Pittway NOTIFIER LDM Series Manuel utilisateur

Document15885

10/29/97 Rev: F

P/N15885:F2 ECN97-407

12 Clintonville Road

Northford, CT 06472

(203) 484-7161

FAX: (203) 484-7118

LDM Series

Lamp Driver Modules

For Graphic Annunciation and Control

Used with the System 500, System 5000,

AM2020/AFP1010 and AFP-200

Fire Alarm Control Panels

www.PDF-Zoo.com

215885 Rev. F1 8/2/95 P/N 15885:F1

INSTALLATIONWARNING

www.PDF-Zoo.com

15885 Rev. F1 8/2/95 P/N 15885:F1 3

Table of Contents

Section One: Introduction to the LDM Series 5

SectionTwo: LDM Features 6

2.1 The LDM-32 6

Figure 2-1: LDM-32 6

2.2 The LDM-E32 7

Figure 2-2: LDM-E32 7

2.3 Connectors on the LDM-32 and LDM-E32 8

2.4 Switches 9

2.5 Terminal Blocks 9

2.6 Cables 10

2.7 The LDM-R32 11

Figure 2-3: LDM-R32 11

SectionThree: Installation 12

3.1 External Cabinets 12

3.2 CHS-4L Chassis 12

Figure 3-1: CHS-4L Mounting 12

Figure 3-2: Installing LDM Modules in CHS-4L 13

Figure 3-3: LDMs Mounted in UL Listed Cab 13

Figure 3-4: Mounting Optional LDM-R32 Relay Mod. 14

Section Four: Wiring Considerations 15

4.1 Limits 15

4.2 Wire Runs 15

Figure 4-1: EIA-485 Communications 15

4.3 Wiring Specifications 15

Figure 4-2: Wiring the Enclosure 16

4.4 EIA-485 Shield in Conduit 16

Figure 4-3: Terminating the Shield - Conduit 16

4.5 EIA-485 Shield Not in Conduit 16

Figure 4-4:Terminating the Shield - No Conduit 16

4.6 EIA-485, Power and Relay Wiring 17

Figure 4-5: Wiring Multiple LDMs (6000 ft. max..) 17

Figure 4-6: Wiring Supervision Terminals 17

UL Power Limited Wiring Requirements 18

4.7 Remote Power Supply Connector 19

Figure 4-7: Remote Power Supply Connections 19

4.8 Lamp/LED Wiring 20

Figure 4-8:Typical LDM-to-Graphics @ 5 VDC 20

Figure 4-9:Typical LDM-to-Graphics @ 24 VDC 20

4.9 Control Switch Wiring 21

Figure 4-10: Optional Zone/Pt. Control Switch Wire 21

Section Five: Summary - Installing the Lamp Driver Module 22

Section Six: Operating the Lamp Driver Module 24

6.1 Lamp Test/Acknowledge 24

6.2 On Line LED 24

6.3 Graphic Annunciator Lamp/LED 24

www.PDF-Zoo.com

415885 Rev. F1 8/2/95 P/N 15885:F1

Section Seven: LDM Communications 25

Figure 7-1: LDM-32 Supervision 25

Section Eight: LDM Electrical Ratings & Current Calculations 26

Appendix A: LDM and the System 5000 29

Table A-1: Annunciator Point Assignments 30

AIM-200 Point Assignments 31

Table A-2: LDM Switch Control Functions 32

Figure A-1: Alarm Only Operation w/o 8-Point Shift 33

Figure A-2: Alarm Only Operation with 8-Point Shift 34

Figure A-3: Alarm/Trouble Op. w/o 8-Point Shift 35

Figure A-4: Alarm/Trouble Op. with 8-Point Shift 36

Figure A-5: Alarm Relays with LDM-R32 37

Figure A-6: Alarm Relays with 8-Point Shift 38

Figure A-7: Alarm & Trbl Relays with LDM-R32 39

Figure A-8: Alarm & Trbl Relays with 8-Point Shift 40

Appendix B: LDM and the AM2020/AFP1010 41

Figure B-1: The EIA-485 Loop 42

Table B-1: Lamp Driver Point Functions 43

Figure B-2: Lamp Driver Alarm Points 45

Figure B-3: Alarm and Trouble Points 46

Figure B-4: Alarm-Only Relay Operation 47

Figure B-5: Alarm & Trbl Relay Operation 48

Appendix C: LDM and the System 500 49

Figure C-1: Connecting the EIA-485 Loop 49

Table C-1: Annunciator Point Assignments 51

Table C-2: LDM Switch Control Functions 52

Figure C-2: Alarm Points Only Operation 52

Figure C-3: Alarm Only Operation with CPU Shift 53

Figure C-4: Alarm and Trouble Points Operation 53

Figure C-5: Alarm/Trouble Operation with 8-Pt Shift 54

Figure C-6: Alarm Relays with LDM-R32 54

Figure C-7: Alarm Relays with 8-Point Shift 55

Figure C-8: Alarm and Trouble Relay with LDM-R32 56

Figure C-9: Alarm & Trbl Relays with 8-Point Shift 57

Appendix D: LDM and the AFP-200 58

Table D-1: LDM Switch Control Functions 60

Figure D-1: Display Active Status of Software Zones 61

Figure D-2: Active Status of Zones with 8-Pt Shft 62

Figure D-3: Activation and Trbl Status Annunciation 63

Figure D-4: Activation Operation with 8-Pt Shift 64

www.PDF-Zoo.com

15885 Rev. F1 8/2/95 P/N 15885:F1 5

Section One: Introduction to the LDM Series

The LDM Series Lamp Driver Modules, which consist of the LDM-32 master and LDM-E32

expander modules, are used to provide an interface to a custom graphic annunciator. The

master module provides power and control for a maximum of three expander modules.

The LDM-32 and LDM-E32 have output connectors which are used to drive lamps or LEDs

and input connectors which are used for remote switch functions.

The LDM Series Lamp Driver Modules may be connected to fire alarm control panels

(FACP) to provide remote annunciation of the following:

• General system status:

ü General Alarm

ü General Trouble

ü General supervisory

ü Notification Appliance Circuit (NAC) output status

ü Municipal tie status

ü System silence

ü Alarm relay status

• Alarm and trouble status of zones or individual points

• Alarm only status of zones or individual points

The LDM Series Modules also interface to remote control switches which may be used to

provide:

• System reset

• System silence

• System acknowledge

• Temporary activation of NAC outputs

• Alarm relay activation

• Other control functions

The LDM Series Modules interface to the host fire alarm control panel via an EIA-485

communications bus circuit. A maximum of 32 LDM-32s may be connected to the power-

limited EIA-485 bus, but if other types of devices are also connected to the EIA-485 bus,

the maximum number of LDM-32s must be reduced by the total of such devices. The EIA-

485 wiring distance must not exceed 6,000 feet and cannot be T-tapped. Multiple LDM-

32s may be used to annunciate duplicate information.

Power to the LDM-32s is typically provided by the host FACP and must be power-limited

regulated 24 VDC. External UL listed battery backed power supplies may also be used.

Careful consideration must be given to system battery calculations when power for the

LDM modules and lamps or LEDs is provided by the host FACP

. Refer to the specifications

in the appropriate FACP technical manual when making these calculations.

www.PDF-Zoo.com

615885 Rev. F1 8/2/95 P/N 15885:F1

SectionTwo: LDM Features

2.1The LDM-32

The Lamp Driver Module LDM-32 has 32 alarm lamp/LED driver outputs which sink current

to system common (-) on activation. A single positive (+) voltage is required to supply total

operating power for all lamps or LEDs when all drivers are activated. The LDM-32 provides

a separate driver for system trouble and inputs for a local lamp test switch. A maximum of

16 external control switches may be wired to the LDM-32. DIP switch SW3 is used to enable

or disable the onboard piezo, enable remote switch functions, select a flashing LED function

for new alarms and troubles, and other functions. Switch SW4 is used to configure the

module to annunciate 32 alarms or 16 troubles. A green ON LINE LED flashes to indicate

ongoing communications with the host FACP. One LDM-32 supports up to 3 LDM-E32

modules. The LDM-32 is supplied with 4 standoffs and screws for mounting to a CHS-4L

chassis or custom backbox.

Figure 2-1: LDM-32

Lamp Power (+24VDC)

SystemTrouble

Ribbon Cable

Connectionto

LDM-E32

OutputConnectors

for Wiring to LEDs

Security Key

SwitchTerminal

Terminal for max.

of 16 external

controlswitches

Address

Switches

LDMProgram

Switch

IndicatesEIA-485

CommunicationActive

Alarm or

Alarm/Trbl

EIA-485 In (-)

EIA-485 Out (-)

EIA-485 Out (+)

EIA-485 In (+)

Supervision

Inputs (NC)

Common In (-)

Common Out (-)

Power In +24VDC

Power Out +24VDC

Earth Ground

Power-

limited

Relay Power Ribbon

CableConnection

www.PDF-Zoo.com

15885 Rev. F1 8/2/95 P/N 15885:F1 7

2.2The LDM-E32

Each LDM-E32 expander module provides 32 additional lamp/LED driver outputs from J5,

J6, J7 and J8. The expander module has a slide switch SW4 for selecting alarm or alarm

and trouble annunciation and an input for a local lamp test switch. In alarm mode, use only

one LDM-32 and one LDM-E32 for a maximum of 56 alarm indicators and 8 system status

indicators. In alarm/trouble mode, use one LDM-32 and three LDM-E32s for a maximum of

56 alarm indicators, 56 trouble indicators, 16 status indicators and 64 optional control switch

inputs. Multiple sets of LDM-32s with LDM-E32 expanders increasethe systemannunciation

capabilities beyond 56 zones or points. This is possible by various settings of address

switches SW1 and SW2 on the LDM-32 (refer to Appendices). Each LDM-E32 is supplied

with a 26 conductor expander ribbon cable, 4 standoffs and 4 screws.

Figure 2-2: LDM-E32

Ribbon Cable

Connectionsto

Next LDM-E32

Ribbon Cable

ConnectionFrom

Previous LDM-32 or

LDM-E32

OutputConnectors

for Wiring to LEDs

Security Key

SwitchTerminal

Terminal Formax.

of 16 External

Control Switches

Alarm Only or

Alarm/Trouble

Select Switch

Relay Power Ribbon

CableConnection

www.PDF-Zoo.com

815885 Rev. F1 8/2/95 P/N 15885:F1

2.3 Connectors on the LDM-32 and LDM-E32

J1 - Switch Matrix

Up to 16 optional external control switches and a local lamp test switch may be attached

to the LDM-32 and LDM-E32 via J1 as shown in Figure 4-10. To determine which switch

function each point will perform in a System 5000, refer to Appendix table A-1 (System

5000). Switch functions on an AM2020/AFP1010 are completely programmable.

J2 - Ribbon Cable Connection Between Master and Expander Modules to J3

A single 26 conductor ribbon cable may be connected from J2 on the LDM-32 or LDM-

E32 (see Figure 3-3) to J3 on adjacent LDM-E32s. The ribbon cable carries power,

ground and signaling from the LDM-32 to up to three LDM-E32s. The preformed cables

are supplied in fixed lengths of 24 and 48 inches.

J3 - Ribbon Cable Connection From J2

This connector supports a single 26 conductor ribbon cable from J2 of the previous

LDM-32 or LDM-E32. Refer to Figure 3-3.

J4 - Keyswitch Input

This two pin connector is provided as an input on LDM-32 and LDM-E32 modules for an

external security keyswitch. KeyswitchcontactsmustbeNormally Closed. The keyswitch

prevents unauthorized use of remote control switches wired to J1.

J5, J6, J7 and J8 - Lamp/LED Driver Outputs

Each connector provides 8 driver outputs for a total of 32 drivers on each LDM-32 and

LDM-E32. Each driver is rated for a maximum of 30 volts and a current of 100 mA. Each

bipolar Darlington open collector driver output must be current limited by an external

resistor. 8-Point Shift and Flash functions are selectable by DIP switch SW3 (refer to

Section 2.4). Lamp/LEDs may function in 'alarm only mode' or 'alarm/trouble mode' as

selected byswitch SW4. Use the charts and examples shown in Appendices A and B for

additional information.

J9 - Lamp Power/SystemTrouble

Connector J9 is located only on the LDM-32. J9 pin 1 provides 24 volts regulated power

to all lamps/LEDs used in a custom graphic annunciator. The current limit of J9 pin 1 is

dependent upon the current limits of the external power source being used. J9 pin 3 is

a driver output for system trouble indication only. J9 pin 2 connects to system common.

J10 - Relay Expander

Cables to the optional LDM-R32 Relay Expander Module which can be used to provide

up to 32 dry Form-A (normally open) contacts.

J11 - 5VDC Power

This connector is located only on the LDM-32. J11 pin 1 provides 5 volts regulated

power to all lamps/LEDs used in a custom graphic annunciator. The maximum current

available from this output is 300 mA. This current is sufficient to power the maximum

number of LEDs available with one LDM-32 and three LDM-E32s (from J5, J6, J7, J8

and one system trouble LED)

provided the current rating per LED is 2 mA.

www.PDF-Zoo.com

15885 Rev. F1 8/2/95 P/N 15885:F1 9

2.4 Switches

SW1 and SW2 - Address Switches

Two rotary BCD switches, located only on the LDM-32, are used to set the LDM Series

system address. Switch SW1 represents the 'ones' position and switch SW2 represents

the 'tens' position of the address setting. In system configurations of 56 zones or less,

the switches must be set to address 01 for all LDMs in the system. For configurations

larger than 56 zones, multiple sets of LDMs are required with sequential addresses, the

first LDM starting at address 01. Each incremental setting adds 64 zones/points to the

system.

SW3 - Function DIP Switch

SW3, which is located only on the LDM-32, is used to set the annunciator functions.

Function settings include:

• Number of expanders connected

• 8-Point Shift enabled

• Receive Only communications to host FACP (no system control switches or

loss of supervision)

• Receive/Transmit communications to host FACP (system control switches plus

supervision)

• Control Switch Disable

• Piezo disable

• Flash Inhibit

Refer to Appendices A and B for additional information.

SW4 - Alarm/Trouble Mode Switch

The Alarm/Trouble mode switch is installed on the LDM-32 and LDM-E32.

The switch

setting on each expander module must match the switch setting of the associated LDM-

32.

'Alarm Only' mode causes the driver outputs to turn on only for alarm conditions per

associatedzoneorpoint atthe hostFACP. Alarm/Trouble mode causes the driver outputs

to turn on for both alarm and trouble conditions per associated zone or point at the host

FACP. Since this switch affects the assignments of connectors J5, J6, J7 and J8, make

certain to review the appendices in this manual for additional information on wiring to the

lamp/LED drivers.

TB1 - Power, Earth Ground and Supervision

Removable terminal block TB1 appears only on the LDM-32. 24 volts power-limited,

regulated, non-resettable power from the host FACP or a compatible UL listed battery

backed power supply must be connected to TB1-3 (+) and TB1-5 (-). Terminals TB1-2

(+) and TB1-4 (-) may be used to daisy chain the 24 volts to other LDMs or devices.

Earth ground must be connected to TB1-1. Terminals TB1-6 and TB1-7 provide a

supervised input which may be used to supervise local power sources or other devices.

A trouble signal is transmitted to the host FACP upon an open circuit across these

terminals. The input must be power-limited. If these terminals are not used, a jumper

must be installed.

TB2- In/Out

Removable terminal blockTB2 appears only on the LDM-32. All LDM-32s must connect

to the EIA-485 communications bus circuit for proper operation. The EIA-485 bus carries

commands and data sent between the host FACP and the LDMs. The input must be

power-limited.

2.5Terminal Blocks

www.PDF-Zoo.com

10 15885 Rev. F1 8/2/95 P/N 15885:F1

2.6 Cables

Expander Ribbon Cable (75120)

TheExpander RibbonCableissupplied with theLDM-E32 toallow

for connection to the LDM-32 master module. The cable connects

between J2 of the LDM-32 or LDM-E32 and J3 of the next LDM-

E32.

The LDM-CBL24 and LDM-CBL48

Cable sets for connecting LDM-32 and LDM-E32 connectors to

lamps/LEDs,switches,etc., areprovidedthrough theoptionalLDM-

CBL24 (24" long) and LDM-CBL48 (48" long) cabling kits. Each

cable has a plug on one end for connection to the LDM modules.

• Each LDM-CBL24 cable kit includes:

✓(4) P/N 75116, 24" cable consisting of 8 stranded,

multicolored conductors. Cables connect to J5, J6, J7 and

J8.

✓(1) P/N 75122, 24" cable consisting of 10 stranded,

multicolored conductors. Connects to J1, optional control

switches.

✓(1) P/N 75117, 24" cable consisting of 2 stranded, single

color conductors. Connects to J1, Lamp Test Switch.

✓(1) P/N 75118, 24" cable consisting of 3 stranded,

multicolored conductors. Connects to J9 or J11, Lamp

Power.

• Each LDM-CBL48 cable kit includes:

✓(4) P/N 75147, 48" cable consisting of 8 stranded,

multicolored conductors. Cables connect to J5, J6, J7 and

J8.

✓(1) P/N 75150, 48" cable consisting of 10 stranded,

multicolored conductors. Connects to J1, optional control

switches.

✓(1) P/N 75148, 48" cable consisting of 2 stranded, single

color conductors. Connects to J1, Lamp Test Switch.

✓(1) P/N 75149, 48" cable consisting of 3 stranded,

multicolored conductors. Connects to J9 or J11, Lamp

Power.

• Keylock Control Switch Security:

A UL listed key-lock switch wired to J4 on the LDM-32 should

beusedto provideaccess security for allcontrolswitcheswired

to that set of LDM modules.

Control switches will not function

when the key-lock switch is in its closed position.

KEYSWITCH LDM-32

www.PDF-Zoo.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pittway Unité de contrôle

Pittway

Pittway SYSTEM SENSOR M500DM Manuel utilisateur

Pittway

Pittway System Sensor MOD400R Manuel utilisateur

Pittway

Pittway SYSTEM SENSOR M502M Manuel utilisateur

Pittway

Pittway SYSTEM SENSOR M500FP Manuel utilisateur

Pittway

Pittway System Sensor M500DR Manuel utilisateur

Pittway

Pittway System Sensor MB500 Manuel utilisateur

Pittway

Pittway Fire-Lite Alarms MMF-300 Manuel utilisateur

Pittway

Pittway NOTIFIER UZC-256 Manuel d'installation

Pittway

Pittway SYSTEM SENSOR M500M Manuel utilisateur

Pittway

Pittway NOTIFIER FCM Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur