Polycom MGC+100 ReadiConvene Manuel utilisateur

MGC+50/100 Installation

& Configuration Guide

General Safety Precautions

Follow these rules to ensure general safety:

• Keep the area around the Polycom MGC+ unit clean, free of clutter

and well ventilated.

• When lifting the MGC+50/100, two people at either end should lift

slowly with their feet spread out to distribute the weight. Always

keep your back straight and lift with your legs.

• Decide on a suitable location for the equipment rack that will hold

the MGC+ unit and is near a grounded power outlet.

• Ensure that the leveling jacks on the rack’s bottom are fully

extended to the floor with the full rack’s weight resting on them.

• Stabilizers should be attached to a single rack . In multiple rack

installations, the racks should be coupled together. Always make

sure the rack is stable before extending a component from the rack.

• Use a regulating uninterruptable power supply (UPS) to protect the

MGC+ unit from power surges and voltage spikes, and to keep it

operating in case of a power failure.

Preparations

Obtain the following information from your network administrator:

• MGC+ unit, Subnet Mask and Default Gateway IP addresses

• Gatekeeper IP address

• DNS IP address, if applicable

• SIP server IP address, if applicable

8DOC2143A

3Click OK.

A confirmation message is displayed. Click OK.

Conferencing Entities

The MGC+ unit is shipped with two Entry Queues and eight Meeting

Rooms. Different Entry Queues and Meeting Rooms are created

according to conference line rate and video session type. The Entry

Queues and Meeting Rooms are set to line rate of 384 Kbps.

• Entry Queue CP whose Numeric ID is 1111, and Video Session type

is Continuous Presence, is used to access Meeting Rooms 1000,

2000, 3000 and 4000.

•EntryQueueVSW whose Numeric ID is 2222, and Video Session

type is Video Switching, is used to access Meeting Rooms 5000,

6000, 7000 and 8000.

Meeting Room names and Numeric IDs are identical. For example,

Meeting Room 3000 has the Numeric ID 3000.

Meeting Rooms 1000, 2000, 3000 and 4000 are set to Continuos Presence

mode. Meeting Rooms 5000, 6000, 7000 and 8000 are set to Video

Switching mode.

SIP Select this check box to indicate that SIP participants can

connect to the MCU using this service. Then select:

•Specify - to manually define the SIP server.

•Auto - to automatically detect the SIP server’s IP

address if a DHCP or if a DNS Server is defined.

SIP Server IP

Address or

Name

If SIP-Specify is selected, and a DHCP is not used, enter

either the IP address of the preferred SIP server or its

host name (if a DNS server is used).

Domain Name

or IP Address Enter the domain name to identify the SIP server in the

domain according to the host part in the dialed string.

Field Description

www.polycom.com

Unpacking and Installing the MGC+50/100

1Place the MGC+ unit on a stable flat surface in the selected location.

2Release the clasp locks at the bottom, and lift the MGC+ package

top cover.

3Lift the MGC+ unit and place it on the required flat surface.

If you are rack mounting the MGC+ unit, allow a minimum

clearance of 3” above the unit.

4To mount the MGC+100 in a 23” rack, place the MCU in the rack

and while supporting it, screw the mounting brackets to the rack

securing it with bolts and self-locking nuts (which you provide).

5To connect to the power source, insert the power cable into the

power connector on the rear panel of the MGC+ unit and insert the

power cable into the power source socket.

6Turn on the power switch.

The connections for the MGC+50 and the MGC+100 are

similar, therefore only the MGC+100 is shown in the figure

above.

AC Inlet

Main Switch

DEBUG

LINE IN

COM2

COM1

KEYBOARD

MOUSE

VGA

LAN

COM2

COM1

KEYBOARD

MOUSE

VGA

LAN

ALARMS

LAN

wor

Default Router If DHCP is not used, enter the IP address of the default

router.

DNS Select this check box to indicate that a DNS server is

used in the network. Then select one of the following:

•Specify - to enter the IP address of the DNS server.

•Auto - to automatically detect the primary DNS IP

address, provided the DNS Server is defined in the

DHCP server and the DHCP - obtain IP Address

automatically check box was selected.

DNS Server IP

Address If DNS–Specify was selected, enter the IP address of the

primary DNS server.

Local Domain

Name Enter the domain name where the MCU is installed, for

example, polycom.com.

H.323 Select this check box to indicate that H.323 participants

can connect to the MCU using this service.

Gatekeeper Select this check box when a gatekeeper is used.

Gatekeeper IP

Address or

Name

Enter either the gatekeeper’s host name (if the DNS

server is used), or IP address.

Prefix Enter a number to be used byH.323 participants to dial to

the MCU as part of the dial-in string.

Enter 789 to use the default Entry Queues and Meeting

Rooms shipped with the MGC+ unit without modifying

their properties.

When PathNavigator is used, this prefix automatically

registers with the gatekeeper. When another gatekeeper

is used, this prefix usually must also be defined in the

gatekeeper.

Field Description

Initial MGC+ Control Unit IP Configuration

The system is shipped with a default IP address: 129.254.4.8. When the

MGC+ is installed for the first time, you must change the default IP

address of the MCU.

1Insert the Compact Flask disk into the Compact Flash adaptor

(supplied with the MGC+ accessory kit).

2Using a text editor application, open the LAN.CFG file stored on the

Compact flash card.

3In the LAN.CFG file, define the MCU IP address, the subnet Mask

and Default gateway parameters as allocated by the network

administrator. Make sure that there are no extra spaces at the end of

each line

4Save the LAN.CFG file.

5Use the Microsoft Unplug or Eject Hardware procedure prior to

removing the Flash disk. Failure to stop the hardware properly, can

result in a corrupt Compact Flash disk.

6Remove the Compact Flash Memory disk from the PC and insert it

into the MGC+ Control Module Compact Flash slot.

7Press the Reset button on the MGC+.

After the automatic default time-out (15 seconds) the MGC+ IP

settings are changed. The Flash Memory LED must be active and

flashing.

8Press the Eject button when the Flash Memory LED no longer

flashes.

9Remove the Compact Flash card from the MGC+ Control Module

compact flash slot

10 Press the Reset button on the MGC+ to reset the MCU.

Do not press the Eject button while the Flash Memory LED is

flashing.

Define or modify the following parameters:

Field Description

IP Service

Name Enter a name using up to 20 characters, or use the default

name (IP Default Service).

Obtain IP

Address

automatically

(DHCP)

Select this check box to use a DHCP server for automatic

assignment and tracking of IP addresses to the

conference devices.

All Spans

Configuration Select this check box to indicate that a LAN span is

connected to all IP+ cards in the MCU.

Cards

Configuration Click this button to display the automatically detected IP+

cards installed on the MCU, listing their slot number, IP

address and Alias (if known).

•When a DHCP server is used and the Obtain IP

Address automatically (DHCP) check box is selected,

the IP address of the card appears as 0.0.0.0.

To change the IP Address of the card and add an Alias,

double click on the card and then change the IP address,

and add the card’s Alias.

Click OK.

Subnet Mask If DHCP is not used, enter the subnet mask of the MCU’s

IP+ card.

Connecting the MCU to the Network

1To connect the MGC+ unit to your site’s network, connect network

cable to the LAN connector on the rear I/O panel of the MGC+

Control Module and to the network.

2To connect an IP card to the IP network, connect the 8-pin RJ-45

connector of the LAN network cable to the LAN RJ-45 jack on the IP

IO panel of each IP card on the rear panel of the MGC+ unit.

Installing the MGC Manager Application

1Insert the software CD into the CD drive.

2On the Start menu, click Run, and then enter D:\SETUP (where D

is the name of the CD drive). Click OK.

The installation wizard opens.

3Follow the on-screen instructions.

Starting the MGC Manager and Defining the

MCU

1On the Start - Programs menu, select MGC Manager ver 7.5.

The MGC Manager main window opens.

Main Menu

Toolbars

Status pane

Monitor pane

Browser pane

2In the Browser pane, right-click the MCUs Network icon, and then

click New MCU.

The Add MCU dialog box opens.

3In the Name box, enter the name of the MCU using a name that

clearly identifies the MCU.

4In the IP Address box, enter the IP Address of the MCU CU using

the IP address that was configured during the Initial IP

Configuration.

5Click OK.

A new icon with the specified MCU name is added to the MCUs

Network in the Browser pane.

Connecting to the MCU

1Double-click the MCU icon.

The Logon dialog box opens.

2Enter your Login Name and Password, and then click OK.

The default Login and Password are both POLYCOM.

Configuring the IP Network Service

The IP Network Service defines the properties of the IP network used

for connecting IP endpoints to the MCU.

To define the default IP Network Service:

The IP Configuration dialog box automatically opens when the system

detects that the default network settings were not modified to your

site’s configuration.

Autres manuels pour MGC+100 ReadiConvene

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Polycom Matériel réseau

Polycom

Polycom V2IU 6400-S Manuel utilisateur

Polycom

Polycom V2IU5300-S Manuel utilisateur

Polycom

Polycom MGC+100 ReadiConvene Mode d’emploi

Polycom

Polycom V2IU 4350 Series Manuel utilisateur

Polycom

Polycom Video Media Center VMC 1000 Manuel utilisateur

Polycom

Polycom Pano Manuel de service

Polycom

Polycom V2IU 4300T Series Manuel utilisateur

Polycom

Polycom V2IU 6400-S Manuel utilisateur

Polycom

Polycom Video Media Center VMC 1000 Manuel utilisateur

Polycom

Polycom RSS 4000 Manuel utilisateur

Polycom

Polycom RealPresence 4000 Manuel de service

Polycom

Polycom Real-Time Media Conferencing Platform RMX... Manuel utilisateur

Polycom

Polycom V2IU 5300-S Manuel utilisateur

Polycom

Polycom TRAPEZE NETWORKS 1725-36060-001 Manuel utilisateur

Polycom

Polycom Video Media Center VMC 1000 Manuel utilisateur

Polycom

Polycom RMX 1500 Fiche technique

Polycom

Polycom SpectraLink 6000 Series Manuel utilisateur

Polycom

Polycom V2IU 4350 Series Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur