Ricoh PRIPORT VT1730 Manuel utilisateur
PRIPORT VT1730
Operating Instructions
-Machine Exterior MAJOR COMPONENTS
MAJOR COMPONENTS
Machine Exterior
TOP COVER ADF UNIT
Open this cover to The Automatic Document
access the inside of Feeder (ADF) feeds the
the machine.
\
original to the printing
positiyn automati=lly.
AI-=x\ \
this
15.
/
TAPE DISPENSER
(option)
This feeds out strips
of paper which
separate the printing
groups on the paper
delive~ table.
PAPER DELIVERY OPERATION PANEL
TABLE Operator controls
Completed prints and indicators are
are delivered here. located here. See
See page 17. page 2.
MAJOR COMPONENTS Operation Panel
Operation Panel
=Keys -
IMAGE MODE KEY SPEED KEY
Press to select the Line Press to adjust the rotation
mode or Photo mode in speed of the machine in
aocordanoe with the type accordance with the type of
and quality of the original.
See page 35. \image and printing paper.
See page 27 and 28.
c--
El
0(
1
0(
4
0(
7
+
/ \
/
IMAGE DENSITY
KEY
Press to make
prints darker or
lighter. See page 27.
/\IMAGE POSITION
AUTO CYCLE KEY RESET KEY KEY
Use to automatically Press to reset Press to shift the
process masters and error indicators. image forwards or
make prints. See backwards on the
page 30. print paper. See
page 24.
Operation Panel MAJOR COMPONENTS
MEMORY/CLASS KEY
Press to select group
printing. See page 31
and 33. \
\
NUMBER KEYS
Press to enter the
numb~r of prints.
STOP KEY
Press to stop the machine. The
machine will continue printing when
the Print Startkey is pressed. If you
stop making amaster, the “~+ A“
indicators will blink and the machine
will not continue making the master
when the Master Making key is
\I
m
MASTER
~MAKING KEY
Press to make a
master.
/
CLEAR KEY \PRINT START KEY
Press to change Press to start printing.
ENTER KEY the number that PROOF KEY
Press to input is set in the Press to make trial
munter.
information into prints or extra prints.
the memory.
INSTALLATION REQUIREMENTS Machine Environment Environments To Avoid
INSTALLATION REQUIREMENTS
Machine Environment
The installation location should be carefully chosen because environmental conditions greatly
affect the performance of the machine.
Optimum environmental conditions
ClTemperature: 10-30 ‘C, 50 -86‘F
ClHumidity: 20-90 %RH
IJ On astrong and level base (for example, asturdy desk).
ClThe machine must be level within 5mm, 1/5” both front to rear and left to right.
Environments To Avoid
DLocations exposed to direct sunlight or strong light (more than 1,500 Iux).
DLocations directly exposed to cool air from an air conditioner or to heat from aheater.
(Sudden temperature changes from low to high or vice versa may cause condensation
within the machine.)
~Dusty areas.
ClAreas with corrosive gases.
Power Connation Access To The Machine INSTALLATION REQUIREMENTS
Power Connection
0Securely connect the power cord to adedimted 120V,60HZ power source which
supplies more than 2.4A.
IJ Make sure the plug is firmly inserted into the outlet.
~Avoid multiwiring.
ClDo not pinch the power cord.
DMake sure that the wall outlet is near the machine and easily accessible.
~Voltage must not fluctuate more than 10 ?40.
Access To The Machine
Place the machine near apower source, providing clearan= as shown below.
Paper
Delivery Table
>
More than ‘More than
60 cm, 23.7” 60 cm, 23.7”
—&A
More than I
70 CM, 27.6”
5
.
SUPPLYING THE MASTER ROLL, INK, AND TAPE SupplyingThe Master Roll
.
SUPPLYING THE MASTER ROLL, INK,
AND TAPE
Supplying The Master Roll
Caution:
Caution:
When you open the top cover, make sure that there are no originals on the top
cover.
If you drop something, such as a clip, inside the machine, remove it before
continuing. If you cannot find what yOLJhave dropped or if you are unable to
remove it from the machine, contact your service representative.
1. Insert both spools into anew master
roll.
2. Open the top cover.
Caution: When you open or close the top
cover, be careful not to pinch your
fingers between the top cover and
the back cover.
Caution: When you open or close the top
cover, be careful not to hit yourhead
or hands against the switch actuator
of the top cover.
3. Position the new master roll as shown
in the illustration.
. .
6
4. Lift the pressure release Ieverin the
direction of the arrow to release the
feed roller pressure.
5. Insert the leading edge of the master
roll under the feed roller.
6. Return the pressure release lever to its
original position.
7. Turn on the main switch.
OThe main switch is located at the leftside
of the operation panel.
8. Press the master cut button to cut the
leading edge of the master roll.
Caution: When the master cut button is
pressed, the master roll will rotate.
Do not touch the master roll.
.,
SUPPLYING THE MASTER ROLL, INK, AND TAPE Supplying The Master Roll
9. Remove the cut-off portion of the
master roll.
~Removethecut-offmasterpaper
completelyto preventmastermisfeed.
CJ If the masterisslackafterrotating,move
the pressurereleaseleverseveraltimes
to take upthe slack.
10. Close the top cover,
Supplying Ink
1, Open the ink cover. r=
2. Press down the release lever (green
tab [A]). The ink pack holder slides out
part way.
3. Pull out the ink pack holder as shown.
Caution: Take your finger off the release lever
while puliing out the ink pack holder.
You may be injured by the edge of
the ho/der.
I
Remove the cap of the new ink pack.
ODonotremove the seal from the spoutof
the ink pack.
Table des matières
Autres manuels Ricoh Imprimante
Ricoh
Ricoh Ri 2000 Manuel utilisateur
Ricoh
Ricoh Aficio SP 4310N Guide de démarrage rapide
Ricoh
Ricoh Ri 2000 Manuel utilisateur
Ricoh
Ricoh Neptune-P1 Manuel utilisateur
Ricoh
Ricoh Aficio BP20N Manuel utilisateur
Ricoh
Ricoh LANIER AP2610 Manuel
Ricoh
Ricoh SP 230DNw Manuel utilisateur
Ricoh
Ricoh GXe3300N Manuel utilisateur
Ricoh
Ricoh SP 110 SU Manuel utilisateur
Ricoh
Ricoh PRO C9100 Manuel utilisateur
Ricoh
Ricoh Aficio MP 2550B Manuel utilisateur
Ricoh
Ricoh SP 213Nw Manuel utilisateur
Ricoh
Ricoh Aficio MP1812L Manuel utilisateur
Ricoh
Ricoh CI5040 Guide de démarrage rapide
Ricoh
Ricoh SP C420DN-KP - Aficio Color Laser Printer Manuel utilisateur
Ricoh
Ricoh Pro C9500 Guide de configuration
Ricoh
Ricoh Aficio SP C311N Manuel utilisateur
Ricoh
Ricoh L5160 Guide d'installation
Ricoh
Ricoh 3245 - Type Print Server Manuel de service
Ricoh
Ricoh 403080 - Aficio SP 4100N-KP B/W Laser... Manuel utilisateur
