Pro-Ject Audio Systems Stereo Box Manuel utilisateur

INSTRUCTIONS FOR USE

Pro-Ject Stereo Box

Dear music lover,

thank you for purchasing a PRO-JECT AUDIO amplifier.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

Connectors

Trigger Switch

Make all connections whilst the amplifier is disconnected from the power supply.

Take care to connect the left and right channels correctly. The right channel is usually marked red,

the left channel black or white.

The red speaker terminals carry the positive signal (+), the black speaker terminals the negative

signal (–). Make sure the polarity of the connection is correct at each end of the cables.

Inputs

Line level sources such as CD player radio or TV can be connected to the input sockets marked In 1 & In 2.

Connection to the speakers

The output terminals accept loudspeaker cables terminated with 4mm ∅Banana plugs, spades connectors

or naked wire.

Only connect one loudspeaker with an impedance not less than 4 Ohm per channel.

Remote switching

Optional Pro-Ject Switch Box. The Trigger Switch socket connects the input expander Pro-Ject Switch Box.

The Switch Box provides four extra line-level inputs.

A 30cm remote switching cable is supplied with the Pro-Ject Switch Box for connecting the Trigger Switch

socket of the Pro-Ject Stereo Box.

Do not use this socket for any other connections for which it is not designed.

Mains power connection

The unit is supplied with a power supply suitable for your country's mains supply. Check the label before

connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the

power supply to the Power 20V socket before connecting the power supply to the mains.

Using the Pro-Ject Stereo Box

Stereo Box

Power

Volume

Input

Select

Stand-By

The switch marked Power (press and hold to switch into standby mode) on the front panel and ON/OFF

button on the remote control turn the unit on or back into standby. The blue LED on the front panel shows that

the unit is powered on.

Input selector

After the unit is powered on, pressing the Power button selects the In 1 and In 2 inputs in turn. Select the

inputs using the remote control buttons marked CH- or CH+. If Input 1is selected, the LED over the Input

Select button lights up green. If Input 2 is selected, it lights up red.

If the optional input expander Pro-Ject Switch Box is connected, Input Select will also select the additional

inputs provided by the Switch Box.

Volume

Adjust the volume to the desired level using the large knob marked Volume on the front panel or by using

the buttons on the remote control marked VOL- or VOL+.

Remote control Pro-Ject Stereo Box

ON/OFF switches the unit into and back out of the standby mode

VOL- and VOL+ adjusts the sound volume

CH- and CH+ selects the inputs

CH+

CH-

VOL+

VOL-

ON/OFF

Changing batteries

Proceed as follows:

• Slide open the battery case cover

• Replace the battery. Make sure the battery is the right way round

• Refit the battery case cover

Battery type: 1 x CR 2032 / 3V

Do not dispose the batteries as ordinary domestic refuse. Please dispose your exhausted batteries at

the appropriate collection sites - usually located at supermarkets and drugstores.

Technical specifications Pro-Ject Stereo Box

Power output: 2 x 20W/30W at 8ohms/4ohms (both channels driven)

Frequency response: 20Hz - 20kHz (+ - 0,2 dB)

Channel separation: > 40dB at 20kHz

Noise floor: > -100dB (A weighted)

THD: < 0,05% at 10W

Gain: 22dB

Line-level inputs: 2 pairs RCA/Phono sockets

Input impedance: 20kohms

Trigger Switch: 2-pole 2,5mm co-axial jack

Speaker connectors: 4mm ∅banana plugs, spades connectors or naked wire

Outboard power supply: 20V/3A DC (peak 7A DC), suitable for your country's mains supply

Power consumption: 20V/3A DC

Replacement battery remote control: 1 x CR 2032 / 3V

Dimensions (W x H x D): 103 x 38 x 141mm

Weight: 720g without power supply

Service

Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for

further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible

distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or change to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

PRO-JECT is a Registered Trademark of H. Lichtenegger.

This guide was produced by: Audio Trade GmbH

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pro-Ject Audio Systems Amplificateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box Design Pre Box RS2 Digital Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box SE Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box Design Pre Box DS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems A/D Phono Box S Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems DAC Box TV Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box S Phono Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box DS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box RS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box-Design MaiA S3 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box RS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box S USB Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB V Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box S Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Phono Box S Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur