Planet WAP-4036 Manuel utilisateur

802.11g Wireless Access Point

WAP-4036

Quick Installation Guide

Table of Contents

Package Content............................................................................. 3

Hardware Installation ...................................................................... 4

Initial Conguration......................................................................... 5

Further Conguration ...................................................................... 8

Package Content

1 x WAP-4036

1 x Power Adapter

1 x User’s Manual CD

1 x Quick Installation Guide

1 x External Antenna

1 x Ethernet Cable

Note

If any of the above items are missing or damaged,

contact your local dealer for support.

Hardware Installation

Before you proceed with the installation, it is necessary that you have

enough information about the WAP-4036.

Keep the access point as central in your work area as possible.

Signal strength and speed fall off with distance.

Higher is often better. For instance, set it up on the top shelf of a

bookcase rather than the bottom one, if possible.

Prior to connecting the hardware, make sure to power off your Ethernet

device and Wireless Access Point (AP). Then follow the steps below to

connect the related devices.

Step 1: Connect your computer to the LAN port of WAP-4036

by using RJ-45 cable. Attach one end of the Ethernet cable

with RJ-45 connector to your hub, switch or a computer’s

Ethernet port, and the other end to one of the LAN ports of

your AP.

Step 2: Assemble the antenna to WAP-4036. Try to place them

to a position that can best cover your wireless network. The

antenna’s position will enhance the receiving sensitivity.

Step 3: Connect the power adapter. Connect the single DC output

connector of the power adapter to the power jack on the side

of the AP. Then plug the Power Adapter into an AC outlet.

Step 4: Power on the following devices in this order: HUB or

Switch, AP, and PCs

ONLY use the power adapter supplied with the WAP-

4036. Otherwise, the product may be damaged. If you

want to reset your WAP-4036 to default settings, press

the Reset button 5 second. Then release the button and

wait for 10 seconds for rebooting.

Initial Conguration

1. Open your web browser.

2. Enter WAP-4036 IP address (default IP address is http://192.168.1.1)

into the address eld of the web browser. Please also make sure your

PC’s IP address is in the same IP range with WAP-4036.

Note

If the AP’s LAN port has been changed with new IP

address, enter the new IP address instead.

3. A User Name and Password dialog box will appear. Please enter your

User Name and Password here. The User Name and Password are

“admin” by default. Click “OK” to access the management page.

4. Once you log in, the Conguration Wizard and Status page will pop

up at the same time. Conguration Wizard will appear every time

you enter WAP-4036. If you do not want to display wizard by itself

next time, select “don’t pop up” option and click “save”. In the

future, you can still have wizard appeared by clicking “Wizard” tab

on upper right panel of WAP-4036’s web page.

Click “Start” to go to next step.

Note

In order to start the wizard, you will need to have the

pop-up blocker DISABLED in your web browser.

5. On this page, you can set the Radio Band, Mode, SSID and Channel

to your WAP-4036. The SSID is to identify your wireless network.

All the devices (AP and wireless client) on the same wireless network

must be congured to the same SSID.

You can leave the Radio Bnad and Channel settings to default. On

the Mode Settings, the default is AP mode which allow your wireless

client to connect each other and the wired Ethernet network. Please

refer to the user’s manual for detial on other available modes.

Click “Next” to proceed.

6. You have nished all basic congurations for WAP-4036. Please press

“Exit” to close this window. The WAP-4036 will perform reboot if

major changes are made. After reboot completes, the WAP-4036 is

ready to use.

Further Conguration

If you want to congure more detail settings of WAP-4036, please refer

to the manual in the bundled CD. If you have any difculty on resolving

the problem while installing or using the WAP-4036, please feel free to

contact PLANET for support.

Table des matières

Autres manuels Planet Point d'accès sans fil

Planet

Planet 802.11g Wireless Access Point / Bridge... Manuel utilisateur

Planet

Planet WAP-7000 Manuel utilisateur

Planet

Planet WAP-900 Manuel utilisateur

Planet

Planet WNAP-7205 Manuel utilisateur

Planet

Planet MAP-3100 Guide de démarrage rapide

Planet

Planet WAP-4060PE Manuel utilisateur

Planet

Planet Network Device WAP-4033PE Manuel utilisateur

Planet

Planet WDAP-C7200AC Manuel utilisateur

Planet

Planet Network Device WAP5 Manuel utilisateur

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manuel utilisateur

Planet

Planet WNAP-1110 Manuel utilisateur

Planet

Planet WNAP-6350 Manuel utilisateur

Planet

Planet WAP-1000 WireFree Manuel utilisateur

Planet

Planet WDAP-C7210E Manuel utilisateur

Planet

Planet WAP-2000 Manuel utilisateur

Planet

Planet WAP-1960 Manuel utilisateur

Planet

Planet WDAP-3000AX Manuel utilisateur

Planet

Planet WDAP-802AC Manuel utilisateur

Planet

Planet WAPC-1232HP Manuel utilisateur

Planet

Planet WAP-4033 Manuel utilisateur

Planet

Planet WAP-8000 Manuel utilisateur

Planet

Planet Network Device WAP-4033PE Manuel utilisateur

Planet

Planet WDAP-C1800AX Manuel utilisateur

Planet

Planet WNAP-6325 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur