Planet WAP-1960 Manuel utilisateur

Wireless Access Point

WAP-1960

User’s Manual

publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or

translated into any language or computer language, in any form or by any means, electronic,

mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written

permission of PLANET.

Planet makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any

particular purpose. Any software described in this manual is sold or licensed "as is". Should

the programs prove defective following their purchase, the buyer (and not Planet, its distributor,

or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or

consequential damages resulting from any defect in the software. Further, Planet reserves the

right to revise this publication and to make changes from time to time in the contents hereof

without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered

trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/television technician for help.

Notice 1:

The changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Notice 2:

Shielded interface cables, if any, must be used in order to comply with the emission limits.

TABLE OF CONTENTS

INTRODUCTION

..........................................................................5

1.1 Package Contents.........................................................................................5

1.2 System Requirements...................................................................................5

1.3 Features ........................................................................................................6

1.4 Specification.................................................................................................. 7

INSTALLATION ...........................................................................8

2.1 Hardware Connection....................................................................................8

CONFIGURING THE WIRELESS ACCESS POINT..............................9

3.1 Configure through DFU utility........................................................................9

3.2 Configure through SNMP Manager.............................................................14

APPLICATION

..........................................................................26

4.1 Wireless Access Point.................................................................................26

4.2 Wireless AP Client Mode.............................................................................27

4.3 LAN to LAN Bridging through WAP-1960 ...................................................28

4.4 Multiple LAN to LAN Bridging through WAP-1960......................................29

TROUBLESHOOTING..................................................................30

5.1 Frequently Asked Questions.......................................................................30

APPENDIX

................................................................................32

CHAPTER 1

Introduction

Thank you for purchasing WAP-1960. This device features the latest innovation

wireless technology making the wireless networking world happened. This manual

guides you on how to install and properly use the WAP-1960 in order to take full

advantage of its features.

1.1 Package Contents

Make sure that you have the following items:

• One WAP-1960

• One AC Power Adapter

• One USB Cable (For Configuration)

• One CD-ROM with AP manager Software and Installation Manual

• One Quick Installation Guide

If any of the above items are missing, contact your supplier as soon as possible.

1.2 System Requirements

Before installation, please check the following requirements with your equipment.

• Pentium Based (And Above) IBM-Compatible PC System

• CD-ROM drive

• One Available USB Connector

• Windows 98/ME/2000/XP Operating System with TCP/IP protocol

1.3 Features

 Four operation modes selectable: AP / AP Client / Wireless bridge* Point

to Point and Wireless bridge Point to Multipoint

 Highly Efficient Dipole Antennas Provide Extensive Range of Operation

 Auto Fall-Back Data Rate for Long-Distance Communication and Noisy

Environments

 High-Speed Data Transmitter Rate Up to 11 Mbps

 Interoperable with IEEE 802.11b (DSSS) 2.4GHz-Compliant Equipment

 Features Roaming, Best Access Point Selection, Load Balancing, and Network

Traffic Filtering

 64-Bit and 128-Bit Wired Equivalent Privacy

 Support 63 clients to connect the network. (For best performance, the suggested

maximum clients number of one WAP-1960 is 25.)

 Software Driver Upgrades

* Terms “Wbridge” in the following sections

1.4 Specification

• Standard IEEE 802.11b

• Signal Type DSSS (Direct Sequence Spread Spectrum)

• Modulation QPSK / BPSK / CCK

• Port One RJ-45 / One 10BASE-T

• Ethernet Interface IEEE802.3 10 BASE-T

• Antenna Dual Dipole Antenna

• Data Encryption

64 bit / 128 bit WEP encryption

• Frequency 2.4GHz - 2.4835GHz

• Channel 11 Channels (US, Canada)

13 Channels (Europe)

14 Channels (Japan)

4 channels (France)

2 channels (Spain)

• Data Rate Up to 11Mbps(with automatic scale back)

• LED Indicators Power, Activity (wireless), Link (wired)

• Power Requirement

5V DC, 2A

• Temperature Operating :0 degree C to 40 degree C,

Storage: -20 degree C to 70 degree C,

• Humidity 90% Non-Condensing

• Dimensions 206 x 142 x 35mm

• Output Power 14dBm

• Antenna Gain 1dBi

• Antenna Connector Reversed Polarity SMA Male

• Transmission

Antenna ANT A*

• Receive Antenna ANT A, ANT B

* For external antenna or directional antenna connection, ANT A is the dedicated connector.

CHAPTER 2

Installation

Before you proceed with the installation, it is necessary that you have enough

information about the WAP-1960.

2.1 Hardware Connection

1. Locate an optimum location for the WAP-1960. The best place for your

WAP-1960 is usually at the center of your wireless network, with line of sight to all of

your mobile stations.

2. Assemble the antennas to WAP-1960. Try to place them to a position that can

best cover your wireless network. The antenna’s position will enhance the receiving

sensitivity.

3. Connect RJ-45 cable to WAP-1960. Connect this WAP-1960 to your LAN

switch/hub or a single PC.

4. Connect USB cable to WAP-1960 USB port. If you are first time to configure

WAP-1960, please connect the USB cable for DFU configuration. Before USB cable

connected, please ensure you have install DFU utility to your PC already.

5. Plug in power adapter and connect to power source. After power on, WAP-1960

will start to work.

Note: ONLY use the power adapter supplied with the WAP-1960. Otherwise, the

product may be damaged.

CHAPTER 3

Configuring the Wireless Access Point

3.1 Configure through DFU utility

The DFU Utility is provided to configure the WAP-1960 setting through the USB port.

Note: If this is your first time to configure WAP-1960, we suggest installing DFU

utility for configuration. Before connect WAP-1960 to your PC, please ensure

DFU utility had been installed to your OS. DFU installation will also install

WAP-1960 USB driver. When Windows detect WAP-1960 from USB port and

ask for the driver, click “Next” for Windows to automatically find the installed

driver.

Installing the DFU Utility

Insert the Driver and Users Manual CD into your CD drive (suppose E:\) and

execute the “DFU.EXE” which is in E:\Utility\WAP1960\.

Then the wizard box will appears, please click “ Next “.

Choose the destination folder that you want to install utility and click “Next” to

continue.

After installation finish, please click “Finish “to complete the installation. And then

please restart your PC.

Configuring the Wireless Network Access Point with the DFU Utility

 Run the DFU utility form Start -> Programs ->Planet -> DFU, the following dialog

will appear.

Note: If this is your first time to use the DFU utility to configure the Access Point, you

can select “Access Point Wizard” as show above to set the basic settings of

WAP-1960 (IP Address, SSID, Radio Channel). Or you may click the

“Configuration” to get more advanced settings. But, please be sure that you

have got enough information and authorization to set the advance setting.

Table des matières

Autres manuels Planet Point d'accès sans fil

Planet

Planet IAP-2000PS Manuel utilisateur

Planet

Planet WAP-4060PE Manuel utilisateur

Planet

Planet WDAP-W7200AC Manuel utilisateur

Planet

Planet WNAP-3000PE Manuel utilisateur

Planet

Planet WAP-4036 Manuel utilisateur

Planet

Planet IAP-2000PS Manuel utilisateur

Planet

Planet WAP-1000 WireFree Manuel utilisateur

Planet

Planet WAP-4060PE Manuel utilisateur

Planet

Planet WDAP-C7200E Manuel utilisateur

Planet

Planet WDAP-C7200AC Manuel utilisateur

Planet

Planet WNAP-6308 Manuel utilisateur

Planet

Planet WBS-502AC Manuel utilisateur

Planet

Planet WDAP-C3000AX Manuel utilisateur

Planet

Planet WAP-8000 Manuel utilisateur

Planet

Planet EPN-402NV Manuel utilisateur

Planet

Planet WAP-1963 Manuel utilisateur

Planet

Planet WDAP-C7200AC Manuel utilisateur

Planet

Planet WBS-502AC Manuel utilisateur

Planet

Planet Network Device WAP5 Manuel utilisateur

Planet

Planet WNAP-7320 Manuel utilisateur

Planet

Planet Network Device WAP-4033PE Manuel utilisateur

Planet

Planet WNAP-6350 Manuel utilisateur

Planet

Planet WNAP-6305 Manuel utilisateur

Planet

Planet MAP-3120 Manuel de programmation

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur