PRECISION DIGITAL Pd6300 Manuel utilisateur

PRECISION DIGITAL CORPORATION

233 South Street • Hopkinton MA 01748 USA

Tel (800) 343-1001 • Fax (508) 655-8990

www.predig.com

PD6300 Pulse Input Rate/Totalizer

Instruction Manual

•Pulse, Open Collector, NPN, PNP, TTL, Switch Contact,

Sine Wave (Coil), Square Wave Inputs

•Gate Function for Rate Display of Slow Pulse Rates

•NEMA 4X, IP65 Front

•Universal 85-265 VAC, or 12/24 VDC Input Power Models

•Large Dual-Line 6-Digit Display, 0.60" & 0.46"

•Isolated 24 VDC Transmitter Power Supply

•Programmable Displays & Function Keys

•Sunlight Readable Display Models

•Rate Displayed as Units per Second, Minute, Hour, or Day

•Total, Grand Total or Non-Resettable Grand Total

•9-Digit Totalizer with Total Overflow Feature

•K-Factor Calibration or Scale with up to 32-Point Linearization

•2 or 4 Relays + Isolated 4-20 mA Output for Rate/Total/Grand Total

•External 4-Relays & Digital I/O Expansion Modules

•USB, RS-232 & RS-485 Serial Communication Options

•Modbus

RTU Communication Protocol Standard

•Configure, Monitor, and Datalog from a PC with

Free MeterView

Pro Software

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Disclaimer

The information contained in this document is subject to change

without notice. Precision Digital makes no representations or

warranties with respect to the contents hereof; and specifically

disclaims any implied warranties of merchantability or fitness for a

particular purpose.

CAUTION: Read complete

instructions prior to

installation and operation

of the meter.

WARNING: Risk of

electric shock or

personal injury.

Limited Warranty

Precision Digital Corporation warrants this product against defects in

material or workmanship for the specified period under

“Specifications” from the date of shipment from the factory. Precision

Digital’s liability under this limited warranty shall not exceed the

purchase value, repair, or replacement of the defective unit.

Registered Trademarks

PROVU®and MeterView®Pro are registered trademarks of Precision

Digital Corporation. All other trademarks mentioned in this document are

the property of their respective owners.

www.predig.com

WARNING:

This product is not recommended for life support applications

or applications where malfunctioning could result in personal

injury or property loss. Anyone using this product for such

applications does so at his/her own risk. Precision Digital

Corporation shall not be held liable for damages resulting from

such improper use.

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Table of Contents

INTRODUCTION ------------------------------------------------------------ 6

ORDERING INFORMATION --------------------------------------------- 7

SPECIFICATIONS---------------------------------------------------------- 8

General-------------------------------------------------------------------------------8

Rate Input ------------------------------------------------------------------------- 10

Rate/Totalizer -------------------------------------------------------------------- 11

Relays ------------------------------------------------------------------------------ 12

Isolated 4-20 mA Transmitter Output ------------------------------------ 13

Modbus®RTU Serial Communications---------------------------------- 14

PDA1044 Digital Input & Output Expansion Module---------------- 14

COMPLIANCE INFORMATION ----------------------------------------15

Safety ------------------------------------------------------------------------------- 15

Electromagnetic Compatibility--------------------------------------------- 15

SAFETY INFORMATION ------------------------------------------------16

INSTALLATION ------------------------------------------------------------17

Unpacking------------------------------------------------------------------------- 17

Panel Mounting Instructions------------------------------------------------ 17

Configuration for 12 or 24 VDC Power Option------------------------ 19

Transmitter Supply Voltage Selection (P+, P-) ----------------------- 20

Connections---------------------------------------------------------------------- 20

Connectors Labeling--------------------------------------------------------- 21

Power Connections ---------------------------------------------------------- 21

Signal Connections ---------------------------------------------------------- 22

Modbus RTU Serial Communications ----------------------------------- 24

Relay Connections ----------------------------------------------------------- 24

Switching Inductive Loads-------------------------------------------------- 25

F4 Digital Input Connections----------------------------------------------- 26

4-20 mA Output Connections---------------------------------------------- 26

Analog Output Transmitter Power Supply------------------------------ 26

External Relay & Digital I/O Connections ------------------------------ 27

Interlock Relay Feature ----------------------------------------------------- 28

SETUP AND PROGRAMMING ----------------------------------------29

Front Panel Buttons and Status LED Indicators --------------------- 30

Display Functions and Messages----------------------------------------- 31

Main Menu ------------------------------------------------------------------------ 35

Setting Numeric Values ------------------------------------------------------ 36

Setting Up the Rate/Totalizer Meter (setup) --------------------------- 37

Setting the Input Signal (Input) ------------------------------------------ 38

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Setting the Totalizer Features (total) ---------------------------------- 38

Setting the Input Units or Custom Tags (units)---------------------- 39

Setting the Decimal Point (dEc pt) -------------------------------------- 40

Programming the Rate/Totalizer (prog) -------------------------------- 40

K-Factor Calibration (Factor) ----------------------------------------- 41

Multi-Point Calibration & Scaling-------------------------------------- 41

MeterView®Pro Software ----------------------------------------------- 41

Scaling the Meter (SCALE) ---------------------------------------------- 42

Gate Function (Gate) ---------------------------------------------------- 43

Contact De-Bounce Filter (FiLter) ---------------------------------- 44

Time Base, Total Conversion Factor & Total Reset-------------- 45

Calibrating the Meter with External Source (Cal)----------------- 46

Setting the Display Parameter & Intensity (dsplay) ----------------- 47

Display Setup Menu --------------------------------------------------------- 48

Setting the Relay Operation (relay) ------------------------------------- 49

Relay Assignment (Assign) ----------------------------------------------- 50

Setting the Relay Action ---------------------------------------------------- 51

Programming Set and Reset Points ------------------------------------- 52

Setting Fail-Safe Operation ------------------------------------------------ 52

Programming Time Delay -------------------------------------------------- 52

Relay and Alarm Operation Diagrams ----------------------------------- 53

High Alarm Operation (Set > Reset) ------------------------------------- 53

Low Alarm Operation (Set < Reset)-------------------------------------- 54

High Alarm with Fail-Safe Operation (Set > Reset) ------------------ 55

Low Alarm with Fail-Safe Operation (Set < Reset)------------------- 56

Alternation Control Operation --------------------------------------------- 57

Rate Relay Sampling Operation ------------------------------------------ 58

Total Relay Sampling Operation------------------------------------------ 58

Time Delay Operation ------------------------------------------------------- 59

Relay Operation Details ------------------------------------------------------ 60

Overview------------------------------------------------------------------------ 60

Relays Auto Initialization---------------------------------------------------- 60

Fail-Safe Operation ---------------------------------------------------------- 60

Front Panel LEDs------------------------------------------------------------- 61

Latching and Non-Latching Relay Operation -------------------------- 61

Non-Latching Relay (Auto)------------------------------------------------- 62

Non-Latching Relay (A-nman) --------------------------------------------- 62

Latching Relay (LatcH) ----------------------------------------------------- 62

Latching Relay (Lt-Clr)---------------------------------------------------- 63

Acknowledging Relays ------------------------------------------------------ 63

Setting Up the Interlock Relay (Force On) Feature ------------------ 64

Scaling the 4-20 mA Analog Output (Aout) ---------------------------- 65

Reset Menu (reset) ------------------------------------------------------------ 66

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Control Menu (Contrl)-------------------------------------------------------- 66

Setting Up the Password (pass) ------------------------------------------- 66

Protecting or Locking the Meter------------------------------------------- 67

Total Reset Password & Non-Resettable Total ----------------------- 67

Making Changes to a Password Protected Meter-------------------- 68

Disabling Password Protection-------------------------------------------- 68

Advanced Features Menu---------------------------------------------------- 69

Advanced Features Menu & Display Messages ---------------------- 69

Rounding Feature (round) ------------------------------------------------- 72

Modbus RTU Serial Communications (serial) ---------------------- 72

Select Menu (SElEct) ------------------------------------------------------- 73

Signal Input Conditioning (Functn) -------------------------------------- 73

Multi-Point Linearization (Linear)---------------------------------------- 74

Low-Flow Cutoff (CutofF) -------------------------------------------------- 74

Analog Output Programming (AoutPr)---------------------------------- 75

Programmable Function Keys User Menu (user) -------------------- 76

Meter Copy Function (Copy) ----------------------------------------------- 77

METER OPERATION-----------------------------------------------------79

Front Panel Buttons Operation -------------------------------------------- 79

Function Keys Operation ---------------------------------------------------- 79

F4 Operation --------------------------------------------------------------------- 80

Maximum/Minimum Readings---------------------------------------------- 80

TROUBLESHOOTING----------------------------------------------------81

Diagnostics Menu (diag)----------------------------------------------------- 81

Determining Software Version -------------------------------------------- 81

Reset Meter to Factory Defaults ------------------------------------------- 82

Factory Defaults & User Settings----------------------------------------- 83

Troubleshooting Tips --------------------------------------------------------- 86

EU DECLARATION OF CONFORMITY -----------------------------89

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Table of Figures

Figure 1: 1/8 DIN Panel Cutout and Mounting................................... 17

Figure 2: Meter Dimensions - Side View............................................ 18

Figure 3: Meter Dimensions - Top View............................................. 18

Figure 4: Jumper Configuration for 12/24 VDC Power ..................... 19

Figure 5: Transmitter Supply Voltage Selection............................... 20

Figure 6: Connector Labeling for Fully Loaded PD6300 .................. 21

Figure 7: Power Connections............................................................. 21

Figure 8: Flowmeter Powered by Internal Power Supply................. 22

Figure 9: Flowmeter Powered by External Supply ........................... 22

Figure 10: Self-Powered Magnetic Pickup Coil Flowmeter.............. 22

Figure 11: Relay Connections ............................................................ 24

Figure 12: AC and DC Loads Protection ........................................... 25

Figure 13: Low Voltage DC Loads Protection................................... 25

Figure 14. F4 Digital Input Connections ............................................ 26

Figure 15: 4-20 mA Output Connections ........................................... 26

Figure 16: Expansion Modules & DIN Rail Mounting Kit.................. 27

Figure 17: External Relays Module Connections ............................. 27

Figure 18: Digital I/O Module Connections ....................................... 28

Figure 19: Interlock Connections....................................................... 28

Figure 20: Acknowledge Relays w/Function Key or Digital Input ... 63

Figure 21: Meter Copy Connection .................................................... 77

Figure 22: 1/8 DIN Panel Cutout Template ........................................ 88

INTRODUCTION

The PROVU®PD6300 is a multipurpose, easy to use pulse rate/totalizer ideal for

flow rate, total, and control applications. It accepts pulse (40 mVp-p to 8 Vp-p),

square wave (0-5 V, 0-12 V, or 0-24 V), open collector, NPN, PNP, TTL or switch

contact signals. Three of the front panel buttons can be custom-programmed for

specific operation.

The basic model includes an isolated 24 VDC transmitter power supply that can be

used to power the input transmitter or other devices. An additional isolated 24 VDC

power supply is included with the 4-20 mA output option. A digital input is standard.

A fully loaded PD6300 pulse rate/totalizer meter has the following: four SPDT relays,

4-20 mA output, and two 24 VDC power supplies. The PD6300 capabilities may be

enhanced by adding the following external expansion modules: four SPST relays

(creating an eight-relay rate/totalizer), two digital I/O modules with four inputs and four

outputs each, and RS-232, RS-485, and USB communication adapters.

The eight relays can be used for alarm indication or process control applications. The

4-20 mA isolated output, Modbus RTU serial communications, and digital I/O options

make the PD6300 an excellent addition to any system.

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

ORDERING INFORMATION

Standard Models

85-265 VAC

Model

12/24 VDC

Model Options Installed

PD6300-6R0 PD6300-7R0 No options

PD6300-6R2 PD6300-7R2 2 relays (PD1102*)

PD6300-6R3 PD6300-7R3 4-20 mA output (PD1103*)

PD6300-6R4 PD6300-7R4 4 relays (PD1104*)

PD6300-6R5 PD6300-7R5 2 relays & 4-20 mA output (PD1105*)

PD6300-6R7 PD6300-7R7 4 relays & 4-20 mA output (PD1107*)

*Model number for replacement option card.

SunBright Display Models

85-265 VAC

Model

12/24 VDC

Model Options Installed

PD6300-6H0 PD6300-7H0 No options

PD6300-6H2 PD6300-7H2 2 relays (PD1102*)

PD6300-6H3 PD6300-7H3 4-20 mA output (PD1103*)

PD6300-6H4 PD6300-7H4 4 relays (PD1104*)

PD6300-6H5 PD6300-7H5 2 relays & 4-20 mA output (PD1105*)

PD6300-6H7 PD6300-7H7 4 relays & 4-20 mA output (PD1107*)

*Model number for replacement option card.

Accessories

Model Description

PDA1002 DIN-Rail mounting kit for two expansion modules

PDA1004 4 SPST (Form A) relays

PDA1044 4 digital inputs & 4 digital outputs (2 may be connected)

PDA1200 Meter copy cable

PDA1232 RS-232 serial adapter

PDA1485 RS-485 serial adapter

PDA7485-I RS-232 to RS-422/485 isolated converter

PDA8008 USB serial adapter

PDA8232-N USB to RS-232 non-isolated converter

PDA8485-I USB to RS-422/485 isolated converter

PDA2811 1 Meter Plastic NEMA 4X Enclosure

PDA2812 2 Meter Plastic NEMA 4X Enclosure

PDX6901 Suppressor (snubber): 0.01 µF/470 Ω, 250 VAC

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

SPECIFICATIONS

Except where noted all specifications apply to operation at +25°C.

General

DISPLAY Upper display: 0.6" (15 mm) high, red LEDs

Lower display: 0.46" (12 mm) high, red LEDs

6 digits: each (-99999 to 999999), with lead zero blanking.

DISPLAY

INTENSITY

Eight user selectable intensity levels

DISPLAY

UPDATE RATE

Rate: 10 per second; up to 1 per 100 seconds (and is a

function of Low Gate setting)

Total: 10 per second (fixed)

OVERRANGE Display flashes 999999

DISPLAY

ASSIGNMENT

The Upper and Lower displays may be assigned to rate,

total, grand total, alternate rate & total, max/min, units

(lower display only), set points, Modbus input, & more.

PROGRAMMING

METHODS

Four front panel buttons, digital inputs, PC and MeterView Pro

software, Modbus registers, or cloning using Copy function.

RECALIBRATION All ranges are calibrated at the factory to read frequency in

Hz. No recalibration required.

MAX/MIN

DISPLAY

Max/min readings reached by the process are stored until

reset by the user or until power to the meter is cycled.

PASSWORD Three programmable passwords restrict modification of

programmed settings and two prevent resetting the totals.

Pass 1: Allows use of function keys and digital inputs

Pass 2: Allows use of function keys, digital inputs and editing set/reset points

Pass 3: Restricts all programming, function keys, and digital inputs.

Total: Prevents resetting the total manually

Gtotal: Prevents resetting the grand total manually

NON-VOLATILE

MEMORY

All programmed settings are stored in non-volatile memory

for a minimum of ten years if power is lost.

POWER

OPTIONS

85-265 VAC 50/60 Hz, 90-265 VDC, 20 W max

or jumper selectable 12/24 VDC ±10%, 15 W max

FUSE Required external fuse: UL Recognized, 5 A max, slow

blow; up to 6 meters may share one 5 A fuse

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

ISOLATED

TRANSMITTER

POWER SUPPLY

Terminals P+ & P-: 24 VDC ±10%. 12/24 VDC powered models

selectable for 24, 10, or 5 VDC supply (internal jumper J4).

ProVu Series (PD6300):

85-265 VAC models rated @ 200 mA max, 12/24 VDC powered

models rated @ 100 mA max, @ 50 mA max for 5 or 10 VDC

supply.

ProtEX-MAX (PD8 Series):

All models transmitter supply rated @ 25mA max.

ISOLATION 4 kV input/output-to-power line

500 V input-to-output or output-to-P+ supply

OVERVOLTAGE

CATEGORY

Installation Overvoltage Category II:

Local level with smaller transient overvoltages than

Installation Overvoltage Category III.

ENVIRONMENTAL ProVu Series (PD6300):

Operating temperature range: -40 to 65°C

Storage temperature range: -40 to 85°C

Relative humidity: 0 to 90% non-condensing

ProtEX-MAX (PD8 Series):

T6 Class operating temperature range Ta = -40 to 60°C

T5 Class operating temperature range Ta = -40 to 65°C

See LIM8 ProtEX-MAX instruction manual for additional

details.

MAX POWER

DISSIPATION

ProtEX-MAX (PD8 Series): Maximum power dissipation

limited to 15.1 W. See LIM8 ProtEX-MAX instruction

manual for additional details.

CONNECTIONS Removable screw terminal blocks accept 12 to 22 AWG

wire, RJ45 for external relays, digital I/O, and serial

communication adapters.

ENCLOSURE 1/8 DIN, high impact plastic, UL 94V-0, color: black

MOUNTING 1/8 DIN panel cutout required:

3.622" x 1.772" (92 mm x 45 mm)

Two panel mounting bracket assemblies are provided.

TIGHTENING

TORQUE

Screw terminal connectors: 5 lb-in (0.56 Nm)

OVERALL

DIMENSIONS

4.68" x 2.45" x 5.64" (119 mm x 62 mm x 143 mm)

(W x H x D)

WEIGHT 9.5 oz (269 g)

WARRANTY 3 years parts & labor

Model PD6300 Pulse Input Rate/Totalizer Instruction Manual

Rate Input

INPUTS Field selectable: Pulse or square wave 0-5 V, 0-12 V, or

0-24 V @ 30 kHz; TTL; open collector 4.7 kΩpull-up to 5 V

@ 30 kHz; NPN or PNP transistor, switch contact 4.7 kΩ

pull-up to 5 V @ 40 Hz; Modbus PV (Slave)

LOW VOLTAGE

MAG PICKUP

(Isolated)

Sensitivity: 40 mVp-p to 8Vp-p

MINIMUM INPUT

FREQUENCY

0.001 Hz

Minimum frequency is dependent on high gate setting.

MAXIMUM INPUT

FREQUENCY

30,000 Hz (10,000 for low voltage mag pickup)

INPUT

IMPEDANCE

Pulse input: Greater than 300 kΩ@ 1 kHz.

Open collector/switch input: 4.7 kΩpull-up to 5 V.

ACCURACY ±0.03% of calibrated span ±1 count

TEMPERATURE

DRIFT

Rate display is not affected by changes in temperature.

MULTI-POINT

LINEARIZATION

2 to 32 points

LOW-FLOW

CUTOFF

0-999999 (0 disables cutoff function)

DECIMAL POINT Up to five decimal places or none:

d.ddddd, d.dddd, d.ddd, d.dd, d.d,or dddddd

CALIBRATION May be calibrated using K-factor, internal calibration, or by

applying an external calibration signal.

K-FACTOR Field programmable K-factor converts input pulses to rate in

engineering units. May be programmed from 0.00001 to

999,999 pulses/unit.

CALIBRATION

RANGE

Input 1 signal may be set anywhere in the range of the

meter; input 2 signal may be set anywhere above or below

input 1 setting.

Minimum input span between any two inputs is 10 Hz.

An error message will appear if the input 1 and input 2

signals are too close together.

FILTER Programmable contact de-bounce filter: 40 to 999 Hz

maximum input frequency allowed with low speed filter.

TIME BASE Second, minute, hour, or day

GATE Low gate: 0.1-99.9 seconds

High gate: 2.0-999.9 seconds

F4 DIGITAL INPUT

CONTACTS

3.3 VDC on contact. Connect normally open contacts

across F4 to COM.

F4 DIGITAL INPUT

LOGIC LEVELS

Logic High: 3 to 5 VDC

Logic Low: 0 to 1.25 VDC

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PRECISION DIGITAL Instrument de mesure

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6200 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL NOVA PD560 Series Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL vantageview Safe Touch PD6700 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL SABRE T PD743 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD6701 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL ProtEx Pro PD6800-0L1 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD686 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL SABRE T PD743 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader Series Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD6060 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD603 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader Series Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Javelin D PD644 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD6200 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD686 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-7000 Series Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD755 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL ProtEX-RTP PD6830 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD6060 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD677 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL PD660 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6080 Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader PD6620 Series Manuel utilisateur

PRECISION DIGITAL

PRECISION DIGITAL DART PD602 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

PRECISION DIGITAL pd6300 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques