RIOTEC ILS6302J/KBU Manuel utilisateur

Programming Quick Guide

-iLS6302J/KBU/iLS6302J/KB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3). If you are unable to complete this setting

within 1 minute, please re-plug USB cable & re-start the scanner,

and try again.

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6302J/KB

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Offline / out of service

Green LED ON Good read

Remark:

*When the battery power is too low, the Orange LED will flash

and beep once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully

before turning it back on.

*Under power-saving mode, there will not be LED indication when

charging.

Reset Configuration to Defaults

(scan from A1 to A2 for iLS6302J/KBU or B1 to B3 for iLS6302J/KB)

iLS6302J/KBU iLS6302J/KB

A1 B1

A2 B3

*Note: Please install PL-2303 driver for iLS6302J/KB

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

Transmission

1transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed Ultra Slow-speed

Transmission 3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner will

stop sending auto-connection signal to device

after 2 minutes. During this time, it will not enter

power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

1

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard for

your country or language. As a general rule, the following characters are

not supported by the scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

Portugal

Switzerland Hungary

Power-saving Mode

Power-saving mode OFF

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode automatically.

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. scan above configuration code for Prefix or Suffix

2. enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. scan above configuration code for Prefix or Suffix

2. enter the “0” “0” (above, right)

3. then end by scanning Code X (below, right)

Numeric barcode for settings

1 7

2 8

3 9

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL Y

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 951 Q 69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ;53 S 6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D =55 U 6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS) 27 ' 3F ?57 W 6F o

09 Tab

(HT) 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 29 ) 41 A59 Y 71 q

0B CTRL K

(VT) 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 2B + 43 C5B [ 73 s

0D Enter

(CR) 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 2D - 45 E5D ] 75 u

0F CTRL O

(SI) 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 2F / 47 G5F _ 77 w

11 CTRL Q

(DC1) 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 31 1 49 I61 a 79 y

13 CTRL S

(DC3) 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 33 3 4B K63 c 7B {

15 CTRL U

(NAK) 34 4 4C L 64 d 7C |

16 CTRL V

(SYN) 35 5 4D M65 e 7D }

17 CTRL W

(ETB) 36 6 4E N 66 f 7E ~

18 CTRL X

(CAN) 37 7 4F O67 g

2

Redundancy Level

This scanner offers two levels of decode redundancy. Select higher

redundancy levels for decreasing levels of bar code quality.

As redundancy levels increase, the decoder’s aggressiveness decreases.

Select the redundancy level appropriate for the bar code quality.

Redundancy Level 1

barcode must be successfully read twice

before being decoded

Redundancy Level 2

barcode must be successfully read three times

before being decoded

1D Symbologies On/OFF -1

ENABLE

UPC-A DISABLE

ENABLE

UPC-E DISABLE

ENABLE

EAN-8 DISABLE

ENABLE

EAN-13 DISABLE

ENABLE

MSI DISABLE

1D Symbologies On/OFF -2

ENABLE

Code 128 DISABLE

ENABLE

Code 32 DISABLE

ENABLE

CODE 93 DISABLE

ENABLE

CODE 11 DISABLE

ENABLE

Interleaved 25 DISABLE

ENABLE

Discrete 25 DISABLE

ENABLE

Code 39 DISABLE

ENABLE Code 39

FULL ASCII DISABLE

ENABLE Trioptic

Code 39 DISABLE

1D Symbologies On/OFF -3

ENABLE

GS1 DataBar DISABLE

ENABLE GS1 DataBar

Limited DISABLE

ENABLE GS1 DataBar

Expanded DISABLE

ENABLE Composite

CC-C DISABLE

ENABLE Composite

CC-A/B DISABLE

ENABLE Composite

TLC 39 DISABLE

ENABLE

Matrix 25 DISABLE

ENABLE

Chinese 25 DISABLE

ENABLE

CODABAR DISABLE

3

2D Symbologies On/OFF

ENABLE

PDF 417 DISABLE

ENABLE Micro

PDF 417 DISABLE

ENABLE

Data Matrix DISABLE

ENABLE

Maxicode DISABLE

ENABLE

QR CODE DISABLE

ENABLE Micro

QR CODE DISABLE

ENABLE

Aztec DISABLE

ENABLE

ISBT 128 DISABLE

Quick guide is subject to change without notice. R_140902_05

4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iDC9602A Manuel utilisateur

RIOTEC

RIOTEC DC9273A Manuel utilisateur

RIOTEC

RIOTEC iDC9607AW Manuel utilisateur

RIOTEC

RIOTEC LS6000B series Manuel utilisateur

RIOTEC

RIOTEC iLS6302KS Manuel utilisateur

RIOTEC

RIOTEC iLS6300VBU Manuel utilisateur

RIOTEC

RIOTEC iDC9272N Manuel utilisateur

RIOTEC

RIOTEC OM7220L Manuel utilisateur

RIOTEC

RIOTEC iLS6300JBQ Manuel utilisateur

RIOTEC

RIOTEC iCR6307AB Manuel utilisateur

RIOTEC

RIOTEC iDC9270J Manuel utilisateur

RIOTEC

RIOTEC FS5027L Manuel utilisateur

RIOTEC

RIOTEC iDC9608K Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBU Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6303XS Manuel utilisateur

RIOTEC

RIOTEC iDC92700 Manuel utilisateur

RIOTEC

RIOTEC iCR6300CBQ Manuel utilisateur

RIOTEC

RIOTEC DC9257L Manuel utilisateur

RIOTEC

RIOTEC LS6307L Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

RIOTEC

RIOTEC iLS6302ABU Manuel utilisateur

RIOTEC

RIOTEC LS6320E Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

RIOTEC iLS6302J/KBU Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques