Record STA20 Manuel utilisateur
RECORD UK DIRECT 25-03-2019 Page 1
Record STA20
RETRO-FIT GUIDE
For the
BESAM SL500
To be read in conjunction with the quick start manual
RECORD UK DIRECT 25-03-2019 Page 2
This Guide has been put together to aid trained personnel in Retro-fitting a Besam SL500
Automatic sliding door operator.
The kit has been designed to replace the Motor and Control mechanism whilst
re-using all the mechanical components such as wheels and track. However some minor
adjustments / adaptions may be required on site.
Please check your sensors etc for compatibility. All safety sensors must be cat C or above
Please refer to the enclosed quick start guide for basic wiring and set up of the STA20
retrofit kit.
Retrofit Adaptation Kit For : (Besam SL500)
Approx Fixing Time : 2-3 hrs
The SL500 series of operators are one of the later generation of sliding door operators.
The original Motor, idler pulley, belt, belt brackets and processor are all replaced.
Before commencing with the installation, please ensure you have the correct kit for the operator make / model
required.
Isolate main voltage and unwire connections to operator.
RECORD UK DIRECT 25-03-2019 Page 3
Due to the size of the header the conversion will entail changing the running plain of the belt from vertical to
horizontal.
Strip out the old motor gearbox, control panel/ power supply idler pulley and belt clamps keeping the fixings .
We recommend that the track is cleaned and checked. We also recommend that the existing load wheels / nylon track
insert are checked and replaced if needed.
It is recommended that the doors are adjusted and aligned before any equipment is installed.
Remember: A badly running manual door = A badly running auto door !!
Commence installation by installing the new motor gearbox to the right hand side of the operator.
The motor comes with a new mounting bracket, this is retained by 2 x existing captive nuts, bolt which are installed into
the groove system in the back of the operator ( see fig 3).
The universal idler pulley should be mounted in the same way on the left of the operator see Fig 4
Fig : 3Fig 4
RECORD UK DIRECT 25-03-2019 Page 4
Replace the existing belt brackets with the new belt brackets, being careful not to dislodge the carriage wheels
and anti riser springs.
Install new control unit module to the left hand side of the motor within distance of motor wiring loom and
connect motor, encoder and if needed the motor lock wires to the processor.
Check all wiring for correct routing and secure with cable ties where ness.
Install the BDED in the required place and plug in.
Your door system is now ready to wire up any sensors / Auxiliary Items to. Please reference the Quick Start Manual
enclosed with this guide.
RECORD UK DIRECT 25-03-2019 Page 5
STA 20 Basic quick set up with record sensors
This Quick Guide is intended for use by trained engineers. If you have not had training on
the equipment then it is possible to set the doors up unsafely.
All automatic door installations should be installed and set up to comply with EN16005
Once you have mechanically fitted, your SLIDE unit follow this guide:
RECORD UK DIRECT 25-03-2019 Page 6
1. Select English, PRESS ENTER (Record) –Then Press (C)
2. Enter programming mode by holding the Blue button on the main processor for 4
Flashes
(If first install it may automatically launch the learn cycle)
3. Select Configure system.
4. Select Door type
5. Select BASIC ESCAPE ROUTE ( this is for all System 20 sliding doors)
6. Return to the first menu screen and select Learning system.
7. Select Running parameters. And then YES
8. Please wait till the door is fully open
9. IF MOTOR DIRECTION IS INCORRECT EITHER SWAP BELT BRACKETS TO REVERSE DOOR
DIRECTION OR CHANGE JUMPER JP4
10.Press and hold the lock symbol until the door is fully closed and the message on
screen changes –Release
11.The door will re-open
12.Press and hold the lock button again until the door is closed –Release the button and
it should then say running parameters complete.
13.Select Continue
It will then ask you if you would like to learn the sensors –if Record sensors are fitted then
Select YES . If third party sensors are fitted select no
RECORD UK DIRECT 25-03-2019 Page 7
28 27 26 25 5 7 6 3 4 11 12
Control Board Connections
N/C
- + can L Can H
+24V 0V AUX01 +24 V AUX00 SSK SSKA
RIC290 AKI
RIC290 AKA
CAN bus
termination
The Fire Alarm Relay is
Located in the same
position as the spur.
An independent
conduit is required –
1st Entry Key
Switch –
N/O
Basic Setup for System 20
N/C fire alarm contact to operate
24hrs all the time.
Safety Opening (SOK)
Program the AUX00 to
SOK/NSK and then the
SOK/NSK menu to SOK
For Open If Not Locked:
Daytime operation only,
programme for Emergency
Opening
CAN BUS
Break Glass
Switch – N/O
If using standard switching side screen safety
sensors then: Program AUX01 to SIO
And then program the SIO configuration for the door
to slow into creep mode upon sensor activation
24hour
Access
Control
Switch – N/O
13A Plug Socket
within 1 meter from
the door on the right
hand side.
Set Address 0 / 0 for AKI
Before Applying Power
Set Address 1 / 0 for AKA
Before Applying Power
Screened Cable BDE
AND / OR Options
System 20 requires
2xRIC290 to cover the
threshold area.
Option 1 can use
standard sensors for
side safety
Option 2 uses the CAN
BUS sensors from
Record
Any more items than
those shown will require
a FEM-0 control board.
Internal Push
To Exit Only
Switch – N/O
The Sensors may be
surface mounted (AC) or
recessed into the cover
(GC).
When recessed into the
cover a 150mm cover is
required
AIS 290
S / Right
AIS 290
S / Left
Set Address 0 / 1
Set Address 0 / 0
RECORD UK DIRECT 25-03-2019 Page 8
1. Fit Sensors. Please see separate manuals supplied with the sensor for full installation and
adjustment details.
2. Set dipswitches so the system knows what type they are –See Below
RIC 290 Dual Threshold and Safety
AKI = Inner Activation AKA = Outer Activation
SI = Inner Threshold Safety SA = Outer Threshold Safety
Most Situations only call for 1x Dual sensor per side of the operator but you can have 2x per side on wider
openings and as such you need to address them. E.g AKA 1 = Outer Sensor 1 & AKA 2 = Outer sensor 2.
AIS290 Side Screen Sensors
SL = Left hand Side Screen Safety sensor SR = Right hand Side Screen Safety sensor
RECORD UK DIRECT 25-03-2019 Page 9
Adjustment of CAN Sensors –All sites are different! It is therefore imperative that the you set up the
individual sensors in compliance with EN16005 and site requirements. As well as the mechanical
adjustments, depth and angle, there are several adjustments to be made via the BDED.
Enter programming mode by holding the Blue button on the processor for 4 Flashes
1. Select Parameter Sensors:
On Activations you can change the sensitivity, and on the Threshold and side screen you can change
the field of detection.
There are several adjustable parameters for each sensor. Please treat the Activation and safety of each
sensor as separate entities.
AKI = internal activation
SI =internal Threshold safety
sssssafetySafety
SR =RH SIDE SCREEN SAFETY
AKA=External activation
SA= Outer threshold safety
SL =LH SIDE SCREEN SAFETY
RECORD UK DIRECT 25-03-2019 Page 10
Sensor Values as a starting point only. Every sensor must be set up and tested for
compliance with EN16005
Activations (AKI & AKA ) –Sensitivity 15
Safety (SI & SA) –Filter –10 or 20
Field Size –3 (BI part)
ROW 1 –ON
ROW 2 –ON
ROW 3 –OFF
If the floor is dark grey or black you may need to remove the X in suppression
-------------------------------------------------------------------------------------
Below is a guide (Birds Eye View) –Of different Threshold safety Fields you can map. To
change to the required field map change the corresponding Number –Default is 0
E.g If you had a narrow door way you may select Map 3 or for No Approach from the Right you
select Map 18
FIELD SIZE S
Now It Is time to set up Your Speeds & running Parameters
Table des matières
Autres manuels Record Système d'ouverture de porte
Record
Record PROTECT RC 2 Manuel utilisateur
Record
Record FlipFlow TWIN Manuel utilisateur
Record
Record STM 20 RED/DUO Manuel utilisateur
Record
Record S20 Series Manuel utilisateur
Record
Record KEANE MONROE 2000 Series Manuel utilisateur
Record
Record C 127 SU S Manuel utilisateur
Record
Record system 20 Manuel de réparation
Record
Record DFA 70 Manuel utilisateur
Record
Record BDE-D Manuel utilisateur
Record
Record R62 Manuel utilisateur
Record
Record DFA 127 Manuel utilisateur
Record
Record K21 Manuel utilisateur
Record
Record C 127 SU OFFSET Manuel utilisateur
Record
Record C 127 X SU H-B OFFSET Manuel utilisateur
Record
Record DFA 127 Guide de configuration
Record
Record C 127 SU H Manuel utilisateur
Record
Record 5100 Series Manuel utilisateur
Record
Record K 32 M Manuel utilisateur
Record
Record 5100 Series Manuel utilisateur
Record
Record K32 ST Manuel utilisateur
