Ricoh Rh 100 Manuel utilisateur
DSA121
DYX362
Mode indicator
*1
• Light: Press the [Preheat] key to start preheating
• Flashing: Preheating under way
• Off: Preheating completed
Tray
Printer
(Ri 100)
Finisher
(This machine Rh 100)
Front Cover
Mode Switching
Lever
Time/temperature indicator [Temperature] key [Preheat] key*1 [Power] key
[Time] key [Stop/Unlock] key
Control Panel
Guide to Components of the Finisher
This guide describes the basic printing procedures using the
printer and this machine. In the next pages, the procedures
for each step and particular cautions are explained.
For safe and correct use, be sure to read Safety Information
before using the machine.
Quick Guide
Basic Usage of the Finisher
CAUTION:
A parent or guardian must be present if infants, children, or people who need assistance use the ma-•
chine, and they should be very careful when using it. Otherwise, injury or burns may result.
The finisher has “Standard mode”, “Professional mode”, and “Professional 2 mode”.
Standard mode
◆
The factory-default setting is standard mode. The finisher has the following functions
to prevent children from touching the inside of the finisher accidentally when it is very
hot.
When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To•
open the front cover, press the [Stop/ Unlock] key for at least 1 second.
The surface of the heater and the fabric are not in contact with each other during the
fixing process, so the surface of the heater does not become dirty.
Professional mode
◆
To use this mode, switch from standard mode.
As this mode is for users who are accustomed to using the finisher, the front cover
does not lock even when the temperature of the inside of the finisher exceeds 70 °C
(158 °F).
However, during press processing and fixing processing, the front cover locks regard-
less of whatever mode is used to prevent erroneous operations.
The surface of the heater and the fabric are not in contact with each other during the
fixing process, so the surface of the heater does not become dirty.
Professional 2 mode
◆
This mode minimizes the loss of color when T-shirts are washed.
To use this mode, switch from professional mode.
As this mode is for users who are accustomed to using the finisher, the front cover
does not lock even when the temperature of the inside of the finisher exceeds 70 °C
(158 °F).
However, during press processing and fixing processing, the front cover locks regard-
less of whatever mode is used to prevent erroneous operations.
The surface of the heater and the fabric are in contact with each other during the fixing
process, so regular cleaning of the surface of the heater is necessary.
* Refer to Operating Instructions for cleaning frequency and precautions.
How to Switch Modes
◆
Press the [Temperature] key and
[Time] key simultaneously for at least
2 seconds.
DYX353
The operating mode changes as fol-
lows.
Standard mode
Professional
2 mode
Professional
mode
DYX354
Unlock Cover
◆
When set to standard mode, press
the [Stop/ Unlock] key for at least 1
second.
DYX360
When set to the professional mode,
it is not necessary to hold down the
[Stop/Unlock] key.
Operating Procedure
Perform the procedures in the order of 1, 2, 3, and then 4.
The following settings and procedures are examples for major fabrics.
Depending on your environment, discoloration may occur or the ink may not be fixed prop-
erly. Before configure the settings, check the fixability of the fabric you use.
Fabric type Mode Temperature 1. Preparation 2. Pressing 3. Printing 4. Fixing
T-shirt Standard mode
Professional
mode
170°C (338°F) See next
page.
30sec See Ri 100
Operating
Instructions.
3min
Professional 2
mode
180°C (356°F) 30sec 30sec
3min
Tote bag (thick) Standard mode
Professional
mode
170°C (338°F) 30sec 3min
Tote bag (thin) 150°C (302°F) 30sec 3min
Sweatshirts 170°C (338°F) 30sec 3min
© 2017, 2018 Ricoh Co., Ltd.
EN GB EN US EN AU J361-6607E
Preparation
Loading the fabric in the tray
For details, refer to User’s Guide provided with the printer Ri 100.
You can shorten the processing time by putting a garment in the tray while preheating the
finisher.
➊
Press the [Power] key to turn on the power..
➍
Set the amount of time that the heater is on.
Set the time according to the fabric on which you
are printing. The default setting is “Medium”.
➋
Make sure the mode switching lever is set in the
center.
➎
When the [Preheat] key is lit, press the [Preheat]
key to start preheating.
When the [Preheat] key is unlit, no operation is
necessary because preheating is completed.
➌
Set the temperature of the heater.
Set the temperature according to the fabric on which
you are printing. The default setting is “High”
Procedure for ( )
➊
When you move the mode switching lever to the
left, processing starts. An alarm sounds after pre-
heating is completed.
➋
Procedure for ( )
➊
When you move the mode switching lever to the
right, processing starts. An alarm sounds after
preheating is completed.
➋
Autres manuels pour Rh 100
1
Table des matières
Autres manuels Ricoh Imprimante
Ricoh
Ricoh Aficio 2238C Manuel utilisateur
Ricoh
Ricoh InfoPrint 1767 Manuel utilisateur
Ricoh
Ricoh Aficio SP C430DN Manuel utilisateur
Ricoh
Ricoh G190 Manuel utilisateur
Ricoh
Ricoh Martini-C3 Manuel de service
Ricoh
Ricoh Aficio SP C811DN Series Manuel utilisateur
Ricoh
Ricoh AP610N - Aficio B/W Laser Printer Manuel utilisateur
Ricoh
Ricoh Pro C9200 Manuel utilisateur
Ricoh
Ricoh Aficio MP 2550B Manuel utilisateur
Ricoh
Ricoh Pro L5160 Manuel d'entretien
Ricoh
Ricoh InfoPrint EMP156 Manuel utilisateur
Ricoh
Ricoh Priport DX 4640PD Instructions d'installation et d'entretien
Ricoh
Ricoh M C250FW Manuel utilisateur
Ricoh
Ricoh SP 201n Manuel utilisateur
Ricoh
Ricoh MP 6503 Series Manuel utilisateur
Ricoh
Ricoh Pro 907 Mode d'emploi
Ricoh
Ricoh SP C435DN Manuel utilisateur
Ricoh
Ricoh SP 112SU Manuel utilisateur
Ricoh
Ricoh CL3500N - Aficio Color Laser Printer Manuel utilisateur
Ricoh
Ricoh C210SF - Aficio SP Color Laser Instructions d'installation
