PROAIM Curve-120 Manuel utilisateur
1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Assembly Manual
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Curve-120 Curved Camera Slider with Moon
Control System (SL-CUR-120-MC)
Camera Slider
2 x End Feet and
1 x Centre feet
1/4”Camera Bolt
2 x Knob
Camera Plate
Bag & Strap
1 x Allen key-3/16”
Plasc screw driver
Combo-1
2
Curved Camera slider with End feet Setup
• Loosen the knobs of the end feet and open
them.
• Aer opening the feet, secure them by
re-ghtening with the provided knobs. Follow
the same process for all the sets of feet.
NOTE: Aach the center feet to the center part
of the slider only.
• Remove all the bolts of the Camera Slider from
both the sides with the help of an Allen Key, as
shown in the image.
• Remove the center bolts of the camera slider
with the help of an Allen key.
Camera Plate
with Motor
12v adapter
3 x Allen key
(3/16”, 2.5mm,1.5mm)
Grub screw
Universal
Adapter
1/4” Camera Bolt, BS-100
Remote Controller
+ Strap
3mtr Wire
Stopper
Combo-2
3
• Place the middle feet at the center of the
slider and then insert bolts, by matching the
threads of the slider and the middle feet. Then
ghten with an Allen key to secure.
• Follow the same process to aach the other
set of end feet.
• Insert the stopper, by matching the threads of
the end feet and ghten properly.
• Finally all the feet have been aached to the
slider.
• Follow the same process to insert the other
stopper in the 2nd set of end feet .
NOTE: All sets of feet have threads for stoppers
except for the center feet. The two end feet
stoppers provide support to the camera plate.
• Place the end feet on the slider and then
insert bolts, by matching the threads of the
slider and the feet. Then ghten with an Allen
key to secure.
4
• Loosen the side knobs of the camera plate and
aach it on the slider. Then, re-ghten the
side knobs.
Proaim Curve-120 curved camera slider with Moon Control System.
• Properly insert the camera bolt into the
camera plate.
• Another addional stopper is included to
secure the camera (Not Included) properly.
5
• Open the motor lever by pulling it, as shown in
the image.
• Then secure it with the help of a screwdriver,
as shown in the image.
• Aach the Camera Plate with Motor to the
boom of the camera (Not Included).
• Aach the camera plate by aligning its threads
to the camera and then secure it using the
screw driver (Not Included) .
• Then place the camera (Not Included) on the
slider & properly ghten the knob of the
camera plate.
• The camera (Not Included) is now properly
mounted on the slider, as shown in the
picture.
Camera Plate with Motor
6
• Aach the other end of the 3 meter wire
(4 pin hero push pull connector) to the 4 pin
male connector on controller.
• Aach one end of the 12v adapter cable to the
adapter.
• Then connect the other end of the cable with
the baery.
• Then place the camera (Not Included) on the
slider & properly ghten the knob of the
camera plate.
• Then aach the motor by connecng it
properly to the slider. Thus, powering the
slider.
Cauon: While performing this step, make sure
that your camera plate is mounted onto the
slider.
• Aach the Female connector of the motor to
one end of the 3 meter wire of DC male
connector.
Power the Remote Controller with 2 ways
1. 12v Adapter
7
Remote Controlled Movement Funcons
• Connect the electric plug of the 12v adapter
wire to the universal adapter for generang
the power-supply.
• 12v Adapter: Aach the 12v Adapter with
the controller and press the power buon.
• Baery: Aach the baery (Not Included) with
the controller and press the power buon.
2. Baery
8
YOUR PROAIM CURVE-120 CURVED CAMERA SLIDER WITH
MOTION CONTROL SYSTEM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels PROAIM Accessoires vidéo professionnels
PROAIM
PROAIM P-W5P24-BASE Manuel utilisateur
PROAIM
PROAIM CINEMA Series Manuel utilisateur
PROAIM
PROAIM JB-VG12-01 Manuel utilisateur
PROAIM
PROAIM Low Ninja Baby TP-LNJB-01 Manuel utilisateur
PROAIM
PROAIM CAMTREE HUNT Manuel utilisateur
PROAIM
PROAIM P-WV-2 Manuel utilisateur
PROAIM
PROAIM JB-VG04-01 Manuel utilisateur
PROAIM
PROAIM Spark P-SPK-13 Manuel utilisateur
PROAIM
PROAIM CINEMA P-W5R-GRND Manuel utilisateur
PROAIM
PROAIM CINEMA Series Manuel utilisateur
PROAIM
PROAIM JB-VG08-01 Manuel utilisateur
PROAIM
PROAIM SnapRig UTH-02 Manuel utilisateur
PROAIM
PROAIM P-WV-2PP Manuel utilisateur
PROAIM
PROAIM P-RVMT-01 Manuel utilisateur
PROAIM
PROAIM TP-ULTM-01 Manuel utilisateur
PROAIM
PROAIM SJ-FRMX-04 Manuel utilisateur
PROAIM
PROAIM P-OHCP-01 Manuel utilisateur
PROAIM
PROAIM SD-FUSN-00 Manuel utilisateur
PROAIM
PROAIM P-TRK-FLX Manuel utilisateur
PROAIM
PROAIM WKST-UPL-01 Manuel utilisateur
