Roland VersaEXPRESS RF-640 Manuel utilisateur
Setup Guide
Thank you very much for purchasing this product.
- To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through
this manual completely and store it in a safe location.
- Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
- The contents of this manual and the specications of this product are subject to change without notice.
- This manual and the product have been prepared and tested as much as possible. If you nd any misprint or error, please
inform us.
- Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this
product, regardless of any failure to perform on the part of this product.
- Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any
article made using this product.
Company names and product names are trademarks or registered trademarks of their respective holders.
http://www.rolanddg.com/
Copyright © 2014 Roland DG Corporation
Contents
Contents........................................................................................................2
1. Installation Environment............................................................................3
Deciding on an Installation Site .................................................................................................. 3
Temperature and Humidity .......................................................................................................... 4
Installation Space ............................................................................................................................. 4
2. Included Items...........................................................................................5
3. About the Symbols ....................................................................................7
4. Assembling and Installing..........................................................................8
Assembling and Installing............................................................................................................. 8
5. Connecting the Cables............................................................................18
Connecting the Cables.................................................................................................................18
6. Filling with Ink..........................................................................................20
Filling with Ink for the First Time...............................................................................................20
7. Network Settings .....................................................................................30
Step 1: Make the Network Settings for the Computer......................................................30
Step 2: Make the Network Settings on the Machine .........................................................32
Step 3: Make the Port Settings for the Software RIP..........................................................33
8. When Moving the Machine......................................................................34
Procedures from Preparing to Move Through Reinstalling.............................................34
3
1. Installation Environment
Deciding on an Installation Site
Install in a quiet, stable location oering good operating conditions. An unsuitable location can cause accident,
re, faulty operation, or breakdown.
WARNING Install the machine in a location that is level, stable, and able to bear the
weight of the machine.
The total weight may reach over 235 kg (518 lbs). Installation in an unsuitable
location may cause a major accident, including tip over, fall, or collapse.
WARNING Never install out of doors or in any location where exposure to water or
high humidity may occur.
Current leakage may cause electrical shock, electrocution, or combustion and
re.
WARNING Never install close to any ammable object or in a gas-lled location.
Combustion or explosion may be a danger.
WARNING Install in a clean, brightly lit location.
Conduct operations in a clean, brightly lit location. Working in a location that
is dark or cluttered may lead to an accident, such as becoming caught in the
machine as the result of an inadvertent stumble.
WARNING Position so that the power plug is within immediate reach at all times.
This is to enable quick disconnection of the power plug in the event of an emer-
gency. Install the machine next to an electrical outlet. Also, provide enough
empty space to allow immediate access to the electrical outlet.
CAUTION Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard or danger of com-
bustion due to ink fumes.
Unsuitable Installation Sites
Locations subject to large uctuations in temperature or humidity
Locations subject to shaking or vibration
Locations where the oor is tilted, not level, or unstable
Dusty locations
Locations exposed to direct sunlight
Locations exposed to direct near air-conditioning or heating equipment
Locations exposed to water or moving air
Locations exposed to considerable electrical or magnetic noise, or other forms of electro-
magnetic energy
1. Installation Environment
4
Temperature and Humidity
Maintain the specied temperature and humidity even when the machine is not in use. If temperatures are
too high or too low, it may cause malfunction.
Installation Space
The space shown in the gure is required in order to use this machine.
During operation:Temperature 20 to 32˚C (68 to 90˚F), relative humidity 35 to 80% (no condensation)
During non-operation: Temperature 5 to 40˚C (41 to 104˚F), relative humidity 20 to 80% (no conden-
sation)
3600mm (141.8in)
800mm (31.5 in)
2600mm (102.4 in)
Machine Space
Work Space
2000mm (78.8in)
5
2. Included Items
The following items are packed together with the machine. Make sure they are all present and accounted for.
Power cord (1) Arms (one for right and
left each) Casters (2) Stand legs (one for
right and left each)
Stand stay (1) Shafts (2)
Shaft clamps (2) Bolts (38) Hexagonal wrench (1) Pipe (1)
Cable clamp (1)
Media holders / Media
holder retaining screws
(one for right and left each)
Media clamps*(one for
right and left each) Cleaning liquid (1)
Cleaning sticks Replacement blades for
separating knife (1) Drain bottles (2) SOL INK cleaning car-
tridges (2)
Tweezers (1) Replacement wiper (1) Replacement felt wiper
(1)
RIP&PRINT MANAGE-
MENT SOFTWARE (1)
2. Included Items
6
User's Manual (1) Read this rst. (1) INKJET PRINTER MAIN-
TENANCE GUIDE (1)
7
3. About the Symbols
The meanings of the symbols used in this document are as follows.
The symbol indicates things that must be followed in relation to operation.
Always follow these instructions to prevent accident or damage due to misop-
eration.
The symbol indicates things that must be checked visually in relation to op-
eration. Always perform a visual check to prevent accident or damage due to
failure to check.
The symbol indicates "additional information".
8
4. Assembling and Installing
Completed drawing
About the picture
Assembling and Installing
WARNING Perform this task with all power switches left switched off.
Otherwise sudden movement of the machine may cause injury.
CAUTION Unpacking and installation must be carried out by six or more personnel.
Otherwise the machine or the stand may fall, resulting in injury.
Necessary tool (Included items)
Tighten temporary
Hexagonal Wrench
Tighten fully
Pipe
(Use this pipe if the hexagonal wrench is
too short to tighten the bolt)
4. Assembling and Installing
9
1.
Assemble the stand.
When tightening the bolts fully, tighten them securely. Loose bolts may cause the stand
to wobble.
4. Assembling and Installing
10
w
x
View from right above
Autres manuels pour VersaEXPRESS RF-640
3
Table des matières
Autres manuels Roland Traceur
Roland
Roland VT-200 Manuel utilisateur
Roland
Roland TrueVIS VG-640 Manuel du propriétaire
Roland
Roland DXY-800 Manuel utilisateur
Roland
Roland VersaUv LEF - 12i Manuel utilisateur
Roland
Roland DXY-1300 Manuel d'installation
Roland
Roland LEC-300 Manuel utilisateur
Roland
Roland SOLJET PRO4 XF-640 Manuel utilisateur
Roland
Roland Camm-1 CX-24/12 Manuel utilisateur
Roland
Roland VS-640 Manuel d'utilisation et d'entretien
Roland
Roland VP Series Manuel utilisateur
Roland
Roland Camm-1Pro Series Manuel utilisateur
Roland
Roland LEF-300 Manuel utilisateur
Roland
Roland SP-300 Manuel utilisateur
Roland
Roland DPX-3300 Manuel utilisateur
Roland
Roland VersaCamm VP-540 Manuel d'utilisation et d'entretien
Roland
Roland VersaEXPRESS RF-640 Manuel utilisateur
Roland
Roland CAMM-1 PRO CM-500 Manuel d'utilisation et d'entretien
Roland
Roland VersaUV LEF-200 Instructions de fonctionnement
Roland
Roland Camm-1 GR2-640 Manuel utilisateur
Roland
Roland VersaUv LEF - 12i Manuel utilisateur
