Riva RC3702HD-5314 Manuel utilisateur

www.rivatech.de

Quick Installation Guide

This manual provides instructions for quick installation and basic configuration of your IP device.

www.rivatech.de

Step1. Connect cables to IP device

Connect required cables to the device including the power cable and LAN cable. To see the

correct positions of all connectors, refer to the following image below.

Make sure the polarity is correct. Incorrect connection may

cause malfunction or damage to the IP device.

Caution

Power Adaptor Connector (DC

12V)

Output Configuration Switches

RED : POWER +

BLACK : POWER -

YELLOW : AUDIO IN

BLUE : AUDIO GND

GRAY : DI COM

BROWN : DO COM

ORANGE : DO

GREEN : DI

PURPLE : GND

WHITE : AUDIO OUT

ETHERNET

LAN Cable

Audio, DI, DO Terminal

Power Cable

* Model design and appearance are subject to change without any prior notice

PAL/NTSC Button

* Video out is used

only for installation

and works for 3

minutes when

PAL/NTSC button is

pushed.

www.rivatech.de

Step2. Install IP device

To prevent products from damaging, place the camera on stable and non-

vibrating surfaces. If the stability is in doubt, consult with safety personnel for

reinforcements, and then proceed with the installation.

Caution

1) Place the installation template (paper)

that is included in the package on the

desired installation surface.

2) Drill three holes in correct positions

based on the template paper, and insert

anchor blocks into the holes.

3) When placing the camera body to the

installation surface, match three

alignment holes with three anchor

blocks.

4) Tighten the surface anchor studs.

5) Connect all the required cables to the

camera.

6) Adjust the lens position. Detailed

information can be found in 3. Set the

Lens Position.

7) Place the dome cover on the main

body of the camera. Dome cover has

three alignment holes that match

camera body’s alignment holes.

8) Once properly placed, insert hex

screws into the three holes of the body

and tighten them up with hex wrench

driver.

www.rivatech.de

Step3. Set the lens position

1) Remove the dome cover to control the positioning buttons, or use web site setup (Setup >

Video & Audio >Repositioning) to adjust the camera.

2) Positioning buttons are located on the main body. To pan, use ‘+’ and ‘–‘pan buttons. To tilt,

use ‘+’ and ‘-‘tilt buttons.

Even though the camera can pan 355

degrees, the recommended “default” front

of the camera housing is described on a

right figure.

Please refer to the diagram below for the

proper camera housing position and the

camera lens:

B. Pan the lens with

pan ‘+’ and ‘-‘ buttons

A. Tilt the lens with

tilt ‘+’ and ‘-‘ buttons

PAN & TILT buttons

www.rivatech.de

Lifespan of PAN and TILT are approximately good up to 5,000 counts each.

Operating temperature ranges for PAN and TILT are 10˚C ~ 40 ˚C (50˚F ~

104˚F)

Step4. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of

the device from converting the MAC address’s hexadecimal numbers, which is attached to the

device. Be sure that the device and PC are on a same area network before running the

installation.

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are

used, users may view the live streaming images on a web page using the device’s default IP

address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal

Conversion Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2. Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.

3. Web streaming and device configurations are supported through ActiveX program. When

the ActiveX installation pop-up window appears, authorize and install the ActiveX setup.exe,

Caution

MAC address = 00-13-23-01-14-B1 →IP address = 192.168.20.177

Convert the last two set of hexadecimal numbers to decimal numbers.

www.rivatech.de

Custom IP Environment

IPAdminTool and the manual are provided on www.rivatech.de homepage.

IPAdminTool is a management tool, which automatically scans all of the network products for

users to perform administrative tasks, which includes network configurations, firmware update,

device reboot, and device organizations.

To modify the device’s default IP address for customized network area;

1. Find the device from the IPAdminTool’s list and highlight the device’s name.

2. Right-click the mouse and select “IP Address”; IP Setup window appears.

www.rivatech.de

3. In the IP Setup’s window, information under ‘Local Network information’ displays the

user/PC’s network area information. Those information need to be incorporated to

the IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP

Address, which are to be the unique numbers for the device. Refer to the image

above for the setting

4. Click ‘Setup’ to complete the modification. When the dialog box appears to request

user name and password, enter the default value for the administrator account (case-

sensitive)

ID:

root

Password:

pass

Step5. View video on web page

Once the device has the proper IP address, users can view the live streaming images

through a web browser. The default username and password is

root / pass

PC environment Info

Give new unique IP address in

last two sets and mirror other

information in other boxes

www.rivatech.de

1. When the device’s web address is accessed, the browser asks to install the

ActiveX. Click Allow.

2. Setup.exe installation link or pop-up window appears, depends on Microsoft®

Internet Explorer version. Proceed with rest of setup installation.

3. Follow the instructions of the dialog boxes and complete the installation. Once the

installation is complete, start the web browser again and check if video stream is

displayed in the main view frame.

Depends on system OS and Internet Explorer version, Installation experience may

differ from one another. Figures described above are from Windows 7, Internet

Explorer 9 environment.

Note

www.rivatech.de

Rebooting

Perform the following procedures to reset your device:

1. Press the Reset button for 2 seconds.

2. When the power LED turns to red, wait for the system to reboot.

Resetting to the Factory Default Settings

Resetting the device back to the factory default will initialize all parameters including the IP

address back to the factory defaults. To reset back to the factory default;

1. Press reset button and hold for 5 seconds..

2. Release the button when the green Power LED blinks at 150ms interval.

3. The power LED button turns to red and wait for the system to reboot.

The factory default settings can be inferred as follows:

More Information

To learn more about using other features of your devices, refer to the manuals as “RIVA

Web Interface Manual Full HD Series” or “VCAsys Online Help”, which is available on

www.rivatech.de homepage.

IP address: 192.168.xx.yy

Network mask: 255.255.0.0

Gateway: 192.168.0.1

User ID: root

Password: pass

www.rivatech.de

Hexadecimal-Decimal Conversion Table

Refer to the following table when you convert the MAC address of your device to IP address.

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

111

148

185

222

112

149

186

223

113

150

187

224

114

151

188

225

115

152

189

226

116

153

190

227

117

154

191

228

118

155

192

229

119

156

193

230

120

157

194

231

121

158

195

232

122

159

196

233

123

160

197

234

124

161

198

235

125

162

199

236

126

163

200

237

127

164

201

238

128

165

202

239

129

166

203

240

130

167

204

241

131

168

205

242

132

169

206

243

133

170

207

244

134

171

208

245

135

172

209

246

136

173

210

247

100

137

174

211

248

101

138

175

212

249

102

139

176

213

250

103

140

177

214

251

104

141

178

215

252

105

142

179

216

253

106

143

180

217

254

107

144

181

218

255

Autres manuels pour RC3702HD-5314

Table des matières

Autres manuels Riva Caméra de sécurité

Riva

Riva RC3500 Manuel utilisateur

Riva

Riva RC3502HD-5311 Manuel utilisateur

Riva

Riva RC4602HD-6416 Manuel utilisateur

Riva

Riva IPX5502HD-6415-05 Manuel utilisateur

Riva

Riva RC362HD-6211IR Manuel utilisateur

Riva

Riva RC5510 Manuel utilisateur

Riva

Riva RC3202HD-6111 Manuel utilisateur

Riva

Riva RC3102HD-5211 Manuel utilisateur

Riva

Riva RC3502HD-5211 Manuel utilisateur

Riva

Riva RC3202HD-6111W Manuel utilisateur

Riva

Riva RC4602SV01-2017-A Manuel utilisateur

Riva

Riva RC4602SV-7416A-30 Manuel utilisateur

Riva

Riva RC3402HD-6311IR Manuel utilisateur

Riva

Riva RC3202HD-6111 Manuel utilisateur

Riva

Riva RC3502HD-5311IR Manuel utilisateur

Riva

Riva RC8102HD-6111T Manuel utilisateur

Riva

Riva RC3502HD-5311IR Manuel utilisateur

Riva

Riva RC3500M Manuel utilisateur

Riva

Riva RC3402HD-6211IR Manuel utilisateur

Riva

Riva RC3402HD-6311 Manuel utilisateur

Riva

Riva RC3502HD-5311 Manuel utilisateur

Riva

Riva RC4202HD Manuel utilisateur

Riva

Riva RC100 Manuel utilisateur

Riva

Riva RC4100-IN Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur