Risco WL X312 Manuel utilisateur

Italiano

Nederlands English

Português Français Español

Two Way Wireless PIR Outdoor Detector

Rivelatore PIR da esterno via radio bidirezionale

Detector de Exterior PIR Inalámbrico Bidireccional

Détecteur extérieur PIR sans fil à communication bidirectionnelle

Detector Externo de Infravermelho Passivo sem fio Bidirecional

Draadloze PIR buitendetector met bidirectionele communicatie

WL X312

Installation Instructions

Istruzioni per l’installazione

Manuel d'installation

Instrucciones de Instalación

Instruções para Instalação

Installatie handleiding

Installation Manual

Installation Manual 3

English

WL X312 - Two Way Wireless PIR Outdoor

Detector

Table of Contents

Installation.............................................................................................................................. 4

Introduction............................................................................................................................ 4

Mounting ................................................................................................................................ 4

Mounting Considerations..................................................................................................... 4

Wall Mount Installation.........................................................................................................6

Flat Mounting....................................................................................................................... 6

45° angle Mounting (Left side mounting).............................................................................. 6

Changing Back Tamper position.......................................................................................... 7

Back Tamper Terminal Wiring............................................................................................... 7

Configuration Parameters..................................................................................................... 7

Detection Length Adjustment ............................................................................................... 8

Walk test................................................................................................................................. 9

LEDs Display.......................................................................................................................... 9

Operational Modes................................................................................................................. 9

Transmitter/Receiver Communication link setup ................................................................ 9

Standard Swivel Installation (Optional).............................................................................. 10

Wall Mounting.................................................................................................................... 10

Replacing Lenses ................................................................................................................12

Technical Specification....................................................................................................... 13

Ordering Information........................................................................................................... 13

Accessory Kits..................................................................................................................... 13

4 Installation Manual

Installation

Introduction

RISCO Group's WL X312 is a unique detector with signal processing based on two Passive Infrared

(PIR) channels. The WL X312 has an adjustable detection range. The detector is compatible with the

RISCO Agility panel.

The following instructions describe the installation of the WL X312.

Mounting

Mounting Considerations

1. Installation Height: 0.8m - 1.2m

(2'8" – 3'11")

Typical Installation Height: 1m (3'3")

2. To ensure maximum operational reliability, install the detector perpendicular to the ground so

that the upper detection area is parallel to the ground.

3. For optimum detection,

select a location that is likely

to intercept an intruder

moving across the coverage

pattern.

4. Avoid pointing the detector to moving

objects (swaying trees, bushes etc.)

Out of

Detection Range

With moving objects

keep distance of

minimum 5 meters (16')

5m (16')

5. Ensure any objects do not obstruct the field

of view. Pay attention to growing trees or

bushes, plants with big moving leaves etc.

Installation Manual 5

English

Installing the WL X312 detector in challenging situations

In the following situations, rapid and significant infrared radiation changes can happen in both

PIR channels together, resulting in false alarms and therefore care should be taken.

1. Situations in which metal and/or glass objects measuring over 70cm (2’4”) in height from the

ground are in the field of view of the detector (cars, metal gates, shutters, metal walls,

windows, etc.)

2. Situations in which a reflective surface on the ground larger than 1m (3’4”) in diameter may

cause reflection into the detector’s lens. Examples of a reflective surface on the ground are a

puddle, wet road or car park, smooth concrete or asphalt surface, swimming pool, etc.

Water Reflection

NOTES:

1. Please note that any outdoor PIR detector will require reduction in range to a shorter distance than the car, metal

object or surface reflection (so that these objects won’t be protected) in order to eliminate false alarms.

2. For full 15m (50’) coverage in the above situations, it is highly recommended to install the wired WatchOUT DT,

the only outdoor detector with 2 PIR channels and 2 Microwave channels.

3. Wireless WatchOUT detectors include high quality Silicon filters on the PIR sensors for blocking out white light

interferences. These filters are not intended to block infrared thermal radiation.

6 Installation Manual

Wall Mount Installation

Figure 1

Figure 2

Figure 3

Tamper

Lever

(not visible)

NOTE:

The installation knockouts numbering are marked

on the back plate.

1. Open the WL X312 front cover (unlock

C1, Figure 1).

2. Release internal base (unlock I1, Figure

2).

3. Select mounting installation as follows:

Flat Mounting:

Open knockouts on external base (Figure

3).

xB1 - B4: Wall mounting knockouts

xT1: Back tamper knockout

45° angle Mounting (Left side

mounting):

a. Open knockouts on external base

(Figure 3).

xL1, L2: Left mounting knockouts

xT3: Left tamper knockout

b. Remove tamper spring (Figure 4).

c. Replace tamper bracket (Item 1) with

supplied flat tamper bracket (Item 2).

Item 1 Item 2

d. Insert Tamper lever B onto T6 and T3

and secure screw A (Figure 3).

4. Secure external base to the wall.

5. Insert tamper wires through internal base

(Figure 4).

6. Secure internal base to external base

(lock I1, Figure 2).

7. Close the front cover (Lock C1, Figure 1)

after wiring and setting DIP switches.

8. Walk test the detector.

Figure 4

NOTE:

For 45° right side installation use the equivalent units on the external base as follows:

Knockouts Description Left Right

Mounting Knockouts L1, L2 R1, R2

Tamper spring knockouts T1,T3 T2,T4

Tamper screw anchor T5 T6

Installation Manual 7

English

Changing Back Tamper position:

The back tamper is by default secured on the right

side of the internal base (Rear view). If you wish to

move it to the left side (rear view), do the following

(Figure 5):

1. Remove tamper screw 1 in order to release the

tamper from position 7.

2. Ensure tamper spring (2) rests over tamper wire

base 4.

3. Ensure plastic tamper bracket (3) rests over

both 2 and 4.

4. Secure tamper screw (1) into (3) over position 6.

Figure 5 Left Side

Tamper

Right Side

Tamper

NOTES:

1. Verify that you hear a "Click" when attaching the tamper spring to the wall.

2. For pole installation, the tamper can be moved to the bottom right-hand side of the internal base.

Back Tamper Terminal Wiring

If you wish to use the back tamper (recommended) remove the short from the back tamper terminal

block and connect the back tamper wires to the back tamper terminal block.

Back Tamper in use

BACK TAMPER

Back Tamper not used

Short

H1 H1

Configuration Parameters

Via the Agility panel or Configuration Software you can define the following parameter settings of your

detector according to your needs:

1. LEDs operation

On: LEDs enabled (Default: On)

Off: LEDs disabled

2. PIR Sensitivity: High/Normal/Mid/Low (Default: Normal)

3. Mode: Normal/Walk Test (Default: Normal)

For more information refer to the Agility Installer Guide.

8 Installation Manual

Detection Range Adjustment

Slide the moving PIR to the desired

position, see figure 6.

The range of the lower detection area

determines the detection range.

The upper PIR is fixed and its detection

area is parallel to the ground at all times.

The lower detection area changes from

2m to 12m depending on the location of

the moving PIR. Therefore, the detection

range is established according to the

location of the lower PIR since both the

upper and the lower PIR should be

triggered in order to activate an alarm.

Figure 6

Detection patterns (side view): Detection range with 1m (3'3")

installation height:

* NOTE:

Length may vary according to

environmental thermal conditions.

Installation Manual 9

English

Walk test

Two minutes after applying power, walk test the protected area to verify proper operation.

Adjust the moving PIR for required detection range and reliability.

IMPORTANT!

Both upper and lower detection areas must be blocked simultaneously for detection to occur, see

figure 7 below.

Figure 7

LED Display

LED State Description

RED Steady Indicates ALARM

Operational Modes

Operational Mode Description

Normal Dead time (between detection alarms) is 2.5 Minutes.

Test (walk test) Dead time (between detection alarms) is 2.5 sec.

Write (for enrolling) The unit transmits a WRITE message each time both the Tamper

Switches (back and cover) are closed for at least 3 seconds.

NOTE:

After power up the detector enters into test mode for a period of 20 minutes (disregarding the DIP Switch Modes

Position).

Transmitter/Receiver Communication link setup

The detector must identify itself to the system’s receiver by writing its coded message into the

receiver’s address memory. This is accomplished by performing the following steps:

1. Set the receiver to Write Mode.

2. Remove the insulation material from the batteries and place them in the batteris holders on

the PCB on the right direction (pay attention to the "+" and "–" diagram on the PCB)

3. Send a WRITE message by closing both of the tamper switches (back and cover) for at least

3 seconds.

4. Verify that the detector has been identified by the receiver.

10 Installation Manual

CAUTION NOTICE

Changes or modifications not expressly approved by RISCO Group may void the user’s authority to

operate this equipment.

Simultaneous transmissions from two different units may cause message interference resulting in loss

of information.

The communication quality of this unit may be affected by its surrounding environment. Nearby

electrical equipment may interfere with its normal operation.

The operation of this unit must, therefore, be tested at each installation since its transmission quality

may vary as a result of operational conditions.

NOTE:

DIP Switch 1 should be in ON position to enable LED indications (regardless during the first 20 minutes after power

up).

Optional Swivel Installation (Not Supplied)

Please follow the instructions below for mounting the detector with the Swivel:

1. Open WL X312 front cover (Unlock C1, Figure 1).

2. Release internal base (Unlock I1, Figure 2).

3. Remove back tamper from the internal base (see the “Changing Back Tamper Position" paragraph

on page 7) and connect it to S5 (Figure 8, Detail A) on the Standard Swivel.

4. Select the mounting installation as follows:

NOTE:

Ensure that you see the engraved UP mark on the upper front face of the swivel.

Wall Mounting

1. Insert back tamper wires through the Swivel Wires Passage (Figure 8, Detail B).

2. Secure swivel to the wall through holes S1, S3, S6 and S8.

Detail B

Snaps

Detail C

S1 S2

Tamper

(see Detail C)

Detail A

Standard Swivel

Figure 8

3. Connect the external base to the swivel using the dedicated snaps (Figure 9).

Autres manuels pour WL X312

Table des matières

Langues :

Autres manuels Risco Capteur de sécurité

Risco

Risco BWareBus RK515DTBGL Manuel utilisateur

Risco

Risco Industrial LuNAR RK200DTG3 Manuel utilisateur

Risco

Risco iWave RWX95 Manuel utilisateur

Risco

Risco BWare BUS DT AM G3 Manuel utilisateur

Risco

Risco iREX Manuel utilisateur

Risco

Risco Digi-415DT Manuel utilisateur

Risco

Risco WiComm Pro Manuel d'instructions

Risco

Risco WatchU Manuel utilisateur

Risco

Risco iWISE QUAD AM Grade 3 Manuel utilisateur

Risco

Risco iWISE QUAD AM Grade 3 Manuel utilisateur

Risco

Risco Wireless ViTRON Manuel utilisateur

Risco

Risco Bware RWX515PR Manuel utilisateur

Risco

Risco WatchOUT Manuel utilisateur

Risco

Risco BWare BUS QUAD AM G3 Manuel utilisateur

Risco

Risco WL T6S Manuel utilisateur

Risco

Risco iWISE T92 Manuel utilisateur

Risco

Risco BWare RK515DTGL Manuel utilisateur

Risco

Risco iWISE RK815DTG3 Manuel utilisateur

Risco

Risco iWISE QUAD AM Grade 3 Manuel utilisateur

Risco

Risco iWAWE RWX95P Manuel utilisateur

Risco

Risco RK66S Manuel utilisateur

Risco

Risco WatchIN 325DT Manuel utilisateur

Risco

Risco WarchIN RK325DT Manuel utilisateur

Risco

Risco ShockTec Plus Grade 3 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur