ProSoft Technology ProLinx DNPS Manuel utilisateur

ProLinx DNPS

ProLinx Gateway

DNP 3.0 Slave

December 01, 2009

USER MANUAL

Important Installation Instructions

Power, Input, and Output (I/O) wiring must be in accordance with Class I, Division 2 wiring methods, Article 501-4 (b)

of the National Electrical Code, NFPA 70 for installation in the U.S., or as specified in Section 18-1J2 of the Canadian

Electrical Code for installations in Canada, and in accordance with the authority having jurisdiction. The following

warnings must be heeded:

A WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIV. 2;

B WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE

REPLACING OR WIRING MODULES

C WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN

SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.

D THIS DEVICE SHALL BE POWERED BY CLASS 2 OUTPUTS ONLY.

All ProLinx®Products

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN

SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

AVERTISSEMENT – RISQUE D'EXPLOSION – AVANT DE DÉCONNECTER L'EQUIPMENT, COUPER LE

COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DÉSIGNÉ NON DANGEREUX.

Markings

UL/cUL ISA 12.12.01 Class I, Div 2 Groups A, B, C, D

cUL C22.2 No. 213-M1987

243333 183151

CL I Div 2 GPs A, B, C, D

Temp Code T5

II 3 G

Ex nA nL IIC T5 X

0° C <= Ta <= 60° C

II – Equipment intended for above ground use (not for use in mines).

3 – Category 3 equipment, investigated for normal operation only.

G – Equipment protected against explosive gasses.

ProLinx Gateways with Ethernet Ports

Series C ProLinx™ Gateways with Ethernet ports do NOT include the HTML Web Server. The HTML Web Server

must be ordered as an option. This option requires a factory-installed hardware addition. The HTML Web Server now

supports:

8 MB file storage for HTML files and associated graphics files (previously limited to 384K)

32K maximum HTML page size (previously limited to 16K)

To upgrade a previously purchased Series C model:

Contact your ProSoft Technology distributor to order the upgrade and obtain a Returned Merchandise Authorization

(RMA) to return the unit to ProSoft Technology.

To Order a ProLinx Plus gateway with the -WEB option:

Add -WEB to the standard ProLinx part number. For example, 5201-MNET-MCM-WEB.

Your Feedback Please

We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,

compliments or complaints about the product, documentation, or support, please write or call us.

ProSoft Technology

5201 Truxtun Ave., 3rd Floor

Bakersfield, CA 93309

+1 (661) 716-5100

+1 (661) 716-5101 (Fax)

www.prosoft-technology.com

support@prosoft-technology.com

ProLinx DNPS User Manual

December 01, 2009

ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk®, and RadioLinx ®are Registered Trademarks of ProSoft

Technology, Inc. All other brand or product names are or may be trademarks of, and are used to identify products

and services of, their respective owners.

ProSoft Technology®Product Documentation

In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product shipments.

User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided on the enclosed CD-ROM,

and are available at no charge from our web site: www.prosoft-technology.com

Printed documentation is available for purchase. Contact ProSoft Technology for pricing and availability.

North America: +1.661.716.5100

Asia Pacific: +603.7724.2080

Europe, Middle East, Africa: +33 (0) 5.3436.87.20

Latin America: +1.281.298.9109

Contents ProLinx DNPS ♦ProLinx Gateway

User Manual DNP 3.0 Slave

ProSoft Technology, Inc. Page 5 of 86

December 1, 2009

Contents

Important Installation Instructions.......................................................................................................2

Your Feedback Please........................................................................................................................3

ProSoft Technology®Product Documentation....................................................................................3

Guide to the ProLinx DNPS User Manual 7

1Start Here 9

1.1 ProLinx Reference Guide..........................................................................................9

1.2 Install ProSoft Configuration Builder Software..........................................................9

1.3 Using ProSoft Configuration Builder .......................................................................10

1.4 DNPS Protocol Configuration..................................................................................14

1.5 Download the Project to the Module.......................................................................28

2Diagnostics and Troubleshooting 31

2.1 Requirements..........................................................................................................31

2.2 LED Indicators.........................................................................................................35

2.3 Serial Port DNPS Error and Status Data.................................................................36

3Reference 41

3.1 Product Specifications.............................................................................................41

3.2 Communication Port Cables....................................................................................44

3.3 Functional Overview................................................................................................50

3.4 DNP Collision Avoidance ........................................................................................64

3.5 IIN Response: Slave Port........................................................................................65

3.6 IIN Bit Definitions.....................................................................................................66

3.7 Event Size Computation..........................................................................................67

3.8 Device Profile..........................................................................................................68

3.9 Subset Definition.....................................................................................................70

4Support, Service & Warranty 79

4.1 How to Contact Us: Technical Support...................................................................79

4.2 Return Material Authorization (RMA) Policies and Conditions................................80

4.3 LIMITED WARRANTY.............................................................................................81

Index 85

ProLinx DNPS ♦ProLinx Gateway Contents

DNP 3.0 Slave User Manual

Page 6 of 86 ProSoft Technology, Inc.

December 1, 2009

Start Here ProLinx DNPS ♦ProLinx Gateway

User Manual DNP 3.0 Slave

ProSoft Technology, Inc. Page 7 of 86

December 1, 2009

Guide to the ProLinx DNPS User Manual

Function Section to Read Details

Introduction

(Must Do)

→Start Here (page 9) This Section introduces the customer to the

gateway. Included are: package contents,

system requirements, hardware installation, and

basic configuration.

Diagnostic and

Troubleshooting →Diagnostics and

Troubleshooting

(page 31)

This section describes Diagnostic and

Troubleshooting procedures.

Reference

Product Specifications

Functional Overview

→Reference (page 41)

Functional Overview

(page 50)

Product

Specifications (page

41)

These sections contain general references

associated with this product, Specifications, and

the Functional Overview.

Support, Service, and

Warranty

Index

→Support, Service

and Warranty (page

79)

This section contains Support, Service and

Warranty information.

Index of chapters.

ProLinx DNPS ♦ProLinx Gateway Start Here

DNP 3.0 Slave User Manual

Page 8 of 86 ProSoft Technology, Inc.

December 1, 2009

Start Here ProLinx DNPS ♦ProLinx Gateway

User Manual DNP 3.0 Slave

ProSoft Technology, Inc. Page 9 of 86

December 1, 2009

1 Start Here

In This Chapter

ProLinx Reference Guide........................................................................9

Install ProSoft Configuration Builder Software.........................................9

Using ProSoft Configuration Builder......................................................10

DNPS Protocol Configuration................................................................14

Download the Project to the Module......................................................28

For most applications, the installation and configuration steps described in this

section will work without additional programming. ProSoft Technology strongly

recommends that you complete the steps in this chapter before developing a

custom application.

1.1 ProLinx Reference Guide

The ProLinx Reference Guide on the ProSoft Solutions CD-ROM provides

detailed information on the entire range of ProLinx modules. If you have any

questions that are not answered in the DNPS User Manual, please refer to the

ProLinx Reference Guide.

1.2 Install ProSoft Configuration Builder Software

You must install the ProSoft Configuration Builder (PCB) software to configure

the gateway. You can always get the newest version of ProSoft Configuration

Builder from the ProSoft Technology web site.

To install ProSoft Configuration Builder from the ProSoft Web Site

1 Open your web browser and navigate to http://www.prosoft-

technology.com/pcb

2 Click the DOWNLOAD HERE link to download the latest version of ProSoft

Configuration Builder.

3 Choose "SAVE"or "SAVE FILE"when prompted.

4 Save the file to your Windows Desktop, so that you can find it easily when

you have finished downloading.

5 When the download is complete, locate and open the file, and then follow the

instructions on your screen to install the program.

If you do not have access to the Internet, you can install ProSoft Configuration

Builder from the ProSoft Solutions CD-ROM, included in the package with your

gateway.

ProLinx DNPS ♦ProLinx Gateway Start Here

DNP 3.0 Slave User Manual

Page 10 of 86 ProSoft Technology, Inc.

December 1, 2009

To install ProSoft Configuration Builder from the Product CD-ROM

1 Insert the ProSoft Solutions Product CD-ROM into the CD-ROM drive of your

PC. Wait for the startup screen to appear.

2 On the startup screen, click PRODUCT DOCUMENTATION. This action opens a

Windows Explorer file tree window.

3 Click to open the UTILITIES folder. This folder contains all of the applications

and files you will need to set up and configure your gateway.

4 Double-click the SETUPCONFIGURATIONTOOL folder, double-click the

"PCB_*.EXE"file and follow the instructions on your screen to install the

software on your PC. The information represented by the "*" character in the

file name is the PCB version number and, therefore, subject to change as

new versions of PCB are released.

Note: Many of the configuration and maintenance procedures use files and other utilities on the

CD-ROM. You may wish to copy the files from the Utilities folder on the CD-ROM to a convenient

location on your hard drive.

1.2.1 Using the Online Help

Most of the information needed to help you use ProSoft Configuration Builder is

provided in a Help System that is always available whenever you are running

ProSoft Configuration Builder. The Help System does not require an Internet

connection.

To view the help pages, start ProSoft Configuration Builder, open the HELP

menu, and then choose CONTENTS.

1.3 Using ProSoft Configuration Builder

ProSoft Configuration Builder (PCB) provides a quick and easy way to manage

gateway configuration files customized to meet your application needs. PCB is

not only a powerful solution for new configuration files, but also allows you to

import information from previously installed (known working) configurations to

new projects.

Table des matières

Autres manuels ProSoft Technology Porte

ProSoft Technology

ProSoft Technology ICX35-HWC Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX51-PBS Manuel utilisateur

ProSoft Technology

ProSoft Technology RLXIC-EH Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX51-PBM Manuel utilisateur

ProSoft Technology

ProSoft Technology ProSoft 1560 Manuel utilisateur

ProSoft Technology

ProSoft Technology ICX35-HWC Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX82-EIP-PNC Manuel utilisateur

ProSoft Technology

ProSoft Technology ProLinx 5604-RIO-PDPMV1 Manuel utilisateur

ProSoft Technology

ProSoft Technology ICX30-HWC Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX3 Series Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX3x Series Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX30 Series Manuel utilisateur

ProSoft Technology

ProSoft Technology PLX51-PBM Manuel utilisateur

ProSoft Technology

ProSoft Technology ProLinx S3964R Note de version

ProSoft Technology

ProSoft Technology ProLinx-HART Note de version

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur