Risco EL-5835D Manuel utilisateur

EL-5835D Wireless Outdoor DT

Detector

EL-5835DC Wireless Outdoor

DT CAM Detector

Installation Instructions

Model: EL-5835D / EL-5835DC

For more information about RISCO Group’s branches, distributors and full product line,

please visit riscogroup.com

Language Page

Description

The EL-5835D is a battery powered wireless DT detector that includes an integrated camera

(EL-5835DC model) for visual verification and has been designed to provide enhanced 24-hour

outdoor protection, with Active IR Anti-mask capabilities. Integrated Dual Technology (DT)

combines two K-band microwave channels with two PIR sensors for better catch performance and pet

immunity, minimizing false alarm.

Features include

 PIR coverage: 12m, 90°

 VGA or QVGA camera resolution with ~90° field-of-view

 Two channel K band - MW detection (Sway Recognition)

 Pet immunity

 Two correlated PIR Sensors

 Light sensor for reducing false alarms due to sunlight

 Active IR Anti mask

 Various mounting heights with optional swivel bracket

 Designed for outdoor installation, UV resistant, IP 65

 Cover and wall tampers

 3-axis-accelerometer for protection against vandalism

 Solar swivel for increased battery life (6+ years typically): EL-5835SL (optional)

What’s in the box

 EL-5835D Wireless DT Detector / EL-5835DC Wireless DT Camera Detector

 Screws Kit: 5 screws ø4.2x32 mm

 Installation Instructions

Applicable to EL-5835DC Model

Installation

Step 1: Preliminary Considerations

Select the mounting location for best coverage of the area that is to be protected (see Step 2: Coverage

Patterns). Pay attention to the following:

Figure 1

Install the device in a location where the detector’s field

of view is clear of any static obstacle

Figure 2

Walking direction must cut across the beam pattern

Up to 35cm

(1.1ft)

Figure 3

Do not install the device close to any moving objects

Step 2: Coverage Patterns

Figure 4

Step 3: Coverage

PIR Coverage

Mounting height [m] Distance [m]

1.8 10

2.2 (optimal) 12

Note For pet immunity, install the detector at the optimal height of 2.2 meters.

PIR Coverage - Using Swivel

Note The table below is relevant when using the Swivel/Solar Swivel Bracket (Model: EL-5835SL).

Mounting height [m] Swivel Angle [°] Distance [m]

1.8 010

5 7

10 5

2.2 (optimal) 012

5 8

10 6

2.5 – 2.7 0N/A

510

10 7

NA = Avoid such installation

Step 4: Registering/Deleting the Detector

Registration of the Detector in the System

The EL-5835 detector must identify itself to the panel’s receiver, as follows:

1. Set the system to registration mode.

a. Go to the main menu and select [9]>[1]>[1]

(Programming > Devices > Zones).

b. Select a zone and press '√'.

2. Open the detector housing.

3. Remove the battery from the detector, remove the battery’s plastic wrapping and then put back

the battery. When the LEDs stop blinking, the detector will send a transmission (Red LED is on).

If the transmission is successfully received by the system, it will play a confirmation sound. If no

confirmation sound is heard send another transmission by pressing and releasing the tamper

switch of the device.

4. As soon as 'Save?' appears press '√'; the Red LED flashes to indicate RSSI registration completion.

Quick Registration in the System (If Quick Registration is enabled)

1. At the control panel, press and hold for about 3 seconds (disregard the ENTER USER CODE

message) until QUICK REGISTR is displayed.

2. Open the detector housing.

3. Remove the battery from the detector, remove the battery’s plastic wrapping and then put back

the battery. The detector will send a transmission. If the transmission is successfully received by

the system it will play a confirmation sound. If no confirmation sound is heard, send another

transmission by pressing and releasing the tamper switch of the device.

4. As soon as 'Save?' appears press '√'.

Deleting a DT Detector from the System

To delete a DT detector from the system:

1. Set the system to Delete mode.

a. Go to the main menu and select [9]>[1]>[1]

(Programming > Devices > Zones).

b. Select a zone and press '√'.

2. Press >12>√.

3. Open the detector and take out the battery.

4. Close and hold the tamper switch.

5. Insert the battery (while the tamper is being pressed).

6. Wait for the the LEDs to stop blinking. Within 5 seconds, open the tamper and close it again.

Step 5: Mount the Detector on the Wall Bracket

Figure 5

Unscrew and separate detector from mounting bracket.

Figure 6

Open the 5 knockout holes of the wall bracket, and use as a template for mounting.

Figure 7

Secure the wall bracket to the wall using the 5 screws.

Figure 8

CAUTION! Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries according to local regulations.

CAUTION! The detector batteries are supplied inside of the unit, which are covered

with plastic wrapping. Remove the plastic wrapping from the batteries before

installation.

Observing battery polarity, insert 3 CR123 3V Lithium batteries (supplied) into the

batteries compartment.

Figure 9

Insert and fasten the screw to lock the detector.

Performing a Walk Test

Figure 10

The detector automatically enters walk test mode for 10 minutes following tamper

closure. Walk through the entire protected area and observe the LEDs to confirm full

coverage (see LED Status).

Manually initiate a walk test:

From the main menu: 7)Service > 3)Tests > 4)Walk test

(Quick key 7>03>4)

After completing the walk test, set the system to normal operation mode.

MW Range Adjustment

1Over power

2Under power

3Correct adjustment

ADetector

BCorridor

Anti-Mask Calibration

Following tamper closure, the anti-mask calibration procedure begins (up to 2 minutes). For

successful calibration, make sure that there are no objects near the detector for the duration of the

procedure.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Risco Capteur de sécurité

Risco

Risco RK6F Manuel utilisateur

Risco

Risco iWave RWX95 Manuel utilisateur

Risco

Risco WL X312 Manuel utilisateur

Risco

Risco Wirless WatchOUT RWX312PR800C Manuel utilisateur

Risco

Risco Bware BUS DT G2 Manuel utilisateur

Risco

Risco Beyond Wireless DT Manuel utilisateur

Risco

Risco BWare RK515DTG3 Manuel utilisateur

Risco

Risco iWave DT Pet Series Manuel utilisateur

Risco

Risco Digi-415DT Manuel utilisateur

Risco

Risco LuNAR PR RK2000DPC Manuel utilisateur

Risco

Risco iWISE Wireless RWT92 Manuel utilisateur

Risco

Risco WatchOUT Manuel utilisateur

Risco

Risco RK66S Manuel utilisateur

Risco

Risco Digital ZoDIAC RK410PRD Manuel utilisateur

Risco

Risco ShockTec 601SM Manuel utilisateur

Risco

Risco WatchOUT XTreme 315DT Manuel utilisateur

Risco

Risco WL T6S Manuel utilisateur

Risco

Risco eyeWAVE RWX95CMP Manuel utilisateur

Risco

Risco WatchU Manuel utilisateur

Risco

Risco iWISE RWT92043300C Manuel utilisateur

Risco

Risco iWave RWX95 Manuel utilisateur

Risco

Risco LuNAR PR RK2000DPC Manuel utilisateur

Risco

Risco WatchIN RK325DT Manuel utilisateur

Risco

Risco RK350DT Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur