Pyle PLVSHR6 Manuel utilisateur
6 TFT LCD COLOR MONITOR
OPERATING INSTRUCTIONS
Before operating this set, please read these instructions completely
LCD COLOR MONITOR OPERATING INSTRUCTIONS
Congratulations for purchasing our video mobile multimedia
products, before connecting, operating or adjusting this products,
please read these instructions compactly to make your particular
mobile multimedia products to best perform.
1.Do not repair it by yourself, if any trouble occurs, please
immediately shuts it off and contact our company or local dealer.
This monitor is composed of many precise electronic components,
any detachment or reassembling may result damages to the set.
2.Do not exposed it in humid air, dust, vapor, oil lampblack,
sunlight, etc.
3. Do not use thinner or any other chemical cleaner. Please
choose soft cloth to clean the dirt on the monitor.
4. Keep the monitor far from extremely heating or cooling places.
o
Storage temperature: -25~ +60 C
o
Operating temperature: -10- +50 C
5. Prevent the set from falling or struck.
Caution
To ensure security, please do not operate the monitor watch
video or it while driving.
Special hints
There may some blink dots in the screen, it's common
phenomenon in active matrix display technology, but not a
defect or trouble.
1.
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
LCD COLOR MONITOR OPERATING INSTRUCTIONS
Control and layout
Monitor
(1) Adjust Increase
(2) Menu (volume, brightness, color, contrast)
(3) Adjust Decrease
(4) Power on/off
(5) Remote sensor
(6) Audio out (earplug)
(7) Audio / video in
(8) Connecting cord
Remote Control
(1)
(2) Timer switch
(3) Preference switch
(4)
(5) Mute
(6) Memory
(7) Picture up, down, left, right
(8)
(9)
Power on/off
Adjust Decrease
Adjust Increase
Menu (volume, brightness, color, contrast) 2.
8
LCD COLOR MONITOR OPERATING INSTRUCTIONS
Installation
Video output
Audio input (red)
Video input (yellow)
Ground (black)
DC 12V power input (red)
Remote Control replacing batteries
PULL OUT PUSH
3.
1) Always use new batteries when replacing the old set.
2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
3)Battery replacement is necessary when remote control acts sporadically or stops
operating this.
4)Do not drop, apply shock or step on the remote control
5)Do not spill water on the remote control
6) Do not place objects between the remote control and remote sensor.
7)Do not use remote controls for other equipments at the same time.
8)If the MONITOR does not operate even when operating the remote control from
a close range, it is time to replace the batteries (use CR-2025), refer to the label
on back of the basic control.
Operating instructions
LCD COLOR MONITOR OPERATING INSTRUCTIONS
1)Press MODE button to select brightness, contrast and volume
control, press +or - to adjust correspondent analog.
2) Press PP to select the preset analog.
3) Store your favorite
When you have set desired brightness, color, contrast and Volume, press
STORE, then press PP, the screen will display STORE PP, press STORE
again, STORE in screen will turn into green, the moment analog has been
stored, in the future to call out this setting return to the stored state, you only
need to press PP button.
4.
Technical parameters
LCD Drive Method: TFT Active Matrix
Display Size: 6 Inch (diagonal)
Aspect: 4:3
Display Format: 320 x RGB x 234
Number of Pixels: 224,640
Video System Input: NTSC
Back Light: High Brightness Type U Shaped CCFT
Power Source: DC12V
Current Consumption: 8W
Dimensions: 113 x 156 x 26 (mm) w/o headrest kit
Supplied accessories
Wire cord
Stand
Remote control
Headrest bracket
Key
1
1
1
1
2
LCD COLOR MONITOR OPERATING INSTRUCTIONS
5.
Bracket 1
for mounting stand style purpose
Bracket 2
for headrest frame style use purpose
Mounting stand Key- for eject the monitor from
headrest frame
Headrest frame
LCD COLOR MONITOR OPERATING INSTRUCTIONS
6.
Bracket 1
for mounting stand style purpose Bracket 2
for headrest frame style use purpose
Use bracket 2 for headrest frame style
Use bracket 1 for stand sytle
Remove the bracket 2 from the
monitor and install bracket 1 as
folloes diagram for stand style use
液晶彩色顯示器使用說明書
LCD COLOR MONITOR OPERATING INSTRUCTIONS
7.
Step of install headrest frame
Setup work
Measurements
Cut the headrest
Remove the headrest and set it in an
uncluttered work area. Take the appropriate
precautions to ensure that it is not damaged
during the installation.
Push on the headliner with your fingers to make
sure there are no obstructions that would hinder
the installation. Use the paper template to mark
the area to be cut.
Using an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonalyl across, stopping 1/4 inch in
from the other corner, repeat the procedure
for the other two corners.
LCD COLOR MONITOR OPERATING INSTRUCTIONS
8.
Remove form & obsturctions
Route the cable through th e headrest
Install the headrest frame
Carefully peel back the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner or the foam
and use the blade to cut underneath. Remove
small section at a time, using the pull up and
cut method for uniform depth. Use a dremel or
other appropriate tool to remove other
obstructions. Insert the monitor to measure the
fit and make adjustment if necessary
Run the supplied cable through the opening
and out the bottom of the headrest. If possible,
conceal the wires using a shaft covering.
Connect the power, ground and video leads to
test the MONITOR.
Before connecting the monitor, pull the
connecting cable assembly through the
headrest frame as shown in diagram. Place
headrest frame into the opening and secure with
correct fasteners.
Pull the connecting cable through the center of
the frame as shown in diagram, the secure with
correct fasteners
液晶彩色顯示器使用說明書
LCD COLOR MONITOR OPERATING INSTRUCTIONS
9.
Preparing to insert monitor
Inert the monitor
o
Adjust the bracket pin to 90 , run the
cable through the frame as diagram
shown and connect it.
Push to insert the monitor to the
headrest frame
Table des matières
Autres manuels Pyle Système vidéo embarqué
Pyle
Pyle Chopper PLBASS2.8 Manuel utilisateur
Pyle
Pyle PLVSR7B Manuel utilisateur
Pyle
Pyle PLDVD134F Manuel utilisateur
Pyle
Pyle PLDVSL7 Manuel utilisateur
Pyle
Pyle PLVWR840 Manuel utilisateur
Pyle
Pyle PLDVD130 Manuel utilisateur
Pyle
Pyle PLD58MUT Manuel utilisateur
Pyle
Pyle PYLE View Series PLVWR5600 Manuel utilisateur
Pyle
Pyle PLDVD115 Manuel utilisateur
Pyle
Pyle PYLE View Series PLVWR7300 Manuel utilisateur
Pyle
Pyle PLTS79BT Manuel utilisateur
Pyle
Pyle PLDVD120 Manuel utilisateur
Pyle
Pyle PLDVD124 Instructions d'installation
Pyle
Pyle PLD142 Manuel utilisateur
Pyle
Pyle View PLD175TBT Manuel utilisateur
Pyle
Pyle PLCM6000 Manuel utilisateur
Pyle
Pyle PYLE View Series PLTFT72 Manuel utilisateur
Pyle
Pyle PLD162 Manuel utilisateur
Pyle
Pyle PLDN63BT Manuel utilisateur
Pyle
Pyle PYLE View Series PLCM7000 Manuel utilisateur
