Premier Mounts FPS-300 Manuel utilisateur

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1321 S. State College Blvd., Fullerton, CA 92831 USA

Warranty, Garantie, Garantía, Garanzia, Garantie, Waarborg: http://www.mounts.com/warranty

9535-000-011-0X Rev.2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

FPS-300

53.38

(HOLD DIM)

16.00

16.00 16.00

Display Width

FACTOR

15.250"

Mounting

Distance

Desired

Distance

OPTIONAL POWER BOX

OUTLET LOCATION

OPTIONAL POWER BOX

OUTLET LOCATION

THE FIRST SLOTS MUST

ALWAYS HAVE AN ANCHOR

ON EITHER END IN ANY GIVEN

INSTALLATIONAPPLICATION

ROLLER PLATE

Mounting Distance = Display Width/2 + Desired Distance - 15.25”

WALL STRUCTURE

M8 x 16mm

1/4”

M5 x 10mm M3 x 8mm 1/4” x 3”

M4 x 5mm

#10

#8 x 1-1/4”

x8 x6 x4 x8

x18

x20

x2 x1

1/8” / 3.25mm

(Wood Only)

7/16”

Included components

Required for installation

Note: Prior to installation start, the installer has the option

of concealed power and signal boxes mounted flush on

either the left or right side upper mounting rail end caps. If

power and signal cable are to be run externally to the end

cap, please note provisions have been made to allow for

external “wire mold” channel to be run into the end caps as

well.

Unpack all FPS-300 system components and confirm all

components called out in the supplied parts list are ac-

counted for. With all components laid out select the upper

mounting channel pieces as these will be the first part of the

system to install.

Note: If you are using the optional concealed left or right

side power and signal box sections, install only one side of

the upper track guide along with the power signal box cover

that is opposite of where the power and signal is coming

from. Power and signal cables must run together from either

the left or right side for proper operation of the system.

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

9535-000-011-0X Rev.2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

FPS-300

Depending on the composition of the installation wall, drill

the pilot holes with the proper size drill bit to a depth allow-

ing for full penetration of the mounting screw in the wall to

provide a level and firmly attached upper mounting channel.

Take one 48 in. upper channel section (A) and place it

horizontally on the wall and level at the desired height, in

line with both the predetermined stud locations and with

anchoring position in the far right or left slot. Mark through

the upper channel mounting holes directly on the wall.

Note: Be sure you have clear space behind the dry wall if

you are using the concealed mounting power and signal box

option. For concrete or other solid wall construction, follow

the same process as above, but using suitable hardware for

best installation requirements.

7/16” 1/4”

1/4” x 3”

#8 x 1-1/4”#10

Once the center height is confirmed at 53.38” between the

upper and lower channels, mark and drill pilot holes for the

#10 plastic anchor. Follow the same procedure as step 4

above to install the lower two mounting channel sections,

ensuring the interlocking tabs are together.

Note: Be sure the upper and lower channels are level with

each other and in line at the same starting point as called

out in the instructions.

Once the mounting pilot holes have been drilled, take the

first 48 in. (1219mm) section of mounting channel and se-

cure it level on the wall with the mounting hardware provid-

ed. Once the first upper channel is secure, follow the same

procedure for the second 48 in. (1219mm) upper channel.

Do not overtighten the screws.

A:Make sure the two upper channel sections are locked to-

gether inside the locking tabs provided at the channel ends.

Do NOT tap on the small protruding tabs.

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

9535-000-011-0X Rev.2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

FPS-300

Install the power signal boxes to each end.

Complete all electrical installation at this time.

Note: The upper slider assembly can also be wired using

appropriate wire connection.

With both upper and lower channels level and secure to the

wall, the main slider assembly can be raised (two people

recommended) with the upper rollers properly seated into

the upper channel receiver slots. Once fully seated, the low-

er rollers should be on center with the lower roller channel.

Use UL or VDE listed flexible electrical cord appropriate

for this installation. (Contact your local electrician for more

information).

Push the cord into the plastic guide track, leaving sufficient

length open on either end for full motion of the display on

the slider. Hard wire the cords to universal electrical box.

Repeat for signal cable installation.

Using the spirit level supplied, adjust the stand off of the

lower roller wheels to provide a level vertical for the slider

frame on the wall. Loosen the locking screw at the bottom of

the roller using a Phillips head screwdriver. Install the dome

plug and tighten the bottom lock screw once the slider is

level.

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

9535-000-011-0X Rev.2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

FPS-300

Lay the plastic track glide unit with power and signal cable

installed within track section fully inside the upper channel

receiver section. Dress out the power and signal cable at

each end using the tie wraps supplied to insure smooth full

travel of the slider assembly in both the vertical and horizon-

tal movements of the system.

Note: The orientation of the track will be determined by

where the power box was installed.

Remove the top cover on the slider assembly and set aside

for later re-install.

Power

M5 x 10mm M3 x 8mm

x2 x4

13A

Secure both ends of the cable track system to the upper

channel structure with the track brackets and hardware sup-

plied as shown in the visual diagram.

Secure the power strip to the frame using two (2) M3x8mm

screws and two (2) M3 kep nuts.

Double check all power and signal cables are properly se-

cured to the system channels as to not cause any pinching

of the cables during any movement of the slider system.

M5 x 10mm

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

9535-000-011-0X Rev.2

13B

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

FPS-300

Re-install the upper channel and end covers securely at this

time.

Use additional tie wraps as needed for proper wire and

cable routing.

M4 x 5mm

15B

15A

Install the power signal box covers and channel covers.

Table des matières

Autres manuels Premier Mounts Support TV

Premier Mounts

Premier Mounts CTM-MS4 Manuel utilisateur

Premier Mounts

Premier Mounts GB-VESA42 Manuel utilisateur

Premier Mounts

Premier Mounts CTM-MS2 Manuel utilisateur

Premier Mounts

Premier Mounts PaneLock Manuel utilisateur

Premier Mounts

Premier Mounts Rotary series Manuel utilisateur

Premier Mounts

Premier Mounts Universal Flat Mount FM3 Manuel utilisateur

Premier Mounts

Premier Mounts PCM-MS2 Manuel utilisateur

Premier Mounts

Premier Mounts ECM-3763D Manuel utilisateur

Premier Mounts

Premier Mounts CTM-MS1 Manuel utilisateur

Premier Mounts

Premier Mounts PSM-402T Manuel utilisateur

Premier Mounts

Premier Mounts PCB-CSL1 Manuel utilisateur

Premier Mounts

Premier Mounts LIFT1 Manuel utilisateur

Premier Mounts

Premier Mounts P4263T Manuel utilisateur

Premier Mounts

Premier Mounts GearBox GB-MS2 Manuel utilisateur

Premier Mounts

Premier Mounts RFM Manuel utilisateur

Premier Mounts

Premier Mounts AM250 Manuel utilisateur

Premier Mounts

Premier Mounts Rotary series Manuel utilisateur

Premier Mounts

Premier Mounts TWM-103 Manuel utilisateur

Premier Mounts

Premier Mounts WMK-027 Manuel utilisateur

Premier Mounts

Premier Mounts AM175 Manuel utilisateur

Premier Mounts

Premier Mounts FTP-096 Manuel utilisateur

Premier Mounts

Premier Mounts CTM-MS1 Manuel utilisateur

Premier Mounts

Premier Mounts RTM-S Manuel utilisateur

Premier Mounts

Premier Mounts LMVS Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur