panel. Press Enter

4.Once freely moving, return the Print Carriage to the lock position on the right. Once the

Print Carriage reaches the correct position an audible “click” will be heard indicating the

lock has been engaged. Do not move the Print Carriage too far to the Right or the

Lock will not engage correctly.

Tech Tip: Locking the Print Carriage takes a steady hand and patience. It may take several

attempts before the Lock is achieved. Do not continue the process without locking the

Print Carriage otherwise the process will not complete.

Roland Support Document Date: 07/15/09 Revision 1.0

Reinitialize The Limit - Do It Yourself Guide

Further Support

Should further support be needed or any additional questions arise about the processes in this document please contact your local

supporting dealer. As always, thank you for choosing Roland.

7. The LCD Panel will now read DETECTING. It is at this time the printer will go through

a procedure and an error may occur. If an error occurs at this time it is most likely that the

Print Carriage was not locked correctly. Power the machine OFF and start the process

again from Step 1.

8. Once the home position is set up the LCD Panel will read “SETTING UP CUTTER DOWN

POS”. At this time the Cutter Carriage should have separated from the Print Carriage. If

the Cutter Carriage has not separated from the Print

Carriage power the machine OFF and start the process

again from Step 1.

11.Shortly after the Cut

Carriage returns the LCD

Panel will read INITIALIZE

COMPLETED.

9. Take the Cutter Carriage and bring it to the left hand side of the machine and press it ﬁrmly

against the inner wall to engage the Sheet Cutter. The Sheet Cut Blade will visibly engage at

this time. This action deﬁnes the width of the printer and sets the position for engaging the sheet

cutting blade.

10.Leave the Cut Carriage at the Left

side of the machine and Press ENTER

on the control panel. The Cut Carriage

will return to the right hand side.

12.Power OFF the machine and restart as

normal. The machine is now ready for use.

If the Limit Initialize fails repeat the

process from Step 1.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Roland Traceur

Roland

Roland VersaUv LEF - 12i Manuel utilisateur

Roland

Roland TrueVIS VG-640 Manuel du propriétaire

Roland

Roland DPX-3700A Manuel utilisateur

Roland

Roland VersaEXPRESS RF-640 Manuel utilisateur

Roland

Roland VersaCamm SP-540V Manuel utilisateur

Roland

Roland VS-640i Manuel d'utilisation et d'entretien

Roland

Roland Camm-1Pro Series Manuel utilisateur

Roland

Roland TrueVIS Series Caractéristiques techniques

Roland

Roland DXY-1300 Manuel d'installation

Roland

Roland CAMM-1 GS-24 Manuel utilisateur

Roland

Roland VS-640 Manuel d'utilisation et d'entretien

Roland

Roland PNS-401 Manuel utilisateur

Roland

Roland CAMM-1 PRO Manuel utilisateur

Roland

Roland CAMM-1 PRO CM-500 Manuel d'utilisation et d'entretien

Roland

Roland SOLJET Pro 4 XR-640 Manuel utilisateur

Roland

Roland CX-500 Manuel utilisateur

Roland

Roland VersaEXPRESS RF-640 Manuel utilisateur

Roland

Roland VersaUv LEF - 12i Manuel utilisateur

Roland

Roland Hi-Fi Express FP-740 Manuel utilisateur

Roland

Roland VersaCamm VP-540 Manuel d'utilisation et d'entretien

Roland

Roland GX-24 Manuel utilisateur

Roland

Roland VT-200 Manuel utilisateur

Roland

Roland soljet pro4 xf 640 Manuel utilisateur

Roland

Roland DXY_1350 Manuel utilisateur

Manuels Traceur populaires d'autres marques

MUTOH

MUTOH Kona 760 Manuel utilisateur

HP 7475a Manuel utilisateur

Vulcan-Hart

Vulcan-Hart FC-500VC Manuel utilisateur

Furuno

Furuno RP-180 Manuel utilisateur

MIMAKI

MIMAKI CF2 Series Manuel utilisateur

Ioline

Ioline Summit Manuel utilisateur

Summa

Summa S CLASS Manuel utilisateur

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuel utilisateur

Furuno

Furuno RP-17 Manuel utilisateur

HP 7470A Manuel utilisateur

SII

SII LP-1010 Manuel utilisateur

Great Computer

Great Computer JII-61 Manuel utilisateur

Lectra

Lectra Alys 120 Manuel utilisateur

MUTOH

MUTOH Ultima SC-850D Manuel utilisateur

Skycut

Skycut D Series Manuel utilisateur

Commodore

Commodore 1520 Manuel utilisateur

Esko

Esko Kongsberg XE Manuel utilisateur

MUTOH

MUTOH Blizzard Manuel utilisateur