Rexing S1 Pro Manuel utilisateur
1
S1 Pro
User Manual
2
Notice
1. Menu Setup Operation: The menu is to be set up in non-video mode.
If the device is in video mode, proceed after stopping the video
recording.
2. Memory card: A new card must be formatted to the machine before
use. Continuous image recording for long periods of time may
produce protected files that are not subject to long-term protection
(these files may not be overwritten during loop recording) and storage
fragments, which need to be cleared regularly in order to save stable
storage space.
3. Standard Voltage for On-board Charger: Standard input voltage is
configured at 12V. If a charge voltage greater than 12V is found,
contact your dealer or our service center to replace it with an
applicable charger. An OEM charger must be used.
4. Movement Detection (Motion Detection) and Parking Monitor: Do
not enable this function during driving. When it is enabled, repeated
start/stop recording may affect the integrity of your video.
5. Do not install the device within the range that could be impacted by
airbag or in a location that interferes with the driver’s view or other
safe operation of the vehicle. Make sure it is securely mounted.
3
6. The features described in the operation manual are available for all
products of the same type. Your model may have come with optional
or additional functions. Menu operations may vary. Please refer to the
instructions that apply to your actual product.
Warning
The battery (module or pack) must not be expose to an overheat environment
such as direct sunlight or flame.
Never remove, strike, or squeeze the battery or put it in fire. Stop using the
battery if it is ballooned, warped, leaking, or shows any other visible signs
of damage.
4
Overview
Thank you for choosing REXING! We hope you love your new
products as much as we do.
If you need assistance, or have any suggestions to improve it,
please contact us. You can reach us via [email protected] or call
us at (203) 800 - 4466. Our support team will respond you as soon
as possible.
Always a surprise in Rexing. Check us out here.
https://www.facebook.com/rexingusa/
https://www.instagram.com/rexingdashcam/
https://www.rexingusa.com/support/registration/
Facebook
Instagram
Site
Product Support
5
Table of Contents
Camera Overview..........................................................................6
Installation and Operation……………………………………………….............9
Basic Operations…………………………………………………………..……………12
Mobile Connection…………………………………………………………………….16
GPS Player………………………………………………………………………………….22
Product Specifications……………………………...……………………………….24
General Troubleshooting…………………………...………………………………25
6
Camera Overview
I. Visual Features
(For reference only)
1. Menu/Mode Button
2. Record/Up Button
3. Power Button
4. Down/Toggle Button
5. OK Button
6. Power Cord Connection Port
7. Rearview Camera Connection Port
8. Reset Pinhole
Note: GPS is an optional feature need to connect to the GPS Logger
Buttons and Description:
USB 5V Socket
Smart
Hardwire Kit
Socket
Rearview
Camera Socket
GPS Socket
Front Camera
IR light
Cabin Camera
7
Buttons
Description
M Button
(Menu/Mode
Switch)
1. In standby mode, press this button to start/stop the related
menu options such as recording mode, photography mode,
playback mode.
2. In recording mode, press and hold the button for 3 second to
enter picture-taking and playback interface. Depress it again to
exit.
Record/Up/M
IC Button
1. In standby mode, press this button to start/pause video
recording.
2. Video Mode: Depress this button to start/stop audio
recording.
3. The button is defined for page up in menu setup and playback
mode.
4. During playback, press the button shortly to play fast rewind.
Power Button
1. Press this button to start the device. Depress it for 3 seconds
to power off the device.
2. In power-on state, press the button shortly to turn off/on
screen backlight.
Down/Toggle
Button
1. This button is defined for page down in menu setup and
playback mode.
2. Press this button to switch between front/rear camera view
and PIP display.
3. During playback, press the button shortly to play fast
forward.
4. In video mode, depress the button to switch the IR light to
OFF/ON/AUTO.
OK Button
1. This button functions as a confirmation in each of the setups.
2. In video recording, press this button to start emergency
recording.
3. Depress this button to switch Wi-Fi on/off.
8
4. In photography mode or playback mode, press the button to
take a picture or play back a file.
USB Port
Power charging port/USB data cable port
Power Port
Power cable connection port
Rearview
Camera
Connection
Port
Rearview Camera Connection Port
Reset Pinhole
If the system crashes, use a pin to reset the system.
9
Installation and Operation
1. Turn off the car’s engine.
2. Place the MicroSD card into the slot.
3. Secure the dashcam to a place close to the original rearview mirror.
4. Plug the GPS module into the GPS port and secure the module to a position
close to A-pillar of the car. The antenna receiver side (the side without 3M
adhesive) faces the outside and the side with 3M adhesive faces down. It
should be properly secured.
5. Plug the charger into the car’s cigarette lighter. Connect the device to the
cigarette lighter through the car charger.
Note: The charger extension cable can be wired along the edge of the
windshield during installation. The optional rearview camera should be
mounted on the rear windshield of the car. Pay attention to its orientation
during installation. It can be wired against or above the interior’s headliner.
Plug the rearview camera connector into its rear camera port of the device once
the camera is securely mounted. Adjust the position of the lens to make sure
that it remains horizontal with the ground. Start the engine to check the video
operation of your device.
(This picture is for reference only. Listed articles should referred to your actual
device.)
6. Rearview Camera Wire Routing Illustration (as shown below)
Installation Instructions
Optimum Installation
Location
Power Cable
Wiring Location
10
For the rearview camera, there are two wiring options as shown in the above
figure. The first part of both options is characterized with concealed wire
routing against the edges of the door(s).
A: The rearview camera can be mounted directly above the rear window inside
the car.
B: The rearview camera can be mounted directly above the car’s license plate.
We recommend that you install all components beforehand according to the
above drawing and test the system by using the on-board charger power supply.
Make sure the device is good condition prior to installation. Please, contact our
service center in case of any questions.
Note: The device is configured with a streaming media rearview camera that
provides clear traffic view behind the car. To obtain clearer and more intuitive
images, it is recommended to mount the camera above the license plate (as
shown by option B).
7. Instructions for Reverse Trigger Wiring
The red wire of the car’s reverse gear wiring is connected to the positive end
of one of the car’s reverse light. Make sure that the car charger is energized
during use.
Connection to rearview camera
Re
d
Autres manuels pour S1 Pro
1
Table des matières
Autres manuels Rexing Caméra embarquée
Rexing
Rexing V2 Manuel utilisateur
Rexing
Rexing S1 Manuel utilisateur
Rexing
Rexing MTC1 Manuel utilisateur
Rexing
Rexing V5C Manuel utilisateur
Rexing
Rexing V1 Manuel utilisateur
Rexing
Rexing V2 PRO Manuel utilisateur
Rexing
Rexing V2 Manuel utilisateur
Rexing
Rexing V3 Manuel utilisateur
Rexing
Rexing V1 Manuel utilisateur
Rexing
Rexing V55 Manuel utilisateur
Rexing
Rexing R1 Manuel utilisateur
Rexing
Rexing P1 Manuel utilisateur
Rexing
Rexing V5 Manuel utilisateur
Rexing
Rexing V360 Manuel utilisateur
Rexing
Rexing M1 Manuel utilisateur
Rexing
Rexing V3 Manuel utilisateur
Rexing
Rexing V1P Pro Manuel utilisateur
Rexing
Rexing V1P SE Manuel utilisateur
Rexing
Rexing V1 Manuel utilisateur
Rexing
Rexing V1 Max Manuel utilisateur
