Rice Lake OS-10 Manuel
RICE LAKE OS-10/OS-25/OS-45
On-Site Hanging Scale
Operators Guide
230 W. Coleman St. • Rice Lake, WI 54868 • USA
U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319
Rice Lake Weighing Systems is an ISO 9001 registered company.
© Rice Lake Weighing Systems Specifications subject to change without notice.
www.ricelake.com
PN 131079 Rev BJanuary 9, 2020
2 Visit our website www.RiceLake.com
Safety
Failure to heed
may result in minor or moderate injury.
DO NOT operate or work on scale unless you have read and
understand this manual.
Do not use for purposes other than weighing.
Do not leave loads unattended.
Do not Overload - it can damage the scale and will render the warranty null and void.
Cleaning
•Always turn scale off before cleaning.
•Alcohol based wipes when cleaning the scale are recommended.
•DO NOT spray with or submerse into water when cleaning.
•Refrain from using corrosive liquids or high pressure washers.
•Improper cleaning will render the warranty null and void.
Inserting/Replacing Battery
When LO appears on display, replace batteries with
two 1.5V AA batteries.
1. Remove the battery cover located on back of scale.
2. Remove batteries and dispose of properly.
3. Install new AA batteries according to the diagram in
the battery cavity.
4. Replace battery cover securely.
Error Messages
Limited Warranty
All systems and components are warranted against defects in materials and workmanship
for one year. For further information see www.ricelake.com.
Error Action Display
Low Battery Replace the batteries.
Over Load - Total load exceeds the
maximum capacity.
Remove weight from the
scale immediately.
Over Zero - Zero count is higher than the
setting range.
Scale turns off if status
continues 30 secs or longer.
Below Zero
Zero count is below the setting range.
Scale turns off if status
continues 30 secs or longer.
EEPROM error Call for service.
Table 1. Error Messages
CAUTION
IMPORTANT
Batteries
Battery Cover
Lo
Err
ErrL
ErrE
© Rice Lake Weighing Systems ● All Rights Reserved 3
Display and Button Functions
Figure 1. Hanging Scale
Operating Scale
Suspend the scale in a secure location.
Use scale in a vertical position only.
1. Press to power on.
2. Press to select units.
3. Suspend container from hook if one will be used.
4. Press to zero scale.
5. Place product on the scale, weight will appear in the display.
6. To turn the scale off, press and hold .
Key Item Description
1 Minus Signifies a negative weight.
2 Hold Signifies the weight is held.
3 Power/Zero Press to turn scale on.
Press to reset scale to zero.
Press and hold to turn scale off.
4 Units Select kilograms, pounds or pounds and ounces.
5 Hold Press to hold weight. Press again to release weight.
Table 2. Display and Button Function
o
POWER
ZERO
UNITS
Units
S
O
10
Minus
Hold
Capacity: 10.00kgx0.01kg/22lbx0.02lb/22lbx1/4oz
HOLD
5
2
4
3
1
Note
o
POWER
ZERO
UNITS
Units
o
POWER
ZERO
o
POWER
ZERO
4 Visit our website www.RiceLake.com
Hold Function
1. Press , when weight stabilizes display will lock and arrow will be steady.
2. Press to release locked weight.
Adjusting Auto-Off
1. Press to power on.
2. Press and hold . When AOFF displays, release.
3. Press to select auto-off time (OFF, 120, 180, 240, 300 seconds).
4. Press to return normal weighing mode.
Calibration
Calibrate using the following process:
1. Press and hold .
2. Press three times, ZERO COUNT displays.
3. Press , zero displays.
4. Press to select calibration unit.
5. Load appropriate amount of weight on scale (See Table 3). Display shows span count.
6. Press , CAL displays, then the weight.
7. Remove the weight, re-power the scale and calibration is complete.
Table 3. Calibration Weights
Model kg lb
OS10 10kg 20lb
OS25 20kg 40lb
OS45 20kg 40lb
HOLD
HOLD
o
POWER
ZERO
UNITS
Units
HOLD
UNITS
Units
o
POWER
ZERO
UNITS
Units
o
POWER
ZERO
UNITS
Units
o
POWER
ZERO
Certification
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference that may
cause undesired operation.
Autres manuels pour OS-10
2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Rice Lake Échelle
Rice Lake
Rice Lake CLS-M Manuel utilisateur
Rice Lake
Rice Lake Altralite Manuel utilisateur
Rice Lake
Rice Lake TE Series Manuel utilisateur
Rice Lake
Rice Lake DHH-10BT Manuel utilisateur
Rice Lake
Rice Lake MSI-6360 Manuel utilisateur
Rice Lake
Rice Lake BCD Manuel
Rice Lake
Rice Lake MS200 Manuel utilisateur
Rice Lake
Rice Lake Summit SB-1150 Manuel utilisateur
Rice Lake
Rice Lake D400 Manuel utilisateur
Rice Lake
Rice Lake OS-10 Manuel
Rice Lake
Rice Lake CW-90 Manuel utilisateur
Rice Lake
Rice Lake RL101 Manuel utilisateur
Rice Lake
Rice Lake OS-10 Manuel
Rice Lake
Rice Lake Survivor SR Manuel utilisateur
Rice Lake
Rice Lake DIGI DSX-1000 Manuel utilisateur
Rice Lake
Rice Lake RL1100EM Manuel utilisateur
Rice Lake
Rice Lake Summit 3000 Manuel utilisateur
Rice Lake
Rice Lake 350-10-3M Manuel utilisateur
Rice Lake
Rice Lake RoughDeck CC Caster Cargo Manuel utilisateur
Rice Lake
Rice Lake RoughDeck SS Manuel utilisateur
