Regency GRAND MARQUIS Manuel utilisateur

• GRAND MARQUIS •

• CEILING FAN OWNER'S MANUAL •

WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.

Style that revolves around you.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

IMPORTANT SAFEGUARDS:

1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly

before beginning.

2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.

To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.

All

electrical connections must be made in accordance with local codes, ordinances and/or the National Electric

Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a

qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling

members and make the proper installation(s) and connections.

3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades

should be at least 7 feet from floor.

4. When mounting on a ceiling outlet box, an approved box UL listed as "suitable for fan support"

"suitable for fan support"

is required. The

box and its supporting members must be able to support the moving weight of the fan's listed weight. The box

must not be able to twist or work loose. Installation on a concrete ceiling should be performed by qualified

personnel.

5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the

carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure

that you do not mix fan blade sets

do not mix fan blade sets

, as each blade is part of a weighted set.

6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one

side of the outlet box, and the "HOT" wires on the other side.

7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and

should be installed per the light kit's installation instructions.

8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling

and/or causing damage or injury.

9. The fan can be made to work immediately after installation - the bearings are adequately charged with grease so

that, under normal conditions, further lubrication should not be necessary for the life of the fan.

10. Do not operate the reverse switch while the fan blades are in motion. The fan must be turned off and the blades

stopped before reversing the blades direction.

11. ATTENTION: Fan includes a 190w limiter to comply with the department of energy 2009 regulation. Lamping

this product over 190w will cause this fan to not light. Please use bulbs with a total wattage under the 190w

regulation.

Weight of Fan: 22.6 Lbs

IMPORTANT SAFETY PRECAUTIONS

• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan

"acceptable for fan

support"

and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support

of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if

in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or

cleaning the fan. Do not insert any object(s) between rotating fan blades.

NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all

possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness

are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring

for, and operating the unit.

Thank you for choosing a Regency Ceiling Fan. You have chosen the best!

Your new ceiling fan has been designed to provide many years of service and enjoyment.

Warnings:

TOOLS AND MATERIALS REQUIRED

• Phillips screwdriver

• Blade screwdriver

• Wrench or pliers

• Wire cutter

• Stepladder

• Wiring supplies as required by

electrical code

UNPACKING YOUR FAN

1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever

necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor

housing on its side, or the decorative housing may shift, be bent or damaged.

2. Examine all parts. You should have the following:

1. Fan blades (5)

2. Hanging bracket

3. Ceiling canopy

4. Canopy screw cover plate

5. Downrod/ball assembly

6. Coupling cover

7. Fan housing with motor (Remove rubber shipping supports around motor, if included on your fan. Save screws.)

8. Blade arms (5)

9. Switch housing

10. Light kit

11. Globe

12. Pull chains with fobs (2)

13. 60W candelabra bulbs (3)

14. Bracket mounting hardware (wood screws, screws, lock washers, washers, wire nuts)

15. Blade arm to blade screws, w/washers (16)

16. "

16. "S

" hook (

Used for hugger style mounting.)

NOTE:

Design of parts shown above may look slightly different for your specific model of fan.

PREPARATION

PREPARATION:

Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor

from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor

box. Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.

Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.

Caution:

To avoid possible electrical shock, be sure

electricity is turned off at the main power box before wiring.

All wiring must be in accordance with National and Local

Electrical Codes and the ceiling fan must be grounded as a

precaution against possible electric shock.

1. Locate ceiling joist where fan is to be mounted, being

sure location agrees with the requirements in the

minimum clearance section of this guide. Wood joist

must be sound and of adequate size to support 35 lbs.

(See Page 1, Items 3 and 4).

2. If not already present, mount a UL listed outlet box

marked "suitable for fan support" following the

instructions provided with the outlet box. The outlet box

must be able to support a minimum of 35 pounds.

3. Attach hanger bracket to outlet box using screws

using screws

provided with the outlet box.

Parts identification on assembled fan

INSTALLING THE HANGING BRACKET

Ceiling Fan

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Spring Washer

Blades

Canopy

Downrod

Motor Housing

Blade Arms

Globe

INSTALLING THE FAN

The HUGGER method is preferred if maximum headroom is required. The ceiling must be horizontal, not sloped.

Blades will be approximately 8' from the ceiling. Air flow will be reduced when the fan is installed using the

HUGGER method.

INSTALLATION:

This fan has two installation options:

#1 HUGGER MOUNTING

The DOWNROD MOUNTING method is preferred if the ceiling is sloped or vaulted, or if the ceiling is extra high

and requires the use of an extension downrod. Blades will be approximately 12' from ceiling using supplied downrod.

#2 DOWNROD MOUNTING

This is the recommended mounting for ceilings 8' and higher.

INSTALLING THE FAN - HUGGER STYLE

NOTE: The S hook is to be used for hugger style mounting.

1. Remove the plastic trim ring from the canopy to expose the 6 mounting holes. The downrod, ball and cotter pin will

not be used for this mounting (Fig. 1).

2. Feed fan wires through the canopy and position the canopy over the mounting collar on top of the fan. The collar's 2

security screws will not be used and can be turned all the way into the collar to make attaching the canopy easier.

3. Align the canopy on top of the fan so the 3 large holes are over the 3 screws holding the collar to the fan. The 3 small

holes will then be aligned with the 3 open holes in the top of the fan.

4. Securely attach the canopy to the top of the fan using the 3 hugger mounting screws provided.

WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling.

5. Place the S hook onto the hanger bracket. Hang the canopy (with the fan motor housing attached) from the S hook on

the hanger bracket using one of the holes in the edge of the canopy (Fig. 2). This will permit you to make the

electrical connections without having to hold the fan up as well.

6. Make the wire connections as described in "Electrical Connections" (page 9).

7. Insert 2 screws into the hanger bracket, leaving them partially out (Fig. 3).

8. Attach the canopy to the hanger bracket by inserting the slotted openings of the canopy on the hanger bracket screws

(Fig. 4), and turn the fan to the right to engage the screws in the slots.

9. Insert the 2 remaining screws through the remaining canopy holes and tighten all 4 screws.

Fig. 1 Screws

6-hole

Canopy

Motor

Housing

Fig. 2

Fig. 3

Fig. 4

NSTALLATION

PTION

#1: H

UGGER

TYLE

OUNTING

S Hook

INSTALLING THE FAN - DOWNROD STYLE

1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out)

facing upward.

2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove

ball.

3. Feed the wires from top of fan through the coupling cover end of downrod and set end of downrod into mounting

collar so the hole in the downrod lines up with the hole in the side of the mounting collar.

4. Insert downrod pin through holes in mounting collar and downrod; slip cotter pin through small hole in end of

downrod pin to hold downrod in place.

5. Tighten security screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod.

Tighten nuts against mounting collar.

NOTE:

Fan has 6 feet of hook-up wire in case

you are using a long extension downrod. Wires

can be cut so only 8 inches or so extend beyond

the top of the downrod to make the electrical

connections easier and safer.

6. Feed wires through canopy and slide canopy

over downrod. It will be attached to ceiling

later.

7. Feed wires through ball and slide ball over

downrod, past hole in the top end of the

downrod. Insert ball pin (removed in step 2),

slide ball up, and tighten set screw to secure

ball in place.

INSTALLATION OPTION #2: DOWNROD STYLE MOUNTING

Ground Wire

(Optional extension shown)

Trim Ring

Hook-up (3) Wires

Ball

Canopy

Downrod

Mounting Collar

Downrod Pin

Collar Cover

Security Screws

Cotter Pin

Top of

Fan Body

INSTALLING THE FAN - DOWNROD STYLE

1. Lift ball/downrod/fan into hanger bracket opening. NOTE:

NOTE:

The tab opposite hanger bracket opening should fit in slot

on ball.

2. Make wire connections, (refer to section titled "Electrical Connections").

3. Slide canopy up and fasten to hanger bracket with 4 screws provided.

WARNING:

To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling.

INSTALLATION OPTION #2: DOWNROD STYLE MOUNTING (CONT.)

Hanger

Bracket Tab

Ball Slot

Ball

ELECTRICAL CONNECTIONS

Be sure electricity is turned off at the main power box before wiring.

1. Four wires are connected to the fan.

Black - this is the "hot" power to run fan.

White - this is the "common" power to run fan and light.

Blue - this is the "hot" power for light kit.

Green - ground wire (on bracket or downrod).

2. If fan and light are to be connected to the same circuit, black and blue wires can both be connected to house circuit

black wire.

NOTE:

The other end of the blue wire, (light circuit) is in the switch housing with a wire nut and label for light kit

attachment. The white wire (common for light kit) is also there.

WARNING:

If light kit is not used, DO NOT connect blue wire at the ceiling.

Fig. 1

Fig. 3

Fig. 2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Regency Ventilateur

Regency

Regency Cayman Manuel utilisateur

Regency

Regency VERA CRUZ Manuel utilisateur

Regency

Regency FE-45A Manuel utilisateur

Regency

Regency Cayman Manuel utilisateur

Regency

Regency BIMINI Manuel utilisateur

Regency

Regency MX Excel Manuel utilisateur

Regency

Regency Deuce Hugger Manuel utilisateur

Regency

Regency GLADIATOR GL3 Manuel utilisateur

Regency

Regency Regatta Manuel utilisateur

Regency

Regency Artiste Manuel utilisateur

Regency

Regency NOLA Manuel utilisateur

Regency

Regency BIMINI Manuel utilisateur

Regency

Regency Celsius Manuel utilisateur

Regency

Regency TROPIC AIR Series Manuel utilisateur

Regency

Regency Quatro Manuel utilisateur

Regency

Regency Mirada Manuel utilisateur

Regency

Regency Marquis Series, Countess Series Manuel utilisateur

Regency

Regency Vantage Manuel utilisateur

Regency

Regency OASIS Manuel utilisateur

Regency

Regency Cabana Manuel utilisateur

Regency

Regency LX Series Manuel utilisateur

Regency

Regency INDY Manuel utilisateur

Regency

Regency Professional Series Manuel utilisateur

Regency

Regency THE INDOOR/OUTDOOR FAN Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage