Polycom MSR Series Manuel utilisateur

SOLUTION GUIDE | February 2018 | 3725-61579-002A

Polycom® MSR Series

translated into another language or format, or transmitted in any form or by any means, electronic or

mechanical, for any purpose, without the express written permission of Polycom, Inc.

6001 America Center Drive

San Jose, CA 95002

USA

Trademarks Polycom®, the Polycom logo and the names and marks associated with Polycom products

are trademarks and/or service marks of Polycom, Inc. and are registered and/or common law marks in the

United States and various other countries.

All other trademarks are property of their respective owners. No portion hereof may be reproduced or

transmitted in any form or by any means, for any purpose other than the recipient's personal use, without

the express written permission of Polycom.

End User License Agreement By installing, copying, or otherwise using this product, you acknowledge

that you have read, understand and agree to be bound by the terms and conditions of the End User

License Agreement for this product. The EULA for this product is available on the Polycom Support page

for the product.

Patent Information The accompanying product may be protected by one or more U.S. and foreign

patents and/or pending patent applications held by Polycom, Inc.

Open Source Software Used in this Product This product may contain open source software. You may

receive the open source software from Polycom up to three (3) years after the distribution date of the

applicable product or software at a charge not greater than the cost to Polycom of shipping or distributing

the software to you. To receive software information, as well as the open source software code used in

this product, contact Polycom by email at

Disclaimer While Polycom uses reasonable efforts to include accurate and up-to-date information in this

document, Polycom makes no warranties or representations as to its accuracy. Polycom assumes no

liability or responsibility for any typographical or other errors or omissions in the content of this document.

Limitation of Liability Polycom and/or its respective suppliers make no representations about the

suitability of the information contained in this document for any purpose. Information is provided "as is"

without warranty of any kind and is subject to change without notice. The entire risk arising out of its use

remains with the recipient. In no event shall Polycom and/or its respective suppliers be liable for any

direct, consequential, incidental, special, punitive or other damages whatsoever (including without

limitation, damages for loss of business profits, business interruption, or loss of business information),

even if Polycom has been advised of the possibility of such damages.

Customer Feedback We are striving to improve our documentation quality and we appreciate your

feedback. Email your opinions and comments to mailto:[email protected].

Polycom Support Visit the Polycom Support Center for End User License Agreements, software

downloads, product documents, product licenses, troubleshooting tips, service requests, and more.

Contents

Introduction to Polycom MSR Series............................................................... 3

Setting Up Polycom MSR Series.......................................................................4

MSR100 Bundle.................................................................................................................. 4

Set Up the MSR100 Bundle..................................................................................... 4

MSR200 Bundle.................................................................................................................. 5

Set Up the MSR200 Bundle..................................................................................... 5

Verify the Trio System Software Version..................................................................5

Update the Base Profile for the Trio System............................................................ 6

MSR300 Bundle.................................................................................................................. 6

Set Up the MSR300 Bundle..................................................................................... 6

Update the Base Profile for the Trio System............................................................ 7

Verify the Trio System Software Version..................................................................7

Update the Polycom EagleEye IV USB Camera System Software..........................8

Set the Camera Home Position................................................................................8

Move to the Camera Home Position........................................................................ 8

Waking the Polycom EagleEye IV USB Camera System.........................................8

MSR400 Bundle.................................................................................................................. 9

Set Up the MSR400 Bundle..................................................................................... 9

Update the CX5100 System Software Automatically through Control Panel......... 10

Update the CX5100 System Software through USB Drive.....................................10

MSR500 Bundle................................................................................................................ 11

Set Up the MSR500 Bundle with a Single Display................................................. 11

Set Up the MSR500 Bundle with Dual Displays.....................................................11

Update the Base Profile for the Trio System.......................................................... 12

Verify the Trio System Software Version................................................................12

Update the Polycom EagleEye IV USB Camera System Software........................13

Set the Camera Home Position..............................................................................13

Move to the Camera Home Position...................................................................... 13

Waking the Polycom EagleEye IV USB Camera System.......................................13

Upgrading System Software through Windows Update.................................................... 14

Windows Updates on MSR.................................................................................... 14

Troubleshooting............................................................................................... 15

Video Does Not Play......................................................................................................... 15

MSR Dock Does Not Detect the CX5100 System.............................................................15

Polycom, Inc. 1

Known Issues................................................................................................... 17

Contents

Polycom, Inc. 2

Introduction to Polycom MSR Series

Polycom MSR Series delivers a familiar Microsoft Skype for Business experience in small to large

meeting rooms. Polycom MSR Series offers a complete solution that can scale from small huddle rooms

to larger conference rooms. Polycom audio and video peripherals are certified with Skype Room Systems

and support certified Skype Room System docks.

Your infrastructure will likely fall into one of the following configurations:

▪ Skype for Business Online (Office 365) with Exchange Online

▪ Skype for Business Server 2015 on-premises with Exchange Online or Exchange 2013 SP1 on-

premises/Exchange 2016 on-premises

The Polycom MSR Dock does not support Lync Server 2013 or earlier versions. The Polycom MSR Dock

supports 1080p resolution only.

Polycom, Inc. 3

Setting Up Polycom MSR Series

Topics:

▪MSR100 Bundle

▪MSR200 Bundle

▪MSR300 Bundle

▪MSR400 Bundle

▪MSR500 Bundle

▪Upgrading System Software through Windows Update

MSR100 Bundle

The MSR100 bundle includes the Polycom MSR Dock with Microsoft Surface Pro, the Polycom VoxBox,

and Logitech c930e webcam.

Set Up the MSR100 Bundle

Follow the steps below to set up the MSR100 bundle.

Procedure

1. Connect the Logitech c930e webcam USB cable to a USB port on the Polycom MSR Dock.

2. Connect the security USB cable to the Polycom VoxBox using the supplied hardware.

3. Connect a lock, if needed.

4. Connect the other end of the USB cable to the Polycom MSR Dock.

Polycom, Inc. 4

MSR200 Bundle

The MSR200 bundle includes the Polycom MSR Dock with Microsoft Surface Pro, Polycom Trio 8500,

and Logitech c930e webcam.

Note: The Trio 8500 system is supported with software versions 5.5.2 and higher. For more information

on Microsoft Skype Room Systems, refer to Microsoft Technet site.

Set Up the MSR200 Bundle

Follow the steps below to set up the MSR200 bundle.

Note: The Polycom Trio 8500 system must meet the Minimum Setup requirements. For more

information on setting up the Trio 8500 system, refer to the Polycom Support site.

Procedure

1. Connect the power adapter or PoE cable to the Polycom Trio 8500 system.

2. Connect the Micro USB cable to the Micro-B USB port on the Polycom Trio 8500 system.

3. Connect the other end of the USB cable to a USB port on the Polycom MSR Dock.

4. Connect the Logitech c930e webcam USB cable to a USB port on the Polycom MSR Dock.

Verify the Trio System Software Version

You can view the Trio system software version using the local interface, web browser or the Control Panel

application.

Procedure

1. Do one of the following:

Setting Up Polycom MSR Series

Polycom, Inc. 5

▪ On the Trio system, go to Settings > Status > System Information. Enter the IP address of

the Trio system in a web browser and enter the Admin password (the default password is

456).

The software version displays in the Home screen under UC Software Version.

▪ In the Control Panel application software, enter the administrator password and click

System Status.

Update the Base Profile for the Trio System

You can use the Trio system as an audio speakerphone by setting the Base Profile to Skype USB

Optimized.

Polycom recommends connecting the Trio system to the network while updating the base profile.

Procedure

1. Connect a USB cable from the Trio system to the MSR Dock.

2. Do one of the following:

▪ In the Trio system web interface, go to Simple Setup > Base Profile, and select Skype

USB Optimized from the list and click Save.

▪ On the Trio system, go to Setup > Advanced > Administrative Settings > Network

Configurations > Base Profile and select Skype USB Optimized.

MSR300 Bundle

The MSR300 bundle includes the Polycom MSR Dock with Microsoft Surface Pro, Polycom Trio 8800,

and Polycom EagleEye IV USB camera.

Note: The Trio 8800 system is supported with software versions 5.5.3 and higher. The Polycom

EagleEye IV USB camera is supported with software versions 1.1 and higher. For more

information on Microsoft Skype Room Systems, refer to Microsoft Technet site.

Set Up the MSR300 Bundle

Follow the steps below to set up the MSR300 bundle.

Procedure

1. Connect the power adapter or PoE cable to the Polycom Trio 8800 system.

2. Connect the Micro-B USB cable to the Micro-B USB port on the Polycom Trio 8800 system.

3. Connect the other end of the USB cable to a USB port on the Polycom MSR Dock.

4. Connect the USB Type B cable to the USB Type B port on the Polycom EagleEye IV USB camera.

5. Connect the other end of the USB cable to a USB port on the Polycom MSR Dock.

6. Connect the power cable to the Polycom EagleEye IV USB camera.

Setting Up Polycom MSR Series

Polycom, Inc. 6

Update the Base Profile for the Trio System

You can use the Trio system as an audio speakerphone by setting the Base Profile to Skype USB

Optimized.

Polycom recommends connecting the Trio system to the network while updating the base profile.

Procedure

1. Connect a USB cable from the Trio system to the MSR Dock.

2. Do one of the following:

▪ In the Trio system web interface, go to Simple Setup > Base Profile, and select Skype

USB Optimized from the list and click Save.

▪ On the Trio system, go to Setup > Advanced > Administrative Settings > Network

Configurations > Base Profile and select Skype USB Optimized.

Verify the Trio System Software Version

You can view the Trio system software version using the local interface, web browser or the Control Panel

application.

Procedure

1. Do one of the following:

▪ On the Trio system, go to Settings > Status > System Information. Enter the IP address of

the Trio system in a web browser and enter the Admin password (the default password is

456).

The software version displays in the Home screen under UC Software Version.

▪ In the Control Panel application software, enter the administrator password and click

System Status.

Setting Up Polycom MSR Series

Polycom, Inc. 7

Update the Polycom EagleEye IV USB Camera System Software

You can use a USB drive to update the camera system software version. The Polycom EagleEye IV USB

camera system version 1.0.0.388 or later supports Windows Update.

Ensure the following before updating the camera system software:

▪ Use a USB drive with at least 64 MB of available space.

▪ Make sure the file system is in FAT32 format.

Note: Do not remove the USB drive during the software update process.

Procedure

1. Download the latest software image of the camera system from the MSR Series page on the

Polycom support site.

2. Copy the Polycom EagleEye IV USB camera image (polycom-MSRCam-x.x.x-xxx.tar.gz)

into the USB root directory.

3. Plug in the Polycom EagleEye IV USB camera power cable to power on and allow the camera

system to fully boot up.

4. Plug the USB drive into the Polycom EagleEye IV USB camera system.

The Polycom EagleEye IV USB camera system starts the image update and the LED blinks

amber. The Polycom EagleEye IV USB camera system automatically reboots when the image

update is complete. The camera tilts up and then down during the reboot.

5. Remove the USB drive.

Set the Camera Home Position

You may want to set a camera Home position to use as a default.

Procedure

1. Press and hold the Select button for 5 seconds until the LED light blinks green.

Move to the Camera Home Position

You may want to move to a previously set camera Home position.

Procedure

1. To move to camera Home position, press the Select button.

Waking the Polycom EagleEye IV USB Camera System

You can wake the Polycom EagleEye IV USB camera system in the following ways:

▪ Press any button on the remote control.

▪ Send the video content.

▪ Place a call.

Setting Up Polycom MSR Series

Polycom, Inc. 8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Polycom Système de conférence

Polycom

Polycom realpresence trio 8800 Manuel utilisateur

Polycom

Polycom QDX 6000 System Manuel de service

Polycom

Polycom VSX 7000e Series Manuel utilisateur

Polycom

Polycom 5300LF2 VBP-E Series Instructions d'installation

Polycom

Polycom VSX 8000 Series Manuel utilisateur

Polycom

Polycom RealPresence Group 700 system Manuel utilisateur

Polycom

Polycom RealPresence Group 500 systems Instructions d'utilisation

Polycom

Polycom Trio Series Manuel utilisateur

Polycom

Polycom VSX 3000 Manuel de service

Polycom

Polycom DMA 7000 Manuel utilisateur

Polycom

Polycom HDX 9004 Manuel utilisateur

Polycom

Polycom SoundPoint IP 501 SIP 2.2 Manuel utilisateur

Polycom

Polycom RealPresence RMX 4000 Fiche technique

Polycom

Polycom realpresence trio 8800 Manuel utilisateur

Polycom

Polycom CX5000 Guide de référence rapide

Polycom

Polycom VSX 7000s Series Manuel utilisateur

Polycom

Polycom PathNavigator Manuel utilisateur

Polycom

Polycom SoundStation 2W Manuel de service

Polycom

Polycom Polycom EagleEye Producer Manuel utilisateur

Polycom

Polycom Vortex EF2241 Manuel utilisateur

Polycom

Polycom RealPresence Video Protect 500 Manuel

Polycom

Polycom CX5100 Manuel de service

Polycom

Polycom RealPresence Group Series Manuel utilisateur

Polycom

Polycom VSX Series Manuel de service

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur