Planet Networking & Communication ISW-504PT Manuel utilisateur

Industrial 5-Port Ethernet Switch

with 4-Port PoE+

ISW-504PT/ISW-514PTF

User’s Manual

Table of Contents

1. Package Contents................................................................................. 3

2. Hardware Introduction .......................................................................... 4

2.1 Switch Front Panel......................................................................... 4

2.2 LED Indicators............................................................................... 6

2.3 Switch Upper Panel........................................................................ 7

2.4 Wiring the Power Inputs................................................................. 7

2.5 Wiring the Fault Alarm Contact ....................................................... 9

2.6 Grounding the Device................................................................... 10

3. Installation ........................................................................................ 11

3.1 DIN-rail Mounting Installation ....................................................... 11

3.2 Wall-mount Plate Mounting ........................................................... 12

3.3 Side Wall-mount Plate Mounting.................................................... 12

4. Troubleshooting.................................................................................. 13

5. Customer Support .............................................................................. 14

1. Package Contents

Thank you for purchasing PLANET 5-Port Industrial Ethernet Switch with 4-Port

PoE+, ISW-504PT/ISW-514PTF. The interfaces of these models are shown

below:

Model Name 10/100Mbps RJ45 Ports 100FX SFP Slots PoE+ Ports

ISW-504PT 5 - 4

ISW-514PTF 4 1 4

In the following section, the term “Industrial PoE+ Switch” means the

ISW-504PT/ISW-514PTF.

Open the box of the Industrial PoE+ Switch and carefully unpack it. The box

should contain the following items:

Industrial PoE+ Switch x 1 QR Code Sheet x 1

Let’s get started with your PLANET product

ISW-514PTF

EN Please scan the QR code to browse our online User’s Manual or Quick

Installation Guide and follow the instructions to complete the setup.

User's Manual

Bitte scannen Sie den QR- Code sie werden per Browser zur

Bedienungsanleitung oder Schnellanleitung weiter geleitet. Folgen Sie den

Anweisungen um die Installation abzuschließen.

Veuillez scanner le code QR pour obtenir notre Notice d’Utilisation en

ligne ou notre Guide d’Installation Rapide et suivez les instructions pour

compléter la conguration

Escanee el código QR para encontrar el Manual del Usuario en línea o

la Guía de Instalación Rápida y siga las instrucciones para completar la

conguración.

IT Scansiona il codice QR per consultare online il Manuale utente o la Guida di

installazione rapida e segui le istruzioni per completare la congurazione.

PT Por favor, escaneie o QR code paranavegar no Manual do Usuário ou Guia

de Instalação Rápida. Siga as instruções para completar a conguração.

Zeskanuj kod QR, aby otworzyć naszą internetową instrukcję obsługi

lub instrukcję szybkiej instalacji. Postępuj zgodnie z instrukcjami, aby

zakończyć poprawną kongurację.

One word modify: Отсканируйте QR-код, чтобы просмотреть наше

онлайн-руководство пользователя или руководство по быстрой

настройке, и следуйте инструкциям для завершения настройки

RO Te rugam sa scanezi codul QR, pentru a descarca User’s Manual sau Quick

Installation Guide si a urmari instructiunile necesare in nalizarea instalarii

Need more help?

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq

Technical Support: [email protected]

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Part No. 2360-AH0360-000

Dust Cap x 5 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your dealer

immediately.

2. Hardware Introduction

2.1 Switch Front Panel

P1 P2 Alarm

120W

PoE Usage

90W

60W

30W

LNK ACT

PoE-in-Use

ISW-504PT

10/100TX

LNK/

ACT

DIP

1~4

VLAN

Extended

OFF

Standard

1 2 3 4 5

ONDIP

LNK ACT

PoE-in-Use

ISW-514PTF

P1 P2 Alarm

100FX

DIP

1~4

VLAN

Extended

OFF

Standard

120W

PoE Usage

90W

60W

30W

1 2 3 4 5

ONDIP

Figure 2-1: ISW-504PT front panel Figure 2-2: ISW-514PTF front panel

1. Fast Ethernet TP Interfaces

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

2. 100BASE-FX SFP Slot (ISW-514PTF)

100BASE-FX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver

module: From 2 kilometers (multi-mode ber) to 20/40/60/120 kilometers

(single-mode ber).

3. DIP Switch

The Industrial PoE+ Switch provides one DIP switch for Standard, VLAN

and Extended mode selections. The detailed descriptions are shown in the

following table.

DIP Switch Mode Function

Standard

Switches 1 to 5 are o

This mode makes the Industrial PoE+ Switch operate as

a general switch and all PoE ports operate at 10/100Mbps

auto-negotiation.

VLAN

Switch 5 is on

This mode makes the Industrial PoE+ Switch operate as a

VLAN isolation switch and

1. Port 1 to 4 will isolate respectively.

2. Port 1 to 4 can only communicate with port 5.

After adjusting VLAN DIP switch, reboot

the Industrial PoE+ Switch to make the

change take effect.

Extend Any of switches 1 to 4 is on

This mode makes the Industrial PoE+ Switch operate on

a per-port basis at 10Mbps full duplex operation but can

support IEEE 802.3af PoE power output over a distance of

up to 250 meters overcoming the 100m limit on Ethernet

UTP cable.

2.2 LED Indicators

System

LED Color Function

P1 Green Lights: indicates power 1 has power.

P2 Green Lights: indicates power 2 has power.

Alarm Red Lights: indicates either power 1 or power 2 has no power.

30W Amber

O: indicates the PoE usage is less than 14W.

Blinks: indicates that the PoE usage is around 15W to 29W.

Lights: indicates the PoE usage is around/over 30W.

60W Amber Blinks: indicates that the PoE usage is around 45W to 59W.

Lights: indicates the PoE usage is around/over 60W.

90W Amber Blinks: indicates that the PoE usage is around 75W to 89W.

Lights: indicates the PoE usage is around/over 90W.

120W Amber

Blinks: indicates that the PoE usage is around 100W to

119W.

Lights: indicates the PoE usage is at the maximum.

Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 4)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is successfully

established at 10Mbps or 100Mbps.

Blinks: indicates that the switch is actively sending or

receiving data over that port.

PoE -

in-Use Amber

Lights: indicates the port is providing DC in-line power.

O: indicates the connected device is not a PoE powered

device (PD).

Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is successfully

established at 10/100Mbps.

Blinks: indicates that the switch is actively sending or

receiving data over that port.

Per 100FX SFP Slot (Port 5 of ISW-514PTF)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is successfully

established at 100Mbps.

Blinks: indicates that the switch is actively sending or

receiving data over that port.

2.3 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one terminal block

connector within two DC power inputs.

Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.

Max. Fault Alarm Loading: 24V, 1A

DC Input:

12-54V , 7A max.

V1+ V2+

PWR1 Alarm PWR2

1 2 3 4 5 6

Figure 2-3: Industrial PoE+ Switch Upper Pane

2.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial PoE+

Switch is used for two DC redundant power inputs. Please follow the steps

below to insert the power wire.

When performing any of the procedures like inserting the wires

or tightening the wire-clamp screws, make sure the power is

OFF to prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2 for

POWER 1, or 5 and 6 for POWER 2.

Max. Fault Alarm Loading: 24V, 1A

DC Input:

12-54V , 7A max.

V1+ V2+

PWR1 Alarm PWR2

1 2 3 4 5 6

DC Input Max. PoE Budget

12V 60W

24v 90W

48V-54V 120W

To avoid damage, please use the Industrial PoE+ Switch under

its specification.

2. Tighten the wire-clamp screws for preventing the wires from loosening.

123456

Power 1 Alarm Power 2

+ - + -

The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as

the picture shows below. Inserting the wires, the Industrial PoE+ Switch will

detect the fault status of the power failure and then forms an open circuit. The

following illustration shows an application example for wiring the fault alarm

contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Alarm

Insert the wires into the fault alarm contacts

1. The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V, max. 1A currents.

2.6 Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden

lightning could cause fatal damage to the device.

Max. Fault Alarm Loading: 24V, 1A

DC Input:

12-54V , 7A max.

V1+ V2+

PWR1 Alarm PWR2

1 2 3 4 5 6

Earth Ground

EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Planet Networking & Communication Changer