Riello 370T1 Series Guide de démarrage rapide

2903193 (5) - 12/2006

Installation, use and maintenance instructions

Montage und Bedienungsanleitung

Light oil burners

Öl-Gebläsebrenner

CODE MODEL

MODELL

TYPE

TYP

3737005 BGK1 370T1

3737405 BGK2 374T1

One stage operation

Einstufiger Betrieb

DECLARATION OF CONFORMITY Royal Decree (A.R.) 8/1/2004 -

Belgium

Producer: RIELLO S.p.A.

Via Pilade Riello, 7

37045 LEGNAGO (VR) Italy

Tel. ++39.0442630111

Fax ++39.044221980

Distributed by: RIELLO NV

Ninovesteenweg 198

9320 Erembodegem

Tel. (053) 769 030

Fax. (053) 789 440

e-mail. info@riello.be

URL. www.riello.be

This is to certify that the series of units specified below conforms to the model of the type

described in the EC declaration of conformity, and is produced and distributed in conformity with

the requirements laid down in Belgian Royal Decree (A.R.) dated 8 January 2004.

Product type: Light oil burner

Model: BGK1 – 370T1

BGK2 – 374T1

Standard applied: EN 267 and A.R. of 8 January 2004

Control body: TÜV Industrie Service GmbH

TÜV SÜD Gruppe

Ridlerstrase, 65

80339 Munchen DEUTSCHLAND

Measured value: NOx max: 120 mg/kWh

CO max: 8 mg/kWh

Date: 30/11/2005 RIELLO S.p.A.

3193 1GB

INDEX

1. BURNER DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.1 Burner equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Overall dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.3 Firing rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3. INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1 Working position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.2 Boiler fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.3 Hydraulic systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.4 Electrical wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. BURNER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.1 Combustion adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.2 Recommended nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.3 Pump pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.4 Maintenance position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.5 Combustion head setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.6 Air damper setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.7 Electrode positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.8 Flame detector adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.9 Fuel heating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.10 Operating programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6. FAULTS / SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

7. SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.1 Burner identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.2 Basic safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3193 2GB

1. BURNER DESCRIPTION

One stage light oil burner with low pollutant emissions (Nitric Oxide NOx, Carbon monoxide CO and unburnt

Hydrocarbons).

1.1 BURNER EQUIPMENT

Flange with insulating gasket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. 1

Screw and nuts for flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

7 pin plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. 1

Recirculating pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Screw and nuts for flange to be fixed to boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 4

Flexible oil pipes with nipples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. 2

1–Oilpump

2– Air damper adjustment assembly

3– Nozzle holder assembly

4– Flange with insulating gasket

5– Control box

6– Reset button with lock-out lamp

7– Flame detector

8– Combustion head

9– Recirculation pipe

10 –Motor

³Burner with CE marking in conformity with EEC directives: EMC 89/336/EEC, Low Voltage 73/23/EEC,

Machines 98/37/EEC and Efficiency 92/42/EEC.

³CE Certification No.: 0036 0232/98 (370T1) – 0036 0233/98 (374T1), as 92/42/CEE.

³The burner meets protection level of IP X0D (IP 40) as EN 60529.

³The burner is approved for intermittent operation as per Directive EN 267.

D7290

Fig. 1 2

3193 3GB

2. TECHNICAL DATA

2.1 TECHNICAL DATA

2.2 OVERALL DIMENSIONS

2.3 FIRING RATES, (as EN 267)

TYPE 370T1 374T1

Output 1.5 −3.0 kg/h 2.7 −5.0 kg/h

Thermal power 17.8 −35.6 kW 32 −59.3 kW

Fuel Light oil, viscosity 4 – 6 mm2/s at 20 °C

Electrical supply Single phase, 230V ±10% ~50Hz

Motor Run current 0.8A – 2750 rpm – 288 rad/s

Capacitor 4 µF

Ignition transformer Secondary 8 kV – 16 mA

Pump Pressure 8 – 15 bar

Absorbed electrical power 0.25 kW

TYPEABCDEØ FØ GHIL

370T1 255 280 202 230 192 87 89 10 28 107

374T1 255 280 202 230 197 90 89 10 28 115

45°

Ø G

189

106

140

168

Ø F

D7217

Pressure in combustion

chamber – mbar

Light oil output – kg/h

Thermal power – kW

15 20 25 30

35 40 45 50 55

D7637

0,2

0,8

0,6

0,4

370T1 374T1

3193 4GB

3. INSTALLATION

THE BURNER MUST BE INSTALLED IN CONFORMITY WITH LEGISLATION AND LOCAL STANDARDS.

3.1 WORKING POSITION

The burner is designed for operation in positions 1and 2only. Installation 1is the preferred option as it is the

only one that enables maintenance to be performed as described later on in this manual.

Operation is possible with installation option 2though maintenance cannot be performed with the burner con-

nected to the boiler. Note that any other installation position is likely to hinder the unit’s proper operation. Instal-

lations 3, 4 and 5are prohibited as safety is compromised.

3.2 BOILER FIXING

Important: with some boilers it is possible that the CO values exceed those declared in this manual.

To reduce these emissions, the recirculation pipe supplied must be used.

To fit the burner to the boiler it is necessary to carry out the following:

³If necessary insert the recirculating pipe (1) on the burner blast tube (2) and fix it with the screw (3), (see

fig. 2).

Attention: respect the dimensions, as described in chapter “2.2 OVERALL DIMENSIONS“ at page 3.

³Put on the flange (4) the screw and two nuts, (see fig. 4).

³Widen, if necessary, the insulating gasket holes (5, fig. 5).

³Fix the flange (4) to the boiler door (6) using screws (7) and (if necessary) the nuts (8) interposing the

insulating gasket (5), (see fig. 3).

D7088

1 2 3 4 5

S7709

Boiler door must have a max. thickness of 80 mm, refractory linig included.

ATTENTION

S7708

E9163

D5012

Fig. 2 3

1 2

Fig. 4

Fig. 5

Fig. 3

3193 5GB

3.3 HYDRAULIC SYSTEMS

*ONLY FOR ITALY: Automatic shut-off device as per Ministry of Internal Affairs’ regulation no. 73 dated 7/29/71.

H= difference of level; L= max. length of the suction line; I. D. = internal diameter.

PRIMING PUMP:

On the system in fig. 6 it is sufficient to loosen the suction gauge connec-

tion (6, fig. 7) and wait until oil flows out.

On the systems in fig. 8 and 9 start the burner and wait for the priming.

Should lock-out occur prior to the arrival of the fuel, await at least 20 sec-

onds before repeating the operation.

The pump suction should not exceed a maximum of 0.4 bar (30 cm Hg).

Beyond this limit gas is released from the oil. Oil pipes must be completely

tight.

In the vacuum systems (fig. 9) the return line should terminate within the oil

tank at the same level as the suction line. In this case a non-return valve is

not required. Should however the return line arrive over the fuel level, a

non-return valve is required. This solution however is less safe than previ-

ous one, due to the possibility of leakage of the valve.

meters

L meters

øi

8 mm

øi

10 mm

0,5

1,5

100

The burner is designed to accommodate the installation of

light oil supply pipes on either side.

It is necessary to install a filter on the fuel supply line.

The pump is designed to allow working with two pipes. In

order to obtain one pipe working it is necessary to unscrew

the return plug (2), remove the by-pass screw (3) and then

screw again the plug (2). (See fig. 7).

Before starting the burner make sure that the return pipe-

line is not clogged. An excessive back pressure would

cause the damage of the pump seal.

WARNING:

meters

L meters

øi

8 mm

øi

10 mm

0,5

1,5

3,5

100

SYSTEM

NOT PERMITTED 1- Suction line

2- Return line

3- By-pass screw

4 - Gauge connection

5- Pressure adjuster

6- Suction gauge connection

7- Valve

8- Auxiliary pressure gauge

324

Fig. 7

D5487

max. 4 m

D6329

Fig. 8 Fig. 9

max. 4 m

D6328

Fig. 6

IN GERMANY

3193 6GB

3.4 ELECTRICAL WIRING

CARRIED-OUT IN THE FACTORY

7 pin plug

7 pole socket

L1 B4S3T2T1N

Black

White

Blue

Capacitor

Burner-earth

Main switch

T6A

Neutral

CONTROL BOX

550SMD

230V ~50Hz

1231231234

DO NOT EXCHANGE NEUTRAL WITH PHASE

WARNING

Motor

D5521 Heater with start

thermostat

Flame detector

Safety

thermostat T

Black

Blue

Oil valve

Hour counter

(230V - 0.1A max.)

Limit

thermostat Remote lock-out signal

(230V - 0.5A max.)

Ignition

electrodes

Brown

Blue

Brown

Black

S7145

NOTES:

– Wires of min. 1 mm2section. (Unless requested oth-

erwise by local standards and legislation).

– The electrical wiring carried out by the installer must

be in compliance with the rules in force in the Country.

*(See page 5). Connect the automatic shut-off de-

vice (230V - 0.5A max.) to the clamps N - T2 of the

7 pin plug.

CONTROL BOX

■To remove the control-box from the burner, loosen screw (A, fig. 10)

after removing all components, the 7 pin plug and earth wire.

During the re-assembly of the control box, retighten the screw

(A) with a torque wrench setting of 1 – 1.2 Nm.

■For burners installed on air generators, remove the bridge (B, fig. 10)

from the control box.

TESTING:

Check the shut-down of the

burner by opening the thermo-

stats and the lock-out by

darkening the flame detector.

Fig. 10

E9070

Green led (Fan)

Yellow led (Heater)

Red led (Lock-out signalling due to failure to shut-down)

3193 7GB

4. BURNER OPERATION

4.1 COMBUSTION ADJUSTMENT

In conformity with Efficiency Directive 92/42/EEC the application of the burner on the boiler, adjustment and

testing must be carried out observing the instruction manual of the boiler, including verification of the CO and

CO2concentration in the flue gases, their temperatures and the average temperature of the water in the boiler.

To suit the required appliance output, choose the proper nozzle and adjust the pump pressure, the setting of

the combustion head, and the air damper opening in accordance with the following schedule.

The values shown in the table are measured on a CEN boiler (as per EN 267), and they refer to 12.5% CO2

at sea level (1013 hPA) and with light oil and room temperature of 20 °C, with a combustion chamber pres-

sure of 0 mbar.

4.2 RECOMMENDED NOZZLES

Steinen type 60° H;

Danfoss type 60° H;

Delavan type 60° W.

4.3 PUMP PRESSURE

The pump leaves the factory set at 12 bar.

To change it act on pump pressure adjust screw (5, fig. 7, page 5).

TYPE

Nozzle Pump

pressure

Burner

output

Combustion head

adjustment

Air damper

adjustment

GPH Angle bar kg/h ± 4% Set-point Set-point

370T1

0.40 60° W 13 1.5 11.4

0.50 60° W 12 1.7 1.5 1

0.60 60° W 12 2.1 22.2

0.65 60° W 12 2.3 2.5 2

0.75 60° W 12 2.7 3 3

0.75 60° W 14 3.0 3.5 3.2

374T1

0.75 60° W 12 2.7 1.5 1.2

0.85 60° W 12 3.0 1.5 1.8

1.00 60° W 12 3.7 2 2

1.10 60° W 12 4.1 2.5 2.2

1.25 60° W 12 4.6 3.5 2.8

1.25 60° W 14 5.0 4 3

QUALIFIED PERSONNEL WITH THE RIGHT INSTRUMENTS MUST HANDLE THE BURNER'S FIRST

START-UP

WARNING

NOTE:

to achieve CLASS 3 (EN267:1999) emissions, hollow-cone

nozzles have been used.

3193 8GB

4.4 MAINTENANCE POSITION, (fig. 11)

Before performing maintenance on the burner, it is

best to disconnect the system’s power supply.

³Unscrew and remove the screw fastening it to the

flange to take the burner off the boiler.

³Hook the burner onto flange (7), loosen screws (5)

and pull off the blast tube assembly (4).

³Loosen screw (3, fig. 14 page 9) to remove the dif-

fuser disc support assembly (3) from nozzle-holder

assembly (1).

³Pull wires (2) out from electrodes.

³Replace nozzle (6) and screw the new one on prop-

erly, holding it as illustrated in figure 11.

³Refit following the above procedure in the reverse

order.

4.5 COMBUSTION HEAD SETTING, (fig. 13)

Combustion head adjustment varies depending on

burner delivery. To adjust, proceed as follows:

³Turn adjusting screw (2) clockwise or anticlockwise

until the notch on the regulating rod (3) is lined up with

the outer surface of the nozzle-holder assembly (1).

³In the example, the regulating rod (3) is set to setpoint

3. This means the burner is adjusted for an output of

2.7 kg/h with a pump pressure of 12 bar using a 0.75

GPH nozzle, as indicated in the reference table relat-

ing to burner type 370T1.

4.6 AIR DAMPER ADJUSTMENT

To adjust the air damper proceed as follows:

³Loosen nut (5, fig. 13) and set the valve by adjusting

the screw (4).

³When the adjustment is complete screw down nut (5).

Type 370T1 - BGK1

When the burner stops, the air damper closes automati-

cally until maximum negative flue pressure is 0.5 mbar.

Type 374T1 - BGK2

When the burner stops, the air damper stays open.

6 7

E9286

Fig. 11

D7291

Fig. 13 2

4 5

WARNING

In the event of maintenance

made to the diffuser disc-hold-

er assembly, screw the nut (A)

as shown in the figure 12.

TIGHTEN WITHOUT MOVING

BACKWARDS TO THE END

D5684

Fig. 12

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Riello Brûleur

Riello

Riello PRESS 45 N 615 M Guide de démarrage rapide

Riello

Riello Gulliver BG7D Guide de démarrage rapide

Riello

Riello DB 4 SM BLU Guide de démarrage rapide

Riello

Riello 974 T Guide de démarrage rapide

Riello

Riello RG0.1 Guide de démarrage rapide

Riello

Riello RL 250 Manuel utilisateur

Riello

Riello RG5D Guide de démarrage rapide

Riello

Riello PRESS GV Series Manuel utilisateur

Riello

Riello DB 4 LSM C13 Guide de démarrage rapide

Riello

Riello RS 45/E BLU Guide de démarrage rapide

Riello

Riello BS2F-GPL Guide de démarrage rapide

Riello

Riello RN 28 Guide de démarrage rapide

Riello

Riello 20169021 Guide de démarrage rapide

Riello

Riello PRESS GV INCINERATOR Guide de démarrage rapide

Riello

Riello RS 300/EV FGR Guide de démarrage rapide

Riello

Riello 606T1 Guide de démarrage rapide

Riello

Riello FS10 Guide de démarrage rapide

Riello

Riello RS 310/E BLU Guide de démarrage rapide

Riello

Riello 1301 T Guide de démarrage rapide

Riello

Riello RDB3.2 VORT 58 Guide de démarrage rapide

Riello

Riello 46662X Guide de démarrage rapide

Riello

Riello RS 50/M MZ Instructions d'utilisation

Riello

Riello 467 T80 Guide de démarrage rapide

Riello

Riello Gulliver BS1 Guide de démarrage rapide

Manuels Brûleur populaires d'autres marques

True Induction

True Induction TI4B Manuel utilisateur

Weishaupt

Weishaupt WG20 Series Manuel utilisateur

Carolina Cooker

Carolina Cooker M116672 Manuel utilisateur

Unigas

Unigas HTP2000 Manuel utilisateur

baltur

baltur BT 250 DSG 4T Manuel utilisateur

muenkel design

muenkel design round burner Manuel utilisateur

Ecoflam

Ecoflam Multicalor 170.1 Manuel utilisateur

baltur

baltur BT 14 DSGW Manuel utilisateur

artisan

artisan Art-SB1 Mode d’emploi

AESYS

AESYS TurboFire II Manuel utilisateur

IKEA

IKEA GRILLSKÄR Manuel utilisateur

RUSTA

RUSTA SAREK Manuel utilisateur

PROPOINT

PROPOINT 8933657 Manuel utilisateur

baltur

baltur TBL 1000 ME Manuel de référence

Riello Burners

Riello Burners P 200 P/G Guide de démarrage rapide

WLD-TEC

WLD-TEC powerjet Manuel utilisateur

MSR

MSR DRAGONFLY Manuel utilisateur

baltur

baltur COMIST 23SP Manuel utilisateur