Pyle Pro PMX402M Manuel utilisateur
Owner’s Manual
PMX402M 4 CHANNELS
PMX602M 6 CHANNELS
PMX802M 8 CHANNELS
www.pyleaudio.com
_________________________________________________________- 2 -_________________________________________________
FEATURES
Balanced microphone inputs, high impedance microphone/line Inputs and
Tape/CD inputs. All may be used simultaneously reverb built in with individual control
on each channel line out for connection to external amplifiers record out jack for taping
performances R.F interference protection on all inputs and outputs.
The family of products built-in high-quality, high-effect of MP3 players can play in
the USB disk MP3 format songs. Blue backlit LCD display screen can display the total
number of songs in the USB disk, songs of the total play time ,play time at present, play
/ stop sign, symbol cycle, as well as the EQ. Through four key touch with LCD display
is easy to operate MP3 player.
SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of electrical shock, do not
remove the cover (or back). No user serviceable parts
inside; refer servicing to qualified personnel.
WARNING: To reduce the risk of fire or electrical shock, do not
expose this appliance to rain or moisture.
This symbol, wherever it appears,
alerts you to the presence of
uninsulated dangerous voltage
inside the enclosure-voltage that
may be sufficient to constitute a
risk of shock.
This symbol, wherever it appears,
alerts you to important operating
and maintenance instructions in
the accompanying literature. Read
the manual.
_________________________________________________________- 3 -_________________________________________________
A. FRONT PANEL SECTION FEATURES
1. BALANCE INPUT (MIC)
Electronic Balanced inputs acceptable a standard XLR male connector. It is designed to accept a
balanced low impedance input signal, Phantom power (15 volts) for condenser microphones is always
on and available. It has an input impedance of 1K ohm. The connector is wired as: Pin= shield ;
Pin3= negative(cold).
2. BALANCE INPUT(LINE)
Electronic Balanced inputs acceptable a standard 1/4＂jacks connector. It is designed to accept a
balanced high impedance input signal (This use for connection Deck , Turntable, Keyboard etc…).
3. VOLUME
This is function to adjust the volume of signal connection into each channel and adjust the
volume of output, together with master fader.
4. TREBLE
This control gives you up to 15 db of boost or cut at 10 kHz and above, and it is also flat at the
detent. Use it to add sizzle to cymbals, and an overall sense of transparency or edge to key-boards,
vocals, guitar, and bacon frying. Turn it down a little to reduce sibilance, or to hide tape hiss.
5. LOW FREQUENCY
This control gives you up to 15 dB boost or cut at 100Hz and below. This circuit is flat (no boost
or cut) at the center detent position. This frequency represents the punch in bass drums, bass guitar, fat
synch patches, and some really serious male singers.
6. REVERB DEPTH/EFFECT BALANCE
This is a send control to the reverb buss, It controls the amount of reverberation added to the
Input signals.
_________________________________________________________- 4 -_________________________________________________
7. GRAPHIC EQUALIZER
2×5-band equalizer is provided for tone control over each frequency , and for precise high
quality sound by final tone control. It can control main channel and record
channel.( 60,250,1K,2K,8KHz ) shelving at +/-12dB.
8. LCD DISPLAY(There are three states show)
a. Machine became the first LCD display screen information are the trademarks of
products, USB version, and initial system.
b. The second message is to remind the screen insert USB disk, or disk is not MP3
format.
c. The third message is the total number of songs in the USB disk, songs of the total
play time ,play time at present, play/pause/ stop sign, symbol cycle, File Format(M
refers to the MP3 file format, W refers to the WMA file format), as well as the EQ.
9. TOUCH BUTTON
Four touch keys, which are single cycle / circle of the total, up , play /pause / stop,
down, EQ option. All of the touch button of this machine are conventional key and
compound key.
a. Symbol cycle (A total of 6 cycle model) they are All cycle , random play ,song cycle ,
End the end of the single player , cycle by a player and players here. Through the
button to switch modes, according to a time switch, LCD display the logo.
b. Down This is a complex bond, In the state of play, press the button, Will play on a
song; In the state to suspend or stop, press the button, the current song will be
re-broadcast; Press the button for a long time, can adjust the LCD backlight
brightness.
c. Play /Pause/ Stop This is a Multi-Function control, the press is a player, next it is
time to pause, then it is stop, while the corresponding LCD display signs. Press for a
long time, null and void.
_________________________________________________________- 5 -_________________________________________________
d. Up This is a multi-function control, In the state of play, press the button,
Will play the next song; Press the button for a long time, can adjust the LCD
backlight brightness.
e. EQ This is a conventional keys, press the first choice of a EQ, a total of 11 EQ, are
Natural, Rock, Pop, Class, Jazz, Blue, Hall, Bass, Soft, Country, and Opera.
10.POWER LED
It lights when power switch turn on.
11. PHANTOM LED
The LED +15V will be turned on when start working.
12. PHANTOM POWER SWITCH
When it is depressed, the XLR jack input has +15V voltage.
13. OUTPUTS LEVEL INDICATOR
This is level meter which shows output levels of left & right channel condition on the way of
operation, therefore, you can see output condition thru this master level indication.
.14. MASTER VOLUME
Using by this control, you can adjust signal level of main channel.
15. TAPE
This controls the level of the playback inputs(RCA) jack.
16. USB DISK
USB disk insert jack.
17. MP3
Using by this control, you can adjust MP3 signal level send to main channel.
18. REVERB EFFECTS DELAY
Using by this control, you can adjust the delay time interval of echo repeat.
19. REVERB EFFECTS REPEAT
Using by this control , you can adjust reverberating deepness.
20. REVERB EFFECTS LEVEL
Using by this control, you can adjust signal level of echo output.
_________________________________________________________- 6 -_________________________________________________
B. BACK PANEL SECTION FEATURES
1. SPEAKER JACK (LEFT/RIGHT)
These are 2 conductor 1/4” speaker outputs. Each one is rated at 8 ohm minimum impedance.
Total minimum load for the amplifier is 4 ohms. You may connect either 1-4 ohm. 1-8 ohm or 2-8
ohm speaker cabinets. Do not below rated minimum impedance.
2. SEND/RETURN
Using by this jack, you can use stereo 1/4＂jacks connector send internal signal which before
power amplifier to external effects processing, after processing return to internal power amplifier.
Or you can use stereo or mono 1/4＂jacks connector send external signal to inner power amplifier .
3.TAPE INPUT
These RCA jacks are for brining in a tape deck, CD play or other line level source. The
impedance is 10k ohms .
4. REC OUTPUT
These RCA jacks are for hooking up a tape desk to record from the mixer. Both channel are
summed into mono for compatibility. The signals are taken pre-master section, meaning that they are
without reverb or the master tone section, and does not include the Tape in signal, The impedance is
1K ohms @ -10dBv.
5. FAN
In order to prevent rising the inside temperature, the inside heat is emitted outside.
6. POWER SWITCH
When you want to operate, turn on it, then the LED will be turned on .
_________________________________________________________- 7 -_________________________________________________
7. CHANGE-OVER SWITCH
This device is used to 110V/220V or 115V/230V voltage conversion.
8. AC POWER CORD/FUSE HOLDERS
AC 220～240V 60Hz or 110-120V 60Hz ,Check the power voltage of supply with silk-screen of
the panel before connections. When occur a problem on this appliance, the fuse will be cut off, power
to prevent form a problem.
C. CONNECTIONS
You will need a lot of cables for different purposes – see the following figures to make sure you
have got the right ones. Unbalanced equipment may be connected to balanced inputs/outputs. Either
use mono 1/4＂jacks or connect ring and sleeve of TRS jacks.
Fig. 5: Balance plug
_________________________________________________________- 8 -_________________________________________________
Bandwidth 20Hzto20kHz_+1dB
InputImpedance: Lo-ZMic 1Kohms
Hi-ZMic/Line 33Kohms
Tape playback 10Kohms
Inputlevel: Lo-ZMic -50dB
Hi-ZMic/Line -20dB
Tapeplayback -10dB
Recoutputlevel +22dB(max)
MODEL NO PMX402M PMX602M PMX802M
CHANNELS 4CHANNELS 6CHANNELS 8CHANNELS
POWER 400W 600W 800W
DIMENSION 15.75’X12.01’X7.87’ 17.32’X12.01’X7.87’ 20.28X12.01’X7.87’
Specifications:
*With USB 2.0 Terminal and LCD
*5-Band graphic equalizer
*Each channel tone control
*Effect control
*TAPE input, REC output
*Channel tone adjust (high/low+/-15dB)
*AUX/TAPE/effect feedback input
*Effect send
*Master volume control
*Phantom + 15V
Power supply 110VAC 60HZ，SWITCHABLE 220VAC 50HZ
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Pyle Pro Amplificateur
Pyle Pro
Pyle Pro Waisband Amplifier PWMA30 Manuel utilisateur
Pyle Pro
Pyle Pro PYLE PT-680A Manuel utilisateur
Pyle Pro
Pyle Pro P1501ATU Manuel utilisateur
Pyle Pro
Pyle Pro PCAU48BT Manuel utilisateur
Pyle Pro
Pyle Pro PSA2000 Manuel utilisateur
Pyle Pro
Pyle Pro PPA200 Manuel utilisateur
Pyle Pro
Pyle Pro PWMA600 Manuel utilisateur
Pyle Pro
Pyle Pro PD950A Manuel utilisateur
Pyle Pro
Pyle Pro PT910 Manuel utilisateur
Pyle Pro
Pyle Pro PEA4000 Manuel utilisateur
Pyle Pro
Pyle Pro PT-1201X Manuel utilisateur
Pyle Pro
Pyle Pro PYLE PRO P1001AT Manuel utilisateur
Pyle Pro
Pyle Pro PDG2000 Manuel utilisateur
Pyle Pro
Pyle Pro PYLE PRO amplifier PT-1100/PT3300 Manuel utilisateur
Pyle Pro
Pyle Pro PTA1000 Manuel utilisateur
Pyle Pro
Pyle Pro PWMA600 Manuel utilisateur
Pyle Pro
Pyle Pro Amplifier PT-5800 Manuel utilisateur
Pyle Pro
Pyle Pro PD750A Manuel utilisateur
Pyle Pro
Pyle Pro PTA1 Manuel utilisateur
Pyle Pro
Pyle Pro PT610 Manuel utilisateur
