RIOTEC FS5020E Manuel utilisateur

Laser Barcode

Scanner

User’s Manual

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user‘s authority to operate the equipment.

Limited Warranty

No warranty of any kind is made in regard to this material, including, but not limited to,

implied warranties of merchantability or fitness for any particular purpose. We are not liable

for any errors contained herein or for incidental or consequential damages in connection with

furnishing, performance or use of this material. We shall be under no liability in respect of

any defect arising from fair wear and tear, willful damage, negligence, abnormal working

conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of

the products without written approval.

Table of Contents

1. INTRODUCTION………………………………………………………………………………..….2~3

2. INSTALLATION………………………………………………………………………………..….......4

3. SET UP FROM BAR CODE LABEL………………………………………………………….……..7

Multi-interface Functions……….………………………………………………………..8~9

Interface-KBW………………………………………………………………………………….10

Interface-Serial……..……………………………………………………………………11~12

Symbologies On/Off…………………………………………………………………….13~15

Symbologies Set Up…………………………………………………………………….16~21

Edit Setup Bar Codes……………………………………….……………….………..…… 22

Macro/Special Keys Setup Bar Codes………………………………………………….23

Termination String Setup Bar Codes…………………………………………………..24

4. APPENDIX A: TROUBLESHOOTING AND ERROR BEEPS……..………………….25~29

Introduction

Our 1D Laser barcode scanner combines the best scanning performance and value. The device

provides an accurate, easy, and fast method of data entry and data storage for computerized

information systems. It is easy to install and does not require Software or drivers to operate.

Our laser barcode scanner can compatible several interfaces (USB, K/B, RS-232,) and

numerous configurations, is a powerful and reliable handheld scanner without compromise.

All the operating parameters are programmed by bar code programming menu and stored in

non-volatile RAM which can retain the settings after power is turned off.

When a barcode is successful decoded, the blue LED light of the scanner will turn on and off.

The scanner will beep once. If the barcode is not successful read, the LED will show red and

the buzzer will not sound.

Exit Window

Trigger

Exit window

Buzzer

LED

reen/red

)

Exit Window

Trigger

Buzzer

Handle

Installation

Insert the plug on the free end of the Communications Cable into the appropriate connector on

the host as below described:

1. USB cable Connection:

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the incorrect codes,

please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner

to its factory defaults settings in USB interface.

2. PS2 (K/B) cable Connection:

Connect with PC

Connect with

keyboard’s connector

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the incorrect codes,

please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to

its factory defaults settings in PS/2 interface.

3. RS232 cable Connection:

NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power

adapter to RS232 cable.

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the incorrect codes,

please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to

its factory defaults settings. Then “000601” for RS232 serial setting.

Connect with PC

Require adapter for power supply

4. Auto-sensing setup

For some scanners have auto-sensing function. There is an auto-sensing function button

shown on below photo. Default is ON.

*Auto-sensing normally is ON. Press once is OFF, Press once again is ON.

Operation

1. Be sure that Host computer is turned OFF.

2. Ensure that all connections are secure.

3. Turn on your host. And please operate the scanner under the right software

application, such as Notepad or Word(RS232 interface should be under

Hyper Terminal” and make the right setting).

4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default),

and press the trigger.

5. On successful decode, the blue LED light will turn on and off. The scanner will

beep once.

Tip

Do not hold the scanner directly over a barcode at 90˚. Scanning light bounces directly

back into the scanner from the barcode label is known as specular reflection which will

create a "dead zone" where decoding is difficult. Practice a few times to find what range

of angles works best.

Auto-sensing

button

Maintenance

Cleaning the scan window is the only maintenance required. A dirty window may

affect scanning accuracy.

Wipe the scanner window gently with a lens tissue or other material suitable for cleaning

optical material.

Do not spray water or other cleaning liquids directly onto the window.

Setup from Bar Code Label

Multi-Interface Functions – 1

OUTPUT FIRMWARE VERSION

RESET CONFIGURATION TO

DEFAULTS

OUTPUT MODE – KEYBOARD / USB OUTPUT

MODE

OUTPUT MODE - SERIAL

GOOD READ BEEP TONE – NONE BUZZER /

LED

GOOD READ BEEP TONE - RESET

DECODE OPTIONS REVERSE IMAGE –

ENABLE

IMAGE

DECODE OPTIONS REVERSE IMANGE

- DISABLE

DECODE OPTIONS SEND BAR CODE ID -

DISABLE

CODE ID

DECODE OPTIONS SEND BAR CODE

ID – AS A PREFIX

DECODE OPTIONS SEND BAR CODE ID -

RESET

DECODE OPTIONS SEND BAR CODE

ID – AS A SUFFIX

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iDC9503A Manuel utilisateur

RIOTEC

RIOTEC DC9250 Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iDC9608KW Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC iDC9502K Manuel utilisateur

RIOTEC

RIOTEC iDC9607LW Manuel utilisateur

RIOTEC

RIOTEC CR6327A Manuel utilisateur

RIOTEC

RIOTEC iDC9607A Manuel utilisateur

RIOTEC

RIOTEC iDC9600C Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC FS5108J Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC LS6307L Manuel utilisateur

RIOTEC

RIOTEC LS6300V Manuel utilisateur

RIOTEC

RIOTEC FS5102N Manuel utilisateur

RIOTEC

RIOTEC iDC9607A Manuel utilisateur

RIOTEC

RIOTEC iDC9272N Manuel utilisateur

RIOTEC

RIOTEC iLS6300JBU Manuel utilisateur

RIOTEC

RIOTEC iDC9508K Manuel utilisateur

RIOTEC

RIOTEC iLS6302ABQ Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur