Pro-Ject Audio Systems Pre Box DS2 Analogue Manuel utilisateur

INSTRUCTIONS FOR USE

Pro-Ject Pre Box DS2 Analogue

Dear music lover,

thank you for purchasing this Pro-Ject Audio preamplifier.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the power supply.

The power supply is used to connect or disconnect the unit from the mains. Make sure that the power

supply is easily accessible at all times. Never handle the device, the power supply while your hands are

wet or damp.

Avoid letting liquids enter the device or the power supply. Never place any item containing liquid, such

as a flower vase on or near the device. Never spill any liquid on the device or the power supply. Never

place any naked flame sources, such as lighted candles on or near the device. The product shall not be used

in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.

Connectors

Make all connections whilst the preamplifier is disconnected from the power supply.

Take care to connect the left and right channels correctly. The right channel is usually marked red,

the left channel black or white.

Never use any other power supply than the one supplied with the unit.

Fix Output

Fix Output connects an analogue record device or a headphone amplifier like a Pro-Ject Head Box.

Var Output

A power amplifier or active loudspeakers can be connected to the output sockets marked Var Output.

Subwoofer output

An active subwoofer may be connected to the output sockets marked Sub Out.

Inputs

The unit has 5 line level RCA inputs marked In1- In 5.

Mains power connection and methods to switch the unit on and off

Connect the low voltage plug from the power supply to the Power 18V socket of the preamplifier before

connecting the power supply to the mains. The unit can be switched on and off by using 2 different methods

which are equal in priorities.

1. Using front pushbutton to switch on or into standby

The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode. The

blue LED on the front panel shows that the unit is powered on. If a trigger signal is present the unit can’t be

switched off by the pushbutton.

2. Remote power on - triggers

The unit can be switched on via other Box Design components when a 12V trigger voltage is present at the

2.5mm socket marked Trigger Input. Special power-on cables (polarity ) in diverse lengths are available

as accessories. The remote power-on signal can be relayed to further units via the Trigger Output socket. When

the 12V trigger signal is switched off, the unit will also switch off.

Trigger cables may only be plugged into the sockets when the unit is disconnected from the power

supply and from the mains. Failure to do so may result in damage of the unit.

Remote control

POWER turns the unit on or back into standby

MUTE has no function on Pre Box DS2 Analogue

CH+/CH- select the inputs in turn

1-5 access to a specific input directly

Front panel controls

Input selector

After the unit is powered on, pressing the buttons◄ and ►next to the LEDs inputs indicators select desired

input.

Volume

Adjust the volume to the desired level, using the large knob on the front panel.

Gain switch

The button +6dB increase gain by 6dB when pressed.

Replacing batteries

Proceed as follows:

•Unlock and slide open the battery case cover

•Replace the battery.

Make sure the battery is the right way round !

•Close the battery case cover

Battery type: 1 x CR2032 / 3V or 1 x CR2025 / 3V

Do not dispose the batteries as ordinary domestic refuse. Please dispose your exhausted batteries at

the appropriate collection sites - usually located at supermarkets and drugstores.

Universal-Remote Control-it DS/RS

Control-it DS/RS is optionally available and allows you to comfortably control this and many other Pro-Ject

Box Design products on one remote.

Technical specifications Pro-Ject Pre Box DS2 Analogue

Frequency response: 20Hz - 20kHz (-0,2/-0dB)

Noise floor: -95dB (A weighted)

THD: 0,001%

Gain: 13dB / 19dB (13+6dB) switchable for all inputs

Pre out: 1 pair RCA/phono sockets

Output voltage typically: 1V at 1kHz (2V with +6dB gain)

Fix and subwoofer out: RCA/phono sockets

Line-level inputs: 5 pairs RCA/phono sockets

Input impedance: 10kohms

Trigger: 12V DC switching voltage

Trigger output: 2-pole 2,5mm co-axial jack

Outboard power supply: 18V/500mA DC, suitable for your country's mains supply

Power consumption: 220mA DC

Replacement battery remote control: 1 x CR2032 / 3V or 1 x CR2025 / 3V

Dimensions W x H x D (D with sockets): Aluminium version: 206 x 71 x 220 mm

Wood version: 240 x 72 x 220 mm

Weight: Aluminium version: 1430 g without power supply

Wood version: 1880 g without power supply

Service

Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for

further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible

distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or changes to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Table des matières

Autres manuels Pro-Ject Audio Systems Amplificateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Head Box II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Phono Box S Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Audio Systems Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box SE Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Record Box E Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box MK II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Head Box S Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Record Box USB Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems AMP BOX DS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Analogue Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box SE Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box DS Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box SE Mono Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box SE II Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Digital Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems CD Box Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box MK II Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur