Pure Aqua WS1TC Instructions de montage

TO SET CURRENT TIME OF DAY:

PRESS SET HOUR AND USING UP OR DOWN ARROW BUTTONS, ADJUST

TO CURRENT HOUR.

PRESS SET HOUR AND USING UP OR DOWN ARROW BUTTONS, ADJUST

TO CURRENT MINUTES TO THE HOUR.

PRESS: SET HOUR BUTTON TO RETURN TO NORMAL SERVICE MODE.

TO BACKWASH IMMEDIATELY:

PRESS UP AND DOWN ARROW BUTTONS TOGETHER AND HOLD FOR 3

SECONDS -BACKWASH WILL START IMMEDIATELY.

TO BACKWASH WITHIN 24 HOURS AT THE PRESET TIME OF DAY:

PRESS UP AND DOWN ARROW BUTTONS TOGETHER AND RELEASE -

BACKWASH WILL START AT THE PREPROGRAMMED TIME.

NOTE: "SET HOUR" IS NOW "SET"

TO ENTER BASIC PROGRAMMING MODE:

PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER FOR 3 SECONDS

USE UP OR DOWN ARROW BUTTONSTO SET THE PREFERRED HOUR

FOR THE START OF BACKWASH (DEFAULT = 2:00 AM)

PRESS: SET HOUR BUTTON

USE UP OR DOWN ARROW BUTTONSTO SET THE PREFERRED MINUTE

FOR THE START OF BACKWASH (DEFAULT= 2:00 AM)

PRESS SET HOUR BUTTON: USEUP OR DOWN ARROW BUTTONS TO

SELECT THE FREQUENCY BETWEEN BACKWASHES IN DAYS. (DEFAULT =

7DAYS)

TO ENTER MASTER PROGRAMMING MODE:

PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER FOR 3 SECONDS

AND RELEASE

PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER AGAIN FOR 3

SECONDS

USE UP OR DOWN ARROW BUTTONS TO CHOOSE:

P7: MINIMAL BACKWASH

P8: STANDARD BACKWASH (DEFAULT SETTING)

P9: EXTENDED BACKWASH

PRESS: SET HOUR BUTTON; CHOOSE “99”

PRESS: SET HOUR BUTTON; CHOOSE “60”

PRESS: SET HOUR BUTTON; CHOOSE “dp” WITH ARROW POINTED AT

“REGEN HOUR”

PRESS SET HOUR BUTTON TO RETURN TO NORMAL SERVICE MODE

INSTALLATION AND PROGRAMMING PROCEDURES

INSTALLATION AND STARTUP

1. System should installed by a licensed contractor, complying with all local and

federal codes and using quality materials to insure proper operation.

2. Install system. Be certain the inlet and outlet are properly connected.

3. Place bypass valve in “Bypass Position” with valve handles perpendicular to

the inlet and outlet.

4. Fully open the *test spigot (if installed) at the outlet of the system, or open a high

flow COLD water fixture, like a tub. DO NOT use any other water in house at this

time, including hot water and toilets. *Does not apply if using test spigot.

5. Place bypass valve into “Service Position” with valve handles parallel to each

other and the inlet and outlet.

6. Allow water to run through the open fixture or test spigot for 15-20 minutes

Observe the water flow for color. If after 20 minutes color from the media

is still present, allow system flow to continue until clear.

7. Close fixture or test spigot to stop water flow.

8. Initiate Manual Backwash of the CrystalClear Interior.

9. Observe visually and/or audibly the Backwash Flow (Cycle 1) for any reduction

of flow to drain. Backwash should maintain constant flow and sound.

10. If the backwash flow starts strong but diminishes start a new manual

backwash and allow backwash to complete and system to return to

service mode automatically.

11. If backwash flow is normal, allow the backwash process to complete

automatically.

12. If reduction in backwash flow is observed, repeat steps 5 through 10 until

backwash operates normally.

13. Finally, fully open a cold-water fixture and insure service flow is adequate.

14. If a reduction in service flow is observed, repeat steps 5 through 10 until

household service flow is normal.

15. With backwash and service flow adequate, set time of day on the control

valve by using the up and down buttons. Installation and verification are

complete.

Notes:

A. Check static (no water flowing) water pressure in pounds per

square inch (psi) using an accurate gauge, as close to the water

main as possible. Water pressure less than 40 psi may present

problems with the Healthy Home service flow, and compromising

the backwashing capability of the system.

B. Any addition to household plumbing can cause a drop in pressure

and/or flow rates. Great care has been taken in the design of the

Healthy Home to minimize these affects.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pure Aqua Unité de contrôle

Pure Aqua

Pure Aqua Fleck 1500 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur