ProMinent DCM 5 Series Manuel utilisateur

Visit our XTRANET <www.prominentxtranet.com> to:

• sign up for our electronic newsletter • download literature and manuals • validate your product warranty

BACK ENTER

ProMinent®

ALARM Pool 750.0mV

7.40pH 85.0F

BACK ENTER

ProMinent®

ALARM Pool 750.0mV

7.40pH 85.0F

BACK ENTER

ProMinent®

ALARM

ENT

Editing, or Exit

7.40 pH

BACK ENTER

ProMinent®

ALARM

ENT

Oxidant Pump_3 3

OFF: ppm control

BACK ENTER

ProMinent®

ALARM

ENT

Editing, or Exit

7.40 pH

BACK ENTER

ProMinent®

ALARM

ENT

Editing, or Exit

1.40 pH

BACK ENTER

ProMinent®

ALARM

pH Sensor A

7.40 pH

BACK ENTER

ProMinent®

ALARM

ENT

Editing, or Exit

1.50 pH

CAUTION

Before attempting calibration or commissioning of the DCM5 controller, water chemistry must be stable and within normal ranges

of 7.2-7.8 pH, Total Alkalinity 80-120 ppm, Free Chlorine 1-2 ppm

pH Calibration Adjusting Pump Setpoints

(Residual and Temperature calibrations are performed in the same

manner from their respective sensor menus, but eld ORP calibrations

are not normally needed.)

1. Perform a pH test and NOTE the results Note: “Turn OFF Setpoint” is the ideal point where chemical

control is achieved and “Turn ON Setpoint” is the point used to

dene the on/off deadband or proportional span needed.

2. Press 2 times

[Oxidant]

[pH Sensor_C] 1. Press 5 times

[pool Oxidant]

[pH Sensor]

[Acid Pump]

[ORP Sensor_D]

[Oxidant Pump_3]

3. Press 3 times

[Editing, ⏎ or Exit]

[Calibrate]

[Enter Value]

2. Press 3 times to

change the Turn ON

Setpoint [Editing, ⏎

or Exit]

4. Press to

adjust displayed value

to match the tested

value, then press

to accept the change

3. Press to

adjust the Turn ON

Setpoint, usually one

or two units (0.1 ppm)

below the Turn OFF

setpoint for Oxidant

feed systems. Then

press to accept the

new value.

5. Press to return

to the main status

screen

5. Press to

adjust the “Turn OFF

Setpoint”. This is the

point where oxidant

feed is satised, and

considered by most to

be the setpoint when

only 1 setponit is

used. Then press

to accept the new

value.

4. Press then to

change the Turn OFF

Setpoint. (Default is

1.5ppm)

6. Pressing BACK returns to the main status screen

DCM5_QSG.indd Rev1 (09/25/2012)(p/n: 7500581)

DCM 5 Series Controller

Quick Start Guide

BACK ENTER

ProMinent®

ALARM Pool 750.0mV

7.40pH 85.0F

BACK ENTER

ProMinent®

ALARM Pool 750.0mV

7.40pH 85.0F

BACK ENTER

ProMinent®

ALARM Pool Oxidant

OFF: Setpoints

BACK ENTER

ProMinent®

ALARM Oxidant Pump 3

OFF: Setpoints

BACK ENTER

ProMinent®

ALARM Alarms

A B 1 2

BACK ENTER

ProMinent®

ALARM

ENTER

Oxidant Pump 3

Auto OFF ON

BACK ENTER

ProMinent®

ALARM

ENT

Pool 750.0mV

7.40pH 85.0F

Alarm Information

Clear (Reset) All Alarms

Changing a Pump/Feeder

Auto to Off - Manual ON

Relays 1 and 3 are factory set as Acid Pump and Oxidant

Pump, using pH Sensor C, and ORP Sensor D, respectively.

They are default in the AUTO mode for ON/OFF control to 7.4

pH and 750mV. They can be set to the on mode for priming or

to the OFF mode to temporarily disable chemical feed.

If the orange ALARM light is ashing, an alarm has activated.

1. Choose the relay you

want to change by

pressing the button

until the selected

(relay 1 or 3) is

shown.

1. Press once to

view active alarms.

The LCD screen will

alternately show the

oxidant feeder status

along with any inputs

(letter) or outputs

(numbers) that have

alarmed.

Note: Alarms may have

been corrected and the

alarm just may need to

be acknowledged.

2. Press and hold the

button and the display

will change to show

⏎AUTO ↓OFF ↑ON

while the button is

held down.

1. When the alarm light

is ashing and you

just want to

acknowlege and clear

the alarms, press

then twice.

[Alarm Status Screen]

[Alarm Menus]

[Clear Alarms]

3. While holding the

button, pressing one

of the three other

buttons , or

will put the output in

that respective mode.

DCM 5 Series Controller

Quick Start Guide

The default timeout for the forced ON condition is 10 minutes.

After that delay, the relay will revert to AUTO mode. To adjust

this time, refer to the install manual or ask your ProMinent

Distributor for assistance.

ProMinent Fluid Controls, Inc.

136 Industry Drive • Pittsburgh, Pa 15275

Ph: 412-787-2484 • Fx: 412-787-0704

eMail: [email protected]

www.prominent.us

Autres manuels ProMinent Contrôleurs

ProMinent

ProMinent DULCOMETER Manuel utilisateur

ProMinent

ProMinent DULCOMETER D2C Manuel utilisateur

ProMinent

ProMinent DCM 2 Series Manuel utilisateur

ProMinent

ProMinent DULCOMETER D1CA Manuel utilisateur

ProMinent

ProMinent Aegis-II Manuel utilisateur

ProMinent

ProMinent DULCOMETER D1C Manuel utilisateur

ProMinent

ProMinent multiFLEX M10 Manuel utilisateur

ProMinent

ProMinent DULCOMARIN II Schéma de câblage

ProMinent

ProMinent DULCOMETER Manuel utilisateur

ProMinent

ProMinent DULCOMETER PH-501 Manuel utilisateur

ProMinent

ProMinent diaLog DACb Schéma de câblage

ProMinent

ProMinent Splash Control Pro 2 Manuel utilisateur

ProMinent

ProMinent DULCOMETER D1C Manuel utilisateur

ProMinent

ProMinent Aegis-II Manuel utilisateur

ProMinent

ProMinent DULCOMETER diaLog DACb Guide de planification

ProMinent

ProMinent DCM510 Manuel utilisateur

ProMinent

ProMinent Splash Control 2 Manuel utilisateur

ProMinent

ProMinent DULCOMETER D2C Manuel utilisateur

ProMinent

ProMinent DULCOMETER Aegis-II Manuel utilisateur

ProMinent

ProMinent DULCOMETER D1Cb Manuel de l'opérateur

ProMinent

ProMinent DCM3 Series Manuel utilisateur

ProMinent

ProMinent DULCOMETER Compact Manuel utilisateur

ProMinent

ProMinent DULCOMETER D1CA Manuel utilisateur

ProMinent

ProMinent DULCOMETER D2C Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur