QSC Yoke E-Series Manuel utilisateur

E-Series Yoke

Quick Start Guide

E-Series Loudspeakers can be installed using an optional yoke mount, which attaches

to the loudspeaker at the M8 mounting points. A 6 mm hex key is required.

Use the appropriate QSC Yoke Mount Kit for your loudspeakers.

• E10 Yoke

• E12 Yoke

• E15 Yoke

WARNING!:

Consult a structural engineer before mounting the yoke

mount to any surface or structure. Make sure the surface or structure can

support the weight of the loudspeaker and that appropriate fasteners are used

to attach the yoke.

Refer to Figure 1.

1. Select the yoke location and orientation, then properly secure the yoke mounting bracket to the mounting surface. (Attaching hardware is not

included.) The dashed lines show the available yoke positions on the loudspeaker enclosures.

To mount the yoke using cheeseborough clamps, half couplers, or other types of pipe clamp:

◦The E10 or E12 Yoke can mount using one or more clamps.

◦The E15 Yoke must use two clamps.

◦The clamp must have a ½-inch or 10 to 12 mm mounting bolt or stud that is separate from its clamping mechanism; never attach the yoke to

a bolt that is part of the clamping mechanism. The mounting bolt must use a suitable washer and a locking nut. Before reusing a locking nut,

inspect it; replace the nut if its locking insert is worn or damaged.

Refer to Figure 2.

2. Figure 2 shows the top and bottom attachment point for each model. Remove the M8 hex plug in these attachment points.

Refer to Figure 3.

3. Using safe and proper lifting techniques, place the loudspeaker in the yoke, with the two circular pads (5) inserted between the top and bottom of

the loudspeaker enclosure and the yoke.

4. Install the M8 socket head cap screw (1) through the split washer (2),

ﬂat washer (3), yoke (4), pad (5), and into the yoke-mount point

(6). Repeat for the other end of the loudspeaker enclosure. Do not fully

tighten the screws at this point.

5. Adjust the angle of the loudspeaker as required.

6. Tighten the M8 cap screws. Do not overtighten.

Figure 1

Figure 2

Top Bottom

Figure 3

TD-000531-00-A

*TD-000531-00*

TD-000531-00-A

Mailing Address:

QSC, LLC

1675 MacArthur Boulevard

Costa Mesa, CA 92626-1468 USA

Telephone Numbers:

Main Number: +1 (714) 754-6175

Sales & Marketing: +1 (714) 957-7100 or toll free (USA only) (800) 854-4079

Customer Service: +1 (714) 957-7150 or toll free (USA only) (800) 772-2834

Facsimile Numbers:

Sales & Marketing FAX: +1 (714) 754-6174

Customer Service FAX: +1 (714) 754-6173

World Wide Web:

www.qsc.com

E-mail:

[email protected]

Trademark ofﬁce and other countries.. All other trademarks are the property of their respective owners.

http://patents.qsc.com.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels QSC Intervenants

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur