Pro-Ject Audio Systems VC-S2 ALU Manuel utilisateur

INSTRUCTIONS FOR USE

Pro-Ject VC-S2 ALU

Controls, features and connections

1 Vacuum arm* (adhesive velvet strips attached)

2 Clamp* (base plate)

3 Fixing screw for base part of clamp*

4 Sidepanel cover with ventilation outlet grille and drain hole

5 Main switch with mains power cord socket

6 Vacuum on/off switch

7 Motor on/off direction switch

8 Vinyl record (not included)

9 Screwable clamp - top plate* with self-adhesive record label seal*

with rubber for sealing record label

10 Hexagon screw for motor flange height adjustment (see page 6)

11 Spindle with motor flange

12 Vacuum arm flange

13 Self-adhesive record label seal*

Accessories (included, but not shown above)

1 Wash it vinyl cleaning concentrate (100ml bottle, mixing ratio 1:10 - 1:20)*

2 Goat hair brush*

3 Replacement adhesive strips for vacuum arm*

4 AC power cord*

5 Drain insert (spout)*

Optional accessories (available on request)

➢Wash it cleaning concentrate, mixing ratio 1:10 - 1:20

bottle sizes: 100ml/250ml/500ml/1l (100ml ≙135 records / both sides, this average

quantity depends on dilution ratio and the amount of ready-to-use cleaning fluid used per

application)

➢Goat hair brush

➢Adhesive strips for vacuum arm

Dear music lover,

Thank you for purchasing a Pro-Ject Audio Systems record cleaning machine.

In order to achieve maximum performance and reliability, please study these instructions carefully.

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

During assembly and adjustment small parts can be easily lost if they are not carefully placed in a suitable

receptacle. Before beginning assembly, please familiarize yourself with the parts listed above which are

correspondingly numbered in the technical diagram. Separately packed items are marked with an asterisk*.

Safety instructions

This appliance is not to be used by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction.

AC outlet voltages vary from country to country. Before connecting to your wall outlet, make sure that

the voltage in your area meets the voltage requirements printed on the device.

Hold the end of the plug when unplugging the power cord. Never handle the power cord while your

hands are wet or damp.

Never place any open flame sources, like burning candles, on or near the device. Do not operate in

damp or wet locations, such as near to a bathtub, sink, swimming pool or any other similar locations.

Keep plastic bags away from children to prevent any risk of suffocation.

Do not cover any ventilation holes (one is located on the left side and others are on bottom).

During operation this unit will generate loud noises, so we recommend the use of hearing protectors

during longer cleaning sessions. Check the unit after transportation for signs of damage, if a damage

is found, do not operate the unit and contact your dealer!

The unit is capable of long time running however in such case platter spindle may get hot and whole

platter/clamp area as well as air coming out from the unit may get warm. The temperature of the

platter can´t damage vinyl records. In order to keep the temperature as low as possible do not

expose the unit to direct sunlight.

Motor should not be turned on when not cleaning your records. Extended running time outside of the

guideline process can cause over-heating.

Setting up the unit

The unit is supplied assembled with the exception of the platter and vacuum arm which are packed

separately. Remove all parts from the transport packaging carefully. Please see the diagram above for

assembly instructions. Base part of the clamp (2) should be attached by using the screw (3), a Phillips

head screwdriver is required but not included. Then apply the self-adhesive label seal (13) on top.

This product is only for non-commercial use.

Using the unit

Please ensure that all assembly and set up steps have been followed as outlined in this manual. All

3 rocker switches ("main switch", "motor" and "vacuum" should be in position "0"). Connect the

power cord to the socket on the rear side of VC-S2 and turn the main switch to the "I" position.

Place a record on the bottom plate. Using moderate force, thread the top clamp plate on the

threaded tip of the centre spindle. Do not over-tighten. If the top plate and screw clamp are too

loose, the record will not turn even if the motor is running.

While the record is turning apply a generous amount of ready-to-use cleaning fluid (6 - 8ml) to the

record while holding the brush horizontally and gently pressing against the record, spread the fluid

across the surface of the record. Use only the necessary amount of fluid (6 –8ml), enough to cover

the record, not the machine!

Do not apply Wash it in less than a 1:10 mix of fluid and water directly to the record! Do not use

cleaning fluids from other suppliers. Use only so little fluid that it is not regularly getting on the surface

of the machine. If this happens remove the excess fluid with a tissue.

Cleaning efficiency can be significantly improved by applying appropriate force on the cleaning brush.

Even more cleaning improvement can be achieved by using warmed-up Wash It cleaning fluid. Wash It

can be warmed in a microwave oven up to 40 degrees Celsius, please check temperature to avoid

record damage. Dilution ratio of warmed-up Wash it should be 1:20. Wash It is non-flammable and

non-toxic. Please note that you are doing all this at your own risk.

The motor can turn both directions or can be stopped during the application of the fluid,

depending on your personal preference. To change direction, choose the "I" position for clockwise

rotation or to the “II” position for counter-clockwise rotation.

It is recommended that you use the brush to clean the record in both directions before vacuuming.

For better dissolving of impurities, wait a few seconds (longer in the case of heavily soiled records)

before starting the vacuuming process.

Once the record has been thoroughly cleaned in both directions, place the vacuum arm above the

record pointing at the spindle until it reaches its lock position.Turn the Vacuum motor to the “I”

position. After the cleaning fluid has been thoroughly vacuumed, switch off the vacuum, followed

by the motor. Return the vacuum arm into its rest position and wait a few seconds for the record to

dry thoroughly. Unscrew the top clamp plate, turn the record over and repeat steps for the opposite

side of the record.

The VC-S2 ALU is equipped with automatic overheating protection, which switches the motor

off in case of excessive usage. After a cool-down period, the VC-S2 ALU will return to its fully

operational status.

Preparation of Wash it concentrate to get ready-to-use cleaning fluid

The cleaning concentrate is usable for vinyl and shellac records and should be diluted before

application:

Mix 1 part of Wash it concentrate with 10-20 parts of distilled / demineralized water!1:10

is better for old and dirty records. For common cleaning or cleaning with warmed-up cleaning

fluid a dilution ratio of 1:20 is sufficient.

Maintenance and cleaning

Your record cleaning machine requires little to no regular maintenance.

A water level gauge is located on the left side of the unit, below the air outlet hole. The internal

tank has a substantial capacity and subsequently takes a very long time to reach full capacity.

Common home use of the unit DOES NOT require to empty the tank. The tank is there to catch

the drained cleaning liquid, and the large surface on the inside and oversized capacity allows the

drained liquid to evaporate faster than in a much smaller tank. In rare cases when the water level

reaches the point marked " ←MAX", the tank should be emptied:

1. Disconnect the mains cable

2. Remove ventilation outlet grille (4)

3. Place the drain insert spout into the hole (drain insert is included in the accessories) and

make sure it sits there tightly, so no fluid can reach the inside of the device.

4. Lift the opposite side of the VC-S2 ALU up to drain the unit reservoir to a big container.

5. Remove the spout and attach the ventilation outlet grille back to its place.

Regularly check the velvet strips on the arm. Make sure they are clean, no dirt or debris is present.

Prior to maintenance, always disconnect the record cleaning machine from the power outlet!

Technical specifications Vinyl Cleaner VC-S2 ALU

Nominal speed

30 r.p.m.

Power consumption

230V/800W, 120V/650W

Dimensions (W x D x H)

415 x 325 x 272 mm (fully assembled)

Weight

8kg (netto)

Fuse

T6,3A

Potential incorrect use and fault conditions

Pro-Ject products are manufactured to the highest standards and undergo strict quality controls

before leaving the factory. Faults that may possibly occur are not necessarily due to material or

production faults but can sometimes be caused by incorrect use. Some of these faults are as follows:

The platter doesn't turn although the unit is switched on:

•The power cord is not connected to the unit.

•The power cord is not plugged in to the AC wall outlet.

•Broken fuse in the main switch.

•Overheating protection is active.

•Top clamp plate is not tightened properly.

How to adjust the height of VC-S2 ALUs record clamp

The VC-S2 ALU is pre-adjusted to spec for standard 80 –180 g records. There is enough headroom,

so that the arm is optimally pressed against the record and the cleaning fluid can be completely

removed. The vacuum arm works best when it is parallel to the record when operating and the adhesive

strips is pressed gently on the surface of record. If the vacuum suction arm is not in the correct distance

from the record it may not be able to completely vacuum the cleaning fluid. In this case it may be

necessary to adjust the height of the clamp. You will need a Phillips screwdriver (to unscrew the set

screw of the clamp base part) and a 2.5mm hexagon key (to loosen motor spindle):

1. Disassemble the clamp (2) by unscrewing the set screw (3) from the motor flange spindle (11)

2. Insert the 2.5mm hexagon key into the hole on the side of motor flange (11)

3. Loosen the hexagon screw, until the flange can be moved up or down

4. When the correct height position is found, fasten the hexagon screw and mount the clamp (2)

You do not need to fully disassemble the flange from the motor!

Service

Should you encounter a problem which the above information does not able to alleviate or identify, please

contact your dealer for assistance.

Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend

keeping the original packaging.

Never return a record cleaning machine without making sure that is it safely disassembled and correctly

packaged in the original packaging.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or change to any part of

the product by unauthorized persons will void the manufacturer’s warranty. Most Pro-Ject products –

unless expressly advertised otherwise –are intended for domestic use only. Using them for business

applications are done so at your own risk.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of printing. The

manufacturer reserves the right to make changes to

the technical specification without prior notice as

deemed necessary to uphold the ongoing process of

technical development.

Declaration of Conformity

We, declare under our responsibility that the product is in conformity with the provisions of Directives:

2014/35/EU including amendments

2014/30/EU including amendments

The following harmonised standards were applied:

EN 60335-1:02+A1:04+A11:04+A2:06+A12:06+A13:08+A14:10+A15:11

EN 60335-2-2:10+A11:12+A1:13

EN 55014-1:06+A1:09+A2:11

EN61000-3-2:14

EN61000-3-3:13

EN55014-2:97+A1:01+A2:08

Pro-Ject Audio Systems a division of Audio Tuning GmbH

1050 Vienna, Austria, Margaretenstrasse 98

[email protected]

Table des matières

Autres manuels Pro-Ject Audio Systems Platine

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtensions 9 S-Shape Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Align it DS3 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems A2 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems X2 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 9.1 Acryl Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential III RecordMaster Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Primary E Phono Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box E Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut III/Phono USB Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 10 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems X1 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems ESSENTIAL III Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Mode d'emploi

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 2 Xperience Basic + Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 1.3 Genie Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 6.1 SB SuperPack Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 6 PerspeX Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 10.1 Evolution Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 SuperPack 1 Manuel utilisateur

Manuels Platine populaires d'autres marques

Gemini

Gemini CDT-05 MKII Manuel utilisateur

Rotel

Rotel RP-820 Manuel utilisateur

Shuman

Shuman MC-250BT Manuel utilisateur

Stanton

Stanton STR8-150 Manuel utilisateur

Audio Technica

Audio Technica AT-LPW40WN Manuel utilisateur

Crosley

Crosley McQueen CR7011-GY Manuel utilisateur

Reloop

Reloop SMP-1 Manuel utilisateur

auna

auna TT-Classic Plus Manuel utilisateur

COMO AUDIO

COMO AUDIO Turntable Analog Manuel utilisateur

Dual

Dual 1009 F Manuel utilisateur

REED

REED Muse3C Manuel utilisateur

AXIOMTEK

AXIOMTEK OPS883-H Series Manuel utilisateur

Pioneer

Pioneer PL-71 Manuel utilisateur

Vestax

Vestax PDX-a1 Manuel utilisateur

Denon

Denon DP-400 Manuel utilisateur

Dual

Dual 504 Manuel utilisateur

Audio-Techica

Audio-Techica AT-LP60XBT Manuel utilisateur

Goldring

Goldring G99 Manuel utilisateur