Radcal Dynalyzer IV Manuel utilisateur

RAPIDOSE

Rapid Measurements – with a super small footprint detector

USER GUIDE

DYNALYZER

OPERATION MANUAL

Dynalyzer IV High Voltage Unit

Radcal Corporation

426 West Duarte Road

Monrovia, CA 91016-4591 USA

USA (626) 357-7921

Fax USA (626) 357-8863

email sales@radcal.,com

www.radcal.com

Radcal Part # MNL/ST-4672

4078320 Rev C

Printed: SEPT 2018

Dynalyzer – High Voltage Unit OPERATION MANUAL

Contents

Preface..................................................................................................................................................................3

Safety Notice.....................................................................................................................................................3

Introduction..........................................................................................................................................................4

General..............................................................................................................................................................4

Basic Principle of Operation..............................................................................................................................4

Anode Current Sensor..................................................................................................................................4

High-Voltage Divider.....................................................................................................................................4

Filament Current ...........................................................................................................................................5

Equipment Supplied..........................................................................................................................................5

Specifications ....................................................................................................................................................5

Installation............................................................................................................................................................9

Inspection..........................................................................................................................................................9

Parts Necessary for Use ...................................................................................................................................9

Electrical Connections.......................................................................................................................................9

Precautions...................................................................................................................................................9

High Voltage Cable Connections................................................................................................................10

Operation............................................................................................................................................................15

Readout Oscilloscope .....................................................................................................................................15

Measurement procedure for kVp and Exposure Time Using Oscilloscope................................................15

Measurement Procedures for mA and mAs using Oscilloscope ................................................................16

Three-Phase Current Measurements (using Oscilloscope)........................................................................16

Fluoroscopic Current Measurements (using Oscilloscope)........................................................................17

Measurements with Accu-Dyn+ system (see appendix A)..............................................................................17

Measurements with Digital Display.................................................................................................................17

Current Measurements with Dynalyzer III Digital Display (mA and mAs)...................................................18

Exposure Duration (Time)...........................................................................................................................18

Dynalyzer Digital Display of kVp Measurements........................................................................................18

Filament Current Measurement with the Dynalyzer Digital Display............................................................18

Measurements with Suitable RMS Voltmeter..................................................................................................18

Removing High Voltage Unit from X-ray Installation.......................................................................................19

Interpreting Oscilloscope Measurement Waveforms ......................................................................................19

Single-Phase Current Waveform................................................................................................................19

Three-Phase Current Waveforms...............................................................................................................20

kVp Calibration for X-Ray Generator..........................................................................................................21

Equipment Fault Diagnosis by Voltage Waveform Analysis.......................................................................21

Evaluating Fluoroscopic Current Measurements........................................................................................22

Single-Phase Radiographic Current Measurements using Oscilloscope...................................................23

Filament Current Measurements using Oscilloscope.................................................................................25

Fuse Replacement..........................................................................................................................................27

Maintenance.......................................................................................................................................................27

System Pressure.............................................................................................................................................28

Failure Modes..................................................................................................................................................28

Appendix A.........................................................................................................................................................29

Accu-Dyn+ Display System.............................................................................................................................29

Overview:....................................................................................................................................................29

Installation:..................................................................................................................................................29

Running the Program..................................................................................................................................30

Data.............................................................................................................................................................31

Hotkeys.......................................................................................................................................................31

Common Error Messages:..........................................................................................................................31

Appendix B - Warranties and Disclosures......................................................................................................33

Dynalyzer – High Voltage Unit OPERATION MANUAL

Warranty for the Model M-97311 Dynalyzer High-Voltage Unit ......................................................................33

Non-Warranty Repairs.....................................................................................................................................33

WEEE and RoHS.............................................................................................................................................33

Dynalyzer – High Voltage Unit OPERATION MANUAL

Preface

IMPORTANT: ALWAYS PLUG DYNALYZER, SCOPE, AND

DISPLAY INTO SAME OUTLET.

Safety Notice

This unit is designed to operate at hazardous voltages found in x-ray generators. The operator is

cautioned to observe all safety practices normally associated with x-ray equipment. Among these

precautions are:

1. Never make or break connections in the high voltage circuit when the generator is

energized. In spite of all interlocks present, it is still possible for an accidental firing to

occur.

2. Never assume that a cable voltage is discharged. There is sufficient capacitance in the x-

ray cable to maintain a lethal charge. Touch the pins of any cable to ground to be sure that

there is no residual charge.

3. Inspect cables often. Do not use any cables with a broken braid at the connectors or in the

cable.

4. Always tighten the locking ring of the cable connector to ensure a good ground connection.

Do not overtighten the ring.

5. Use oil or vaporizing compound on all high-voltage connectors to prevent flashover.

6. Keep away from x-ray beam. This system is designed for remote reading so the equipment

should not be placed near the x-ray beam path.

7. Do not knowingly operate this unit in excess of 150 kVp, or in equipment with unstable x-

ray tubes. Severe damage to the equipment may result from an overvoltage condition.

8. Be sure of your grounds. When in doubt, ground tank to transformer.

9. Always monitor tank pressure. Do not use the system if the pressure reads less than 22

psig. Read the maintenance section for refilling or return to the factory.

CAUTION: IMPORTANT HANDLING NOTICE: This unit is a precision high-voltage measurement

instrument and must be handled with as much care as one would handle an

oscilloscope. While it is portable and is designed to sustain normal handling and

transportation shock and vibration, it must not be subjected to excessive shock or

vibration. The precision electronic assemblies contained inside the tank are subject to

damage from abnormal shock transmitted from the heavy flanges on the tank.

Improper handling can cause tank failure and loss of warranty protection.

Dynalyzer – High Voltage Unit OPERATION MANUAL

Introduction

General

The Dynalyzer IV High Voltage Unit is capable of providing isolated signals analogous to:

1. Anode, Cathode, and Anode + Cathode kilovoltages

2. Anode Current

3. Filament Current (AC)

These signals may be viewed on an oscilloscope, may be measured with Accu-Dyn+ system,

peak measuring voltmeter or may be processed and displayed with the Dynalyzer Digital Display

(obsolete).

This unit has been designed as a calibration instrument and as a diagnostic tool for servicing x-ray

equipment.

This unit is designed for continuous duty, and may be left in the high-voltage circuit indefinitely, if

desired. This feature is desirable in special applications where frequent calibration is required.

This unit is portable. It weighs 32 pounds and is designed to simplify servicing and repair.

Basic Principle of Operation

The Dynalyzer High Voltage Unit is built in two sections. All high-voltage components are located

in a tank pressurized with 30 psig of Sulfur Hexafluoride (SF6) gas. In the base of the unit are

power supplies and buffer amplifiers to adjust the levels of the isolated signals, provide buffering

against cable and instrument loading effects, and provide frequency compensation. In addition,

there is an oscillator which in conjunction with a high-frequency isolation transformer located in the

tank, provides power to operate the anode current sensing system.

Anode Current Sensor

The anode current sensor is an optically-coupled device that is capable of providing an isolated

signal that represents the anode current waveform. The sensor is capable of measuring current in

the range of 1 mA to 2 Amperes with a 2% absolute accuracy ± zero offset. The output conversion

factor is 1 mV/mA for radiographic and 20 mV/mA for fluoroscopic measurements. The insertion

impedance of the unit is 42 ohms ± 5%. The average power rating of this resistor network is 40

watts, and is the only duty cycle limitation on this unit. The duration should not exceed 1 second at

1000 mA.

High-Voltage Divider

The divider consists of two 1000 mega-Ohm sections that are connected between the anode and

ground, and cathode and ground. Each section contains five 200 megaohm resistors connected in

series. The geometry of the structure provides distributed capacitance that provides a frequency

response of 100 kHz.

Dynalyzer – High Voltage Unit OPERATION MANUAL

Filament Current

Filament current is measured in the common lead of the cathode circuit using an insulated AC/DC

open loop hall effect current transducer. The output of the transducer is amplified to a signal level

of 0.1 Volt(pp)/Ampere(pp), with a -3-dB bandwidth of 20 kHz.

Equipment Supplied

As supplied, the High Voltage Unit is shipped with the following components:

•High Voltage Unit Assembly

•12 ft. Coaxial Cable, BNC Connectors each end (2 each)

•Vaporproofing Compound (2 [two] 1.5 oz. tubes)

•Line cord (6 ft.)

•Dummy plugs (2)

Additional equipment required for use includes:

•Dual-trace oscilloscope to display mA and kV waveforms

Optionally, a peak holding digital voltmeter (DVM), Dynalyzer III Digital Display or Accu-

Dyn+ system

•Two (2) 3-conductor, 5-foot long high-voltage x-ray cables, Federal Standard Connector

Specifications

Calibration Standard Factory calibrated, all output parameters traceable to National

Bureau of Standards

Electrical Rating (maximum

peak voltages) Anode to cathode: 150 kVp

Anode to ground: 85 kVp

Cathode to ground: 85 kVp

Current from x-ray to

Generator (max) Anode (peak): 1 A for 1 s

Anode (continuous): 700 mA

Filament: 10 amps (ac rms)

D.C. Voltage Division Ration 10,000: 1 ±1% (10kV to 75 kV plus & minus polarity)

Voltage Divider Load 1000 megohms to ground

2000 megohms anode-cathode

Duty Cycle Continuous

Frequency Response Voltage: 0-1 kHz ± 2.9%

1 kHz – 100 kHz ±12.2%

Anode current: 4 kHz @ -3-dB

Filament current: 20 Hz to 20 kHz, ±1db

Filament Current Sensor Output level: 0.1 volt per ampere (p-p)

Ratio: 0.1 volt/ampere (±5% + zero offset)

Noise level: 0.1 ampere, rms

Dynalyzer – High Voltage Unit OPERATION MANUAL

Anode Current Sensor Current rating: 1 A

Insertion impedance: 42 ohms ± 5%

Power rating: 21 watts

Ratio: 1 millivolt/milliampere, (Rad Range)

20 millivolts/milliampere (Fluoro Range)

Accuracy: 1 mA to 1 A, ± 2% (± zero offset)

Noise level: 0.1 mV (p-p) (Max)

Gas Volume 0.5 cubic foot

Pressure Gauge 0-30 psig scale

Insulation Sulfur Hexafluoride gas (SF6) @ 25-30 psig

Gas Relief Valve 32 psig

Gas Filling Valve Schrader type, spring loaded

Test Level Connectors Scope inputs: 5-BNC type, insulated

Accu-Dyn+ computer interface: USB-2.0 mini-B

Digital display: 1-Bendix PT02A-16-8P

High Voltage Receptacles

3-conductor cables Receptacles conform to NEMA XR-7-1979

Coaxial Cable Two 12-foot long cables RG-58/U with BNC connectors

Temperature Operating: +15° to +30°C

Storage: - 10° to + 50°C

Dimensions See Outline Data

Weight 32 lbs (14 kg)

Power Requirements 85-264 V, rms

47-440 Hz

Fuse 250mA SLO-BLO

With Accu-Dyn+ Display System

kV Accuracy ± 1% 10-150 kV, DC to 4.5 kHz

Anode Current ± 0.2% 0.1 mA-1 A, DC to 2.3 kHz

Exposure Time ± 0.5 msec

*Anode+Cathode

Waveforms and calculated kV values reflect a bandwidth of 4.5 kHz

Dynalyzer – High Voltage Unit OPERATION MANUAL

Figure 1: Cabling Data

Dynalyzer – High Voltage Unit OPERATION MANUAL

Figure 2: Outline Data (dimensions in inches)

24.75

22.87

5.19 5.19

8.13

12.90

3.21

1.26

.63

9.00

13°

26°

.37

Table des matières

Autres manuels Radcal Unité de contrôle

Radcal

Radcal Dynalyzer IIIU Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur