Robustel GoRugged R2000 Manuel utilisateur

Hardware Installation Quick Guide

R2000 Dual--

Industrial Dual Module Cellular VPN Router with

Power over Ethernet

Package Contents

Before installing the R2000 Dual Router, verify the kit contents as following:



1 x Robustel R2000 Dual Industrial Dual Module Cellular VPN Router with Power over Ethernet

1 x Terminal block for power

1 x Quick Start Guide with download link of other documents or tools

Optional Accessories (sold separately)

AC/DC power adapter

POE power adapter

SMA cellular antenna for 3G/4G LTE

Stubby/magnet RP-SMA Wi-Fi antenna

Wall mounting kit

35 mm DIN rail mounting kit

*If any of the above items is missing or damaged, please contact your Robustel sales

representative*

Environmental Requirements

Power input: 9 to 48V DC

Power consumption: 100 mA@12 V in idle state;

800 mA (peak)@12 V in communication state

Operating temperature: -40 to 70°C

Relative humidity: 5 to 95% RH

Reset Button

Reboot: Press and hold the Reset button for at least 2~7 seconds under the operating status.

Restore to factory default settings: Wait for 5 seconds after powering up the router, press and hold

the Reset button by a small non-conductive stick with a blunt end until all twelve LEDs blinking one by

one, and release the button within 5 second to return the router to factory defaults.

Ethernet Ports

R2000 Dual Router has five Ethernet ports. Eth0 is a WAN port and Eth1~Eth4 are LAN ports

supporting POE feature.

Every Ethernet port has two LED indicators, while each indicator has three states. The yellow one is

Link Indicator and the green one doesn’t mean anything. For details see the table below:

Indicator

State

Description

Link Indicator

Connection is working

On, blinking

Data is being transmitted

Off

Connection is not working



Device should be in accordance with the

reliable grounding to avoid lighting

strike.

Use the rated power adapter for the

device, and note the power polarity

when wiring.

Pay attention to waterproof in storage,

transporting and operating environment.

Place the device on the horizontal

surface.

Damaging the product’s warranty

labeling cannot enjoy the free

maintenance in warranty period.

CAUTION！

Hardware Introduction

Overview

Hardware Installation

Step 1: After opening the package, refer to the following figure to insert the SIM into the router.

Note: Recommended torque for inserting is 0.5 N.m, and the maximum allowed is 0.7N.m.

Step 2: Attach the SMA external antenna to the router’s antenna interface and twist tightly.

Make sure the antenna is within the correct frequency range

Note: Recommended torque for mounting is 0.35 N.m.

Step 3: Connect the router to the site ground wire by the ground screw before powering on (Optional) .

Step 4: Connect the router’s Ethernet port (Eth0/Eth1/Eth2/Eth3) to a PC via a standard cross-over cable.

Step 5: The router supports flat surface placement, wall mounting and DIN rail mounting.

Wall mounting:

Use 4 pcs of M2.5*4 flat head Phillips screws to fix the wall mounting kits to the router, and then

use 2 pcs of M3 drywall screws to mount the router associated with the wall mounting kit on the

wall.

Note: Recommended torque for mounting is 0.5 N.m and the maximum allowed is 0.7 N.m.

Din rail mounting:

Use 3 pcs of M3*6 flat head Phillips screws to fix the DIN rail to the router, and then hang the DIN

rail on the bracket. It is necessary to choose the standard bracket.

Note: Recommended torque for mounting is 1.0 N.m, and the maximum allowed is 1.2 N.m.

Step 6: R2000 Dual Router supports reverse polarity protection, but always refers to the figure below to

connect the power adapter correctly. There are two cables associated with the power adapter.

Following to the color of the head, connect the cable marked red to the positive pole through a

terminal block, and connect the yellow one to the negative in the same way.

LEDs

Name

Color

State

Description

RUN

Green

On, 1/2 sec blink

Router is ready

On, 1 sec blink

Router is booting

Off

Router is powered off

PPP

Green

LED 1 is on

SIM1 PPP connection is working

LED 2 is on

SIM2 PPP connection is working

USR

Green

OpenVPN: OpenVPN is connected

IPsec: IPsec is connected

Wi-Fi: Wi-Fi is connected

Off

OpenVPN: OpenVPN is disconnected

IPsec: IPsec is disconnected

Wi-Fi: Wi-Fi is disconnected

NET

(LED 1 stands for

SIM 1, LED 2

stands for SIM 2)

Green

On, blinking green

Unable to connect to the best network.

E.g. When R2000 Dual uses the 4G SIM card but

cannot connect to the 4G network, the NET LED

will always blink. The condition of 3G and 2G

network will, too.

On, solid green

Connect to the best network.

E.g. When R2000 Dual uses the 4G SIM card

and connects to the 4G network, the NET LED

will turn to solid green. The condition of 3G and

2G network will, too.

Off

Unable to access any network.

Signal Strength

(Light 1 stands

for SIM 1, light 2

stands for SIM 2)

Green

All LEDs are on

Signal level: 21-31 (Optimum signal level)

Green

Two LEDs are on

Signal level: 11-20 (Average signal level)

Green

Only one LED is on

Signal level: 1-10 (Abnormal signal level)

When the network disconnected, those three signal LEDs are designed as a

binary combination code to indicate a series of error report

On: 1 Off: 0

001 AT command failed

010 no SIM card detected

011 it need to enter the PIN code

100 it need to enter the PUK code

101 registration failed

110 something wrong happened in the module

Insert SIM card

Wall mounting

DIN rail mounting

E-mail: [email protected]

Note: The range of power voltage is 9 to 48V DC.

Step 7: R2000 Dual Router also supports POE feature. Please refer to the figure below to

connect the power adapter correctly.

Note: The range of power voltage is 48 to 57V DC.

POE Connection

(OPTIONAL)

R2000 Dual’s four fast Ethernet LAN ports support POE feature (Voltage range: 48 to 57V DC), which

can electrify the network terminal devices such as IP camera and other WLAN AP etc. See figure below

for more details.

Autres manuels pour GoRugged R2000

Table des matières

Autres manuels Robustel Routeur réseau

Robustel

Robustel GoRugged R3000-3P-GPS Manuel utilisateur

Robustel

Robustel GoRuggedR 3000 Manuel utilisateur

Robustel

Robustel R3000-3P Manuel utilisateur

Robustel

Robustel GoRugged R3000 Lite Guide de l'utilisateur

Robustel

Robustel GoRugged R2000 Manuel

Robustel

Robustel R3000 Quad Manuel utilisateur

Robustel

Robustel R3000-Q3PA Manuel utilisateur

Robustel

Robustel R1510 Manuel utilisateur

Robustel

Robustel GoFixed W800 Manuel utilisateur

Robustel

Robustel GoRugged R2000 Manuel utilisateur

Robustel

Robustel GoRugged R2000 Manuel utilisateur

Robustel

Robustel GoRugged R3000 Lite Manuel utilisateur

Robustel

Robustel GoRugged R2000 Manuel de l'opérateur

Robustel

Robustel GoRugged R3000 Lite Manuel utilisateur

Robustel

Robustel R1511 Manuel utilisateur

Robustel

Robustel GoRugged R3000 Lite Instructions d'utilisation et d'entretien

Robustel

Robustel R5020 Manuel utilisateur

Robustel

Robustel EV8100 Manuel utilisateur

Robustel

Robustel R2110 Manuel utilisateur

Robustel

Robustel EG5200 Manuel utilisateur

Robustel

Robustel R1500 Manuel utilisateur

Robustel

Robustel GoRugged R3000 Lite Mode d’emploi

Robustel

Robustel R1520 Manuel utilisateur

Robustel

Robustel R5010 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité