Plantronics Vista M22 Amplifier Manuel utilisateur
USER GUIDE
Vista M22
Universal Audio Processor
M22 Universal Audio Processor
14
A
B
8
7
9
2
5
13
1
6
12
3
4
15
16
17 18 19 20
1011
1Receiver Volume Control 11 Push in and Slide down
2Headset/Handset Selector Switch 12 Battery Compartment
3Mute 13 Screwdriver
4Headset Port 14 Telephone Port
5Transmit Volume Control 15 Install Batteries
6Security Cover 16 Adjust Volume Dial
77-position slide switch 17 On
8Battery Cover 18 Off Hook
9Handset Port 19 Listen to Dial Tone
10 Battery Installation 20 Set Receive Volume
Diagram Key
1 Receiver Volume Control
2 Headset/Handset Selector Switch
3 Mute
4 Headset Port
5 Transmit Volume Control
6 Security Cover
7 7-position slide switch
8 Battery Cover
9 Handset Port
10 Battery Installation
11 Push in and Slide down
12 Battery Compartment
13 Screwdriver
14 Telephone Port
15 Install Batteries
16 Adjust Volume Dial
17 On
18 Off Hook
19 Listen to Dial Tone
20 Set Receive Volume
Diagram Key
en
Instructions
AConnecting the M22 to your telephone and headset
Unplug the handset coiled cable from the telephone base and plug it
into the port labelled with the handset symbol on the M22.
Insert the coiled cable from the M22 port labelled with the
telephone symbol into the handset cord port on your telephone.
To connect your headset, put the 2 halves of the Quick Disconnect™
(QD) connector together. Your headset and M22 are both supplied
with QD connectors. (See diagram).
Refer to your headset user guide for further information on your
headset.
NOTE The telephone must be disconnected from the network before
installing the M22. Your telephone may have a special socket labelled
headset; if this is the case do NOT connect the handset to the M22.
Please check your telephone user guide to find out how to set up headset
operation on your telephone.
BAdjusting the M22
The M22 has been designed to work with most telephones. The
following instructions will help you to set up your M22 with your
telephone. Most telephones will work with the switch set in position
5. If this does not work try the other positions.
Installing batteries
The batteries on your M22 may need to be installed before you can
use your headset. You should disconnect your telephone from the
network before doing this.
To install the batteries, remove the battery cover on the side of the
M22 by pressing on the grips and pushing down.
Put the batteries into the compartment as shown on the inside of
the battery compartment, and replace the cover.
en
The M22 has a low battery indicator which gives 3 beeps when you
begin a call. If you hear this then replace the batteries as soon as
possible.
Setting the 7-position slide switch
The M22 is supplied pre-set to position 5. Try out the product at this
setting and adjust if necessary. Remove the mini-screwdriver from the
base of the M22 by sliding it out of the bracket. Use the screwdriver to
set the switch to the correct position for your telephone.
Fitting and removing the switch cover
On the left of the M22 is a cover. To remove it, hold the M22 firmly
and put your thumbs on the cover grips. Press and slide the cover
downwards. This gives you access to the adjustments for the transmit
level and the 7-position switch.
Adjusting the transmit level
The transmit level is how loud or quiet your voice is heard by people
on the other end of the line.
The M22 can be adjusted to set the optimum transmit level. However,
you need to fully install your headset before you make this adjustment.
When you have completed your headset installation, put on your
headset and make a call to a colleague. Use the screwdriver to adjust
the dial until the ideal sound and tone levels are reached. Turn the dial
clockwise to increase the sound level, anti-clockwise to decrease. The
sound level should be the same as when you are using the handset.
Once you have set this, the dial only needs adjusting if you change
your telephone.
When you have finished making adjustments, replace the security
cover and the screwdriver for future use.
Making and taking calls with the M22
Some phones can be programmed to allocate a button on the
telephone for headset use. This allows you to take a call by simply
en
en
pressing this button. Please refer to your phone user guide for
further instructions. For other phones, please follow the instructions
below.
The M22 has 2 modes –
1. Handset 2. Headset
To use the headset the green square indicator should be
showing on the headset switch. Press the button to switch between
the two settings.
To make a short call using the handset, press the headset button
on the top of the M22 so that the green square indicator does not
appear. Pick up your handset, dial and make the call as normal.
To make a call while wearing the headset, first lift off the handset
from the cradle. You should now hear the dialling tone and you can
dial and make the call as normal.
To take a call while wearing the headset, lift the handset off the
cradle when the phone rings.
Volume control
The M22 has a receive volume control, so you can adjust the volume
of your callers voice. To change the volume rotate the wheel until the
sound is at a comfortable listening level.
Mute button
The M22 has a mute button so that you can still hear the caller, but
they cannot hear you, for example, if you need to speak to a colleague
during a call. To do this press the mute button so that you can see the
green square indicator. Press the button again when you want your
caller to hear you.
Problem
I cannot hear callers/callers cannot hear me
Possible cause Remedy
Battery problem Check that the batteries are correctly installed
and that the cover is fitted properly
Incorrect setting of Refer to plantronics.com/compatibility
7-position switch and set to the correct position
Check transmit level Adjust to the recommended level as shown on
the compatibility chart and make a test call
Low receive volume Rotate the volume control on the top of the
Vista. To increase the volume turn the dial to
a higher number
Cables not plugged Check the connections to your telephone
in correctly and headset. Refer to the user guide for
instructions
Headset/Handset To use the Vista with your headset, make
setting incorrect sure that the green indicator is showing on
the switch
Mute function Your voice is muted if the green indicator is
switched on showing on the switch
Problem
Caller cannot hear you clearly
Possible cause Remedy
Your voice seems Only set the transmit level to the level that
unclear to your needed you clearly for your voice to be heard
callers clearly. Do not set this level too high.
M22 Troubleshooting Guide
Recycle where
facilities exist
©2013 Plantronics, Inc. All rights reserved. Plantronics
Vista and the logo design are trademarks or registered
trademarks of Plantronics, Inc. All other trademarks are the
property of their respective owners
82875-03 (09.13)
NEED MORE HELP?
plantronics.com/support
Plantronics, Inc.
345 Encinal Street
Santa Cruz, CA 95060
United States
Autres manuels pour Vista M22 Amplifier
6
Table des matières
Autres manuels Plantronics Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
