Ritetemp 6008 Manuel utilisateur

Install Guide 6008

Location

Caution

Tools

To avoid electrical shock and to prevent damage to the furnace, air conditioner,

and thermostat, disconnect the power supply before beginning work.

This can be done at the circuit breaker, or at the appliance.

C A U T I O N

Your thermostat is a precise instrument.

Please handle it with care.

Turn off electricity to the appliance before installing or

servicing thermostat or any part of the system. Do not

turn electricity back on until work is completed.

Do not short (jumper) across electric terminals at

control on furnace or air conditioner to test the system.

This will damage the thermostat and void your warranty.

All wiring must conform to local codes and ordinances.

This thermostat is designed for use with 24 volt AC and

millivolt systems. The thermostat should be limited to a

maximum of 1.0 amps; higher amperage may cause

damage to the thermostat.

On replacement installations, mount the new thermostat in place of the

old one if possible.

On new Installations, follow the guidelines listed below.

Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the

floor, and in a room that is used often.

Do not install it where there are unusual heating conditions, such as: in

direct sunlight; near a lamp, radio, television, radiator register, or

fireplace; near hot water pipes in a wall; near a stove on the other side

of a wall.

Do not locate in unusual cooling conditions, such as: on a wall separating

an unheated room; or in a draft from a stairwell, door, or window.

Do not locate in a damp area. This can lead to corrosion that will shorten

thermostat life.

Do not locate where air circulation is poor, such as: in a corner or an

alcove; or behind an open door.

Do not install the unit until all construction work and painting has been

completed.

This thermostat does not require leveling.

You will need #1 Phillips screwdriver (small) and

Drill with 3/16-in. (4.8mm) bit for this installation.

Good

5ft.

(1.5m)

Install Guide 6008

Remove old unit

Label Wires to Old Unit

Mount the 6008

Separate front from back of unit. Grasp the front of the

unit and the back of the unit and pull apart. The

thermostat body away from the base.

Hold the base against the wall, with the wires coming

through the opening below the terminal block.

Position the base for best appearance

The 6008 can be mounted vertically or horizontally.

chose the position that best suites your wall.

Attach the base to the wall with the two screws

provided.

If you are mounting the base to sheet rock or if

you are using the old mounting holes, use the

plastic anchors provided.

Drill a 3/16-in.(4.8mm)

hole for the insert at

each screw location,

then mount the base.

4 Terminal Block

Wires in wall come from

Furnace and AC unit

Switch electricity to the furnace and air conditioner OFF;

then proceed with the following steps.

Remove cover from old thermostat. Most are snap-on types and simply pull

off. Some have locking screws on the side or front. These must be loosened.

Note the letters printed near the terminals.

Carefully attach labels (enclosed) to each wire.

Label the wires one at a time.

You must have all the wires labeld before you procede.

Remove the wires from the terminals of the old thermostat.

Make sure the wires do not fall back inside the wall.

Wind them around a pencil to keep them from falling.

Remove the old thermostat from the wall. Fill wall

opening with fiber glass insulation to prevent drafts.

Caution

DO NOT REMOVE WIRES FROM OLD THERMOSTAT UNTIL YOU HAVE

CAREFULLY LABELED THEM, WITH LABELS PROVIDED.

THERE IS NO STANDARD COLOR CODE FOR THESE WIRES.

Before you Connect Wires

Caution

Do not allow wires to touch each other or parts on thermostat.

Wires must be routed through the hole in the back plate, below the

terminal block, or they will hit parts on the cover.

Please follow these guidelines for safe and secure wire connections.

Determine which step-by-step wiring diagram you should use. Make sure your

wires are labeled. This may require you to find the 'other end' connection for each

wire on your heating or airconditioning equipment and read the label there.

If you have a wire maked "C" its connection is optional. If you do connect it the

thermostat will draw power from the C wire and this will extend battery life.

Optional Wire Connections

What Wires Do you Have?

Strip insulation 3/8 in. (9.5mm) from wire ends.

Take care not to damage the labels for each wire in handling.

Connect labeled wires only to a terminal with corresponding letter.

Bend the wire slightly, insert the wire under the contact plate and

tighten the screw down onto the wire.

PG 6

From Furnace

And AC unit

From Furnace

And AC unit

Go To Page 13 Go To Page 14

Go To Page 12

From Furnace

Go To Page 11

R - Single source power for heat/cool

Note: R connects to both RC and

RH using the Orange jumper

RH or 4 - HEATING POWER

RC - COOLING POWER

W - HEATING CONTROL

G - FAN RELAY

C - Common side of Heating Power

Y - COMPRESSOR

O - If you have this wire the 6008 will

not control your system.

B - If you have this wire the 6008 will

not control your system.

or R

When you have finished making connections.

Re-attach the the body onto the base by

pressing it firmly onto the base.

Install Batteries

Wiring complete

Check Unit

The 6008 requires 2AA batteries if the C-wire

is not available in your furnace installation.

Switch MODE switch to OFF and

the FAN switch to AUTO.

Remove the control unit form the wall unit.

Install 2 AA alkaline batteries according to the polarity noted

in the compartment.

(DO NOT USE Rechargable Batteries)

NOTE: Replace the batteries when the red LOW battery LED

indicator blinks or once a year.

Caution: The thermostat will go "off" if the batteries die. This exposes

your house to unexpected heat or cold and should be avoided.

Follow these procedures to verify you have correctly installed the unit.

To check Fan: (If you connected the G wire - fan relay)

Switch the FAN switch to the ON position.

Verify that air is blowing from the system.

Return to AUTO position for normal operation.

To check HEAT mode:

Set the mode switch to HEAT. Set the fan switch

AUTO.

Turn TEMP DIAL counter clockwise to its stop.

Allow the system 5 min to respond.

Verify that heat is blowing from the system.

To check COOL mode:

Turn TEMP DIAL clockwise to its stop.

Allow the system 5 min to respond.

Verify that cool air is blowing from the system.

PG 7

PG 8

GAS

ELECT

Temperature

Dial

HEAT/COOL

Mode Switch

Fan

Switch

Note:

If you have electric heat, turn the

thermostat over

and find the GAS/ELECTRIC heat

selector on the back of the control

unit(see diagram below). Move the

selector jumper to the ELECT

position.

1) The 6008 can run on batteries only. (2AA Alkaline)

The batteries will last well over 1 year. If the batteries are not replaced the

thermostat will stop working.

2) The 6008 can run on the C wire if available.

24VAC ONLY

As shown in the wiring diagrams, The C wire is the other side of the 24VAC

heating transformer. If the C wire is used, the batteries are not needed.

Power Options

Check Unit cont.

Congratulations, you have successfully installed your unit. Please

proceed to the OPERATING Guide to initialize the new thermostat.

PG 9

PG 10

Gas/Electric jumper

GAS

ELECT

PG 11

PG 12

STEP 1 - Connect the R(or RH) wire to

the RH terminal on the thermostat.

This connects the Heater Power to the

thermostat.

STEP 2 - Connect the Wwire to the Wterminal

on the thermostat.

This connects the heater control line to the thermostat.

Your Heater is now concected to the thermostat.

STEP 1 - Connect the R(or RH)

wire to the RH terminal on the

thermostat. This connects to the

Heater Power .

STEP 2 - Connect the Wwire to the

Wterminal on the thermostat.

This connects the heater control line to

the thermostat.

STEP 3 - Connect the Gwire to the G

terminal on the thermostat.

This connects the Fan to the thermostat.

Your system is now conected to the thermostat.

Return To Page 7

2 WIRE Heating

(GAS MILLIVOLT or 24vac

NOTE: Wires marked with the dotted line are optional.

3 WIRE

FURNACE

jumper

wire

Heat

Power Heat

W G

FAN

Thermostat

jumper

wire

FURNACE

HEAT

Thermostat

HEAT

Power

From Furnace

or R

PG 14

PG 13

From Furnace

and AC unit

From Furnace

and AC unit

STEP 1 - Connect the Y wire to the

Yterminal on the thermostat. This

connects to the Cooler compressor.

STEP 2 - Connect the RH or Rwire

to the RH terminal on the thermostat.

This connects the Heater/Cooler

Power.

STEP 3 - Connect the Wwire to the Wterminal on the

thermostat. This connects to the heater control line.

STEP 4 - Connect the G wire to the Gterminal on the

Thermostat. This connects to the Fan.

Your HVAC system is now conected to the thermostat.

STEP 1 - Remove the orange

Jumper wire.

STEP 2 - Connect the Y wire to

the Yterminal on the thermostat.

This connects to the Cooler

compressor.

STEP 3 - Connect the RH wire to the RH

terminal on the thermostat. This connects to the

Heater Power .

STEP 4 - Connect the RC wire to the RC terminal on

the thermostat. This connects to the Cooling Power .

STEP 5 - Connect the Wwire to the Wterminal on the thermostat.

This connects to the heater control line.

STEP 6 - Connect the G wire to the Gterminal on the Thermostat.

This connects to the Fan.

Your HVAC system is now conected to the thermostat.

Return To Page 7

5 WIRE

4 WIRE

NOTE: Wires marked with the dotted line are optional.

HVAC SYSTEM

jumper

wire

Heat

Power Heat

FAN

Cool

Comp

Thermostat

HVAC SYSTEM

Remove

jumper

wire

HEAT

Power

Heat

RHRC

FAN

Cool

Comp

COOL

Power

Thermostat

6008 Features

PG 15

The 6008 can be used with most 24 volt gas, oil or electric

heating and air conditioning systems, or gas millivolt heating

systems. It cannot be used with 120 volt heating systems or heat

pump systems. Ask The Home Depot for other thermostats to

control those systems.

The 6008 is digital. You can program your desired Heat and cool

temperature by setting the dial. The unit uses no harmful mercury.

A 5-minute minimum off time in COOL protects your air

conditioning system from being damaged.

Two "AA" batteries (not included) are used to run the thermostat

in some installation. "C" wire installations require no batteries.

1611-013

Customer Support: 877-505-2353

or Visit our website www.ritetemp-thermostats.com

Autres manuels pour 6008

Table des matières

Autres manuels ritetemp Thermostat

ritetemp

ritetemp 8010 Manuel utilisateur

ritetemp

ritetemp 8085 Manuel utilisateur

ritetemp

ritetemp 8050 Manuel utilisateur

ritetemp

ritetemp 6036 Manuel utilisateur

ritetemp

ritetemp 8050C Manuel utilisateur

ritetemp

ritetemp 8046 Manuel utilisateur

ritetemp

ritetemp 6025 Manuel utilisateur

ritetemp

ritetemp 8029B Manuel utilisateur

ritetemp

ritetemp 8085c Manuel utilisateur

ritetemp

ritetemp 8046 Manuel utilisateur

ritetemp

ritetemp 8025 Manuel utilisateur

ritetemp

ritetemp 8029B Manuel utilisateur

ritetemp

ritetemp 8030 Manuel utilisateur

ritetemp

ritetemp 8022 Manuel utilisateur

ritetemp

ritetemp 8025 Manuel utilisateur

ritetemp

ritetemp 6010 Manuel utilisateur

ritetemp

ritetemp 6005 Manuel utilisateur

ritetemp

ritetemp 8099 Manuel utilisateur

ritetemp

ritetemp 8035C Manuel utilisateur

ritetemp

ritetemp 6025 Manuel utilisateur

ritetemp

ritetemp 8082C Manuel utilisateur

ritetemp

ritetemp 8030C Manuel utilisateur

ritetemp

ritetemp 6005 Manuel utilisateur

ritetemp

ritetemp 8022 Mode d’emploi

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur

ritetemp 6008 Manuel utilisateur

Manuels Thermostat populaires d'autres marques