Planet IGS-5225-8P4S-12V Manuel utilisateur

Industrial L2+ Multi-Port Full Gigabit

Managed Ethernet Switch

IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S

IGS-5225-8P4S/IGS-5225-8P4S-12V

IGS-5225-8P2T2S/IGS-5225-8P2T4S

Quick Installation Guide

Table of Contents

1. Package Contents...................................................................... 3

2. Requirements............................................................................ 5

3. Wiring the Power Inputs ............................................................ 6

3.1 Grounding the Device.......................................................... 8

4. Terminal Setup.......................................................................... 9

4.1. Logging on to the Console..................................................10

 4.2 ConguringIPaddress .......................................................11

5. Starting Web Management ........................................................13

5.1 Logging in to the Industrial Managed Switch ........................13

 5.2 SavingCongurationviaWeb .............................................16

6. RecoveringBacktoDefaultConguration ...................................17

7. Customer Support ....................................................................20

1. Package Contents

Thank you for purchasing PLANET L2+ Industrial Managed Switch,

IGS-5225 Series. The number of the ports of these models is as

follows:

GbE Copper

Ports PoE Ports GbE SFP Ports

IGS-5225-4T2S 4 - 1G/2.5G: 2

IGS-5225-4P2S 4at/af: 4 2

IGS-5225-4UP1T2S 5at/bt: 4 2

IGS-5225-8P4S 8at/af: 8 1G: 2

1G/2.5G: 2

IGS-5225-8P4S-12V 8at/af: 8 1G: 2

1G/2.5G: 2

IGS-5225-8P2T2S 10 at/af: 8 1G/2.5G: 2

IGS-5225-8P2T4S 10 at/af: 8 1G: 2

1G/2.5G: 2

“Industrial Managed Switch” mentioned in this Quick Installation

Guide refers to the above models.

Open the box of the Industrial Managed Switch and carefully

unpack it. The box should contain the following items for each model of

the Industrial Managed Switch:

The

Industrial

Managed

Switch

Quick

Installation

Guide

Wall

Mounting

Kit

DB9 to

RJ45,

RS232

Console

Cable

RJ45

Dust

Cap

SFP

Dust

Cap

IGS-5225-

4T2S     5 2

IGS-5225-

4P2S     5 2

IGS-5225-

4UP1T2S     6 2

IGS-5225

-8P4S     9 4

IGS-5225-

8P4S-12V     9 4

IGS-5225-

8P2T2S     11 2

IGS-5225-

8P2T4S     11 4

If any of these are missing or damaged, please contact your dealer

immediately. If possible, retain the carton including the original packing

materials to enable you to repack the product in case there is a need

to return it to us for repair.

2. Requirements

The Industrial Managed Switch provides remote login interface for

management purposes. The following equipment is necessary for

further management:

zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS

X or later, Linux, UNIX, or other platforms are compatible with TCP/

IP Protocols.

zWorkstations are installed with Ethernet NIC (Network Interface

Card)

zSerial Port Connection (Terminal)

The above Workstations come with COM Port (DB9) or USB-to-

RS232 converter.

The above Workstations have been installed with terminal

emulator, such as Hyper Terminal included in Windows XP/2003,

putty or tera term.

Serial cable -- one end is attached to the RS232 serial port,

while the other end to the console port of the Industrial Managed

Switch.

zEthernet Port Connection

Network cables -- Use standard network (UTP) cables with RJ45

connectors.

The above PC is installed with Web browser.

Note

It is recommended to use Internet Explorer 8.0 or above

to access the Industrial Managed Switch.

3. Wiring the Power Inputs

The Upper Panel of the Industrial Managed Switch comes with one

6-contact terminal block. Please follow the steps below to insert the

power wire.

1. Insert positive/negative DC power wires into Contacts 1 and 2 for

Power 1, or Contacts 5 and 6 for Power 2.

IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S: DC 48~56V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-56V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel

IGS-5225-8P4S-12V: DC 12~54V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

12-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-2: IGS-5225-8P4S-12V Upper Panel

IGS-5225-4T2S: DC 12~48V, AC 24V

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 1.7A max.

AC Input: 24V

, 1A max.

V1+ V2+

PWR1 PWR2Alarm

1 2 3 4 5 6

Figure 3-3: IGS-5225-4T2S Upper Panel

IGS-5225-4P2S: DC 48~56V

FaultPWR1

V1+ V2+

PWR2

Max. fault loading: 24V, 1A

DC Input: 48-56V

3.5A max.

1 2 3 4 5 6

Figure 3-4: IGS-5225-4P2S Upper Panel

IGS-5225-4UP1T2S: DC 48~56V

PWR1 PWR2

Fault

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-56V , 6A max.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

Figure 3-5: IGS-5225-4UP1T2S Upper Panel

2. Tighten the wire-clamp screws for preventing the wires from loos-

ening.

123456

V+ V- V+ V-

Power 1 Power 2

Positive (+) Pin Negative (-) Pin

IGS-5225 Series Pin 1/5 Pin 2/6

Note

1. The wire gauge for the terminal block should be in

the range from 12 to 24 AWG.

2. Please check the wire AWG Ampere specification

before connecting PLANET Industrial Managed Switch.

Caution

PWR1 and PWR2 must provide the same DC voltage

for power load balance while operating with dual power

input.

3.1 Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a

sudden lightning could cause fatal damage to the device.

PWR1 PWR2

Fault

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-56V , 6A max.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

Earth Ground

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a

PC or notebook computer and to RJ45 type serial (console) port of the

Industrial Managed Switch. The console port of the Industrial Managed

Switch is DCE already, so that you can connect the console port

directly through PC without the need of null modem.

PC/Workstation with

Terminal Emulation Software

RJ45 to DB9 RS232 Cable

Serial Port

Console Port

115200,N,8,1

IGS Industrial Managed Switch

Console

115200,N,8,1

P1 P2 Fault

DIDO

Ring

R.O.

PoE Usage

ACT1000 LNK

ACT100 LNK

A terminal program is required to make the software connected to the

IGS-5225 series Industrial Managed Switch.

1. Run terminal program on the OS.

2. When the following screen appears, make sure that the COM port

shouldbeconguredas:

zBaud: 115200

zParity: None

zData bits: 8

zStop bits: 1

zFlow control: None

4.1. Logging on to the Console

Once the terminal has been connected to the device, power on the

Industrial Managed Switch and the terminal will display “running testing

procedures”.

Note

The following terminal configuration of the IGS-

5225-4UP1T2S is taken for an example.

Then, the following message asks to log in user name and password.

The default user name and password are shown as follows and the

User name: admin

Password: admin

Figure 4-1: Console Login Screen

The user can now enter commands to manage the Industrial Managed

Switch. For a detailed description of the commands, please refer to the

following chapters.

Note

1. For security reason, please change and memorize

the new password after this first setup.

2. Only accept command in lowercase letter under

console interface.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Planet Changer

Planet

Planet XGS3-24042 Manuel utilisateur

Planet

Planet XGS-5240-24X2QR Manuel utilisateur

Planet

Planet WGSW-24040 Manuel utilisateur

Planet

Planet IPM-4220 Manuel utilisateur

Planet

Planet POE-1200G Manuel utilisateur

Planet

Planet GSD-800S Manuel utilisateur

Planet

Planet IKVM-8020 Manuel utilisateur

Planet

Planet WGS-803 Manuel utilisateur

Planet

Planet POE-152 Manuel utilisateur

Planet

Planet VC-810S Manuel utilisateur

Planet

Planet SGS-5220-24T2X Manuel utilisateur

Planet

Planet ISW-800T-M12 Manuel utilisateur

Planet

Planet MGSD-10080F Manuel utilisateur

Planet

Planet POE-1200 Manuel utilisateur

Planet

Planet UH-421 Manuel utilisateur

Planet

Planet FNSW-1600P Manuel utilisateur

Planet

Planet GSD-800S Manuel utilisateur

Planet

Planet IGS-1020TF Manuel utilisateur

Planet

Planet FSD-805S15 Manuel utilisateur

Planet

Planet NOVASwitch Series Manuel utilisateur

Planet

Planet FNSW-2402 Manuel utilisateur

Planet

Planet FSD-808HP Manuel utilisateur

Planet

Planet GSD-1020 Manuel utilisateur

Planet

Planet KVM-800 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur