Prorack K931 Manuel utilisateur
K931
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
Revision No: 3C 1
Fitting Kit K931
MAX kgs (lbs)
W/P WHD
Kia
Rio LX, 4dr Sedan 06-11 US 50 kgs (110 lbs) 50 kgs (110 lbs)
Rio, 4dr Sedan 05-11 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Rio, 4dr Sedan 05-11 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Rio, 4dr Sedan 05-11 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Rio, 4dr Sedan 05-11 CN 50 kgs (110 lbs) 50 kgs (110 lbs)
Rio, 5dr Hatch Aug 05-Aug 11 AU 60 kgs (132 lbs) 60 kgs (132 lbs)
Rio, 5dr Hatch Aug 05-Aug 11 EU 60 kgs (132 lbs) 60 kgs (132 lbs)
Rio, 5dr Hatch Aug 05-Aug 11 NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Rio, 5dr Hatch Aug 05-Aug 11 ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
Rio, 5dr Hatch Aug 05-Aug 11 US 60 kgs (132 lbs) 60 kgs (132 lbs)
2
Fitting Kit K931
X
A B C 1 2 3
Rio LX, 4dr Sedan 06-11 (US) -265mm 395mm - 823mm 810mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 7/8ths" -
Rio, 4dr Sedan 05-11 (AU) -265mm 395mm - 823mm 810mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 7/8ths" -
Rio, 4dr Sedan 05-11 (NZ) -265mm 395mm - 823mm 810mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 7/8ths" -
Rio, 4dr Sedan 05-11 (ZA) -265mm 395mm - 823mm 810mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 7/8ths" -
Rio, 4dr Sedan 05-11 (CN) -265mm 395mm - 823mm 810mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 7/8ths" -
Rio, 5dr Hatch Aug 05-Aug 11 (AU) -265mm 395mm - 823mm 797mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 3/8ths" -
Rio, 5dr Hatch Aug 05-Aug 11 (EU) -265mm 395mm - 823mm 797mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 3/8ths" -
Rio, 5dr Hatch Aug 05-Aug 11 (NZ) -265mm 395mm - 823mm 797mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 3/8ths" -
Rio, 5dr Hatch Aug 05-Aug 11 (ZA) -265mm 395mm - 823mm 797mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 3/8ths" -
Rio, 5dr Hatch Aug 05-Aug 11 (US) -265mm 395mm - 823mm 797mm -
-10 -7/16ths" 15 9/16ths" - 32 3/8ths" 31 3/8ths" -
3
Fitting Kit EN
K931
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K931
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K931
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A674
B = A675
C = A676
D = A677
6
Fitting Kit EN
K931
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K931
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 250
B = 251
C = 295
D = 296
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K931
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
9
Fitting Kit EN
K931
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Table des matières
Autres manuels Prorack Accessoires automobiles
Prorack
Prorack K705 Manuel d'utilisation et d'installation
Prorack
Prorack K077 Manuel utilisateur
Prorack
Prorack K758 Manuel utilisateur
Prorack
Prorack K052 Manuel utilisateur
Prorack
Prorack K1018 Manuel utilisateur
Prorack
Prorack K1012 Manuel utilisateur
Prorack
Prorack K104 Manuel utilisateur
Prorack
Prorack Fitting Kit K722 Manuel d'utilisation et d'installation
Prorack
Prorack K513 Manuel utilisateur
Prorack
Prorack K683 Manuel utilisateur
Prorack
Prorack K564 Manuel utilisateur
Prorack
Prorack K782 Manuel d'utilisation et d'installation
Prorack
Prorack K485 Manuel utilisateur
Prorack
Prorack K358 Manuel utilisateur
Prorack
Prorack K412 Manuel utilisateur
Prorack
Prorack S16 Manuel utilisateur
Prorack
Prorack K646 Manuel utilisateur
Prorack
Prorack K600 Manuel utilisateur
Prorack
Prorack K1153 Manuel utilisateur
Prorack
Prorack TP1 Manuel utilisateur
