Phoenix MicroATX Express Manuel utilisateur

Phoenix MicroATX Express

Motherboard

Installation Guide

StockCheck.com

Downloaded from StockCheck.com

Introduction

Table of Contents

Introduction ........................................................................................ IV

Chapter 1 Pre-Configuration ....................................................1

Step 1 Setting the Jumpers 2

Jumper Locations............................................................................................................................... 3

CMOS Reset ........................................................................................................................................ 4

ATA-Disk Connector Voltage Selection ...........................................................................................4

RS422/RS485 Termination Resistors (optional).............................................................................. 4

Step 2 SDRAM, CPU, and Cables Installation 4

Phoenix MicroATX Express Memory Configuration ....................................................................... 4

CPU Installation .................................................................................................................................. 5

Installing Cables............................................................................................................................... 10

Power and Control Panel Cables .................................................................................................... 10

Installing Peripheral Cables ............................................................................................................ 11

Index of Connectors......................................................................................................................... 14

Chapter 2 AMIBIOS8 Setup....................................................16

Main Setup ........................................................................................................................................ 19

Advanced BIOS Setup ..................................................................................................................... 19

PCI/PnP Setup................................................................................................................................... 25

Boot Setup ........................................................................................................................................ 27

Security Setup .................................................................................................................................. 30

Chipset Setup ................................................................................................................................... 32

Exit Menu........................................................................................................................................... 34

Chapter 3 Upgrading ..................................................................35

Upgrading the Microprocessor ....................................................................................................... 35

Upgrading the System Memory ...................................................................................................... 35

Appendix A Technical Specifications................................37

Chipsets ............................................................................................................................................ 37

BIOS................................................................................................................................................... 37

Embedded I/O ................................................................................................................................... 37

Industrial Devices............................................................................................................................. 38

Miscellaneous ................................................................................................................................... 39

Memory Map...................................................................................................................................... 40

DMA Channels .................................................................................................................................. 40

I/O Map............................................................................................................................................... 40

Interrupts........................................................................................................................................... 41

SMBUS............................................................................................................................................... 42

PCI Interrupt Routing Map............................................................................................................... 42

StockCheck.com

Downloaded from StockCheck.com

Phoenix MicroATX Express – Installation Guide

Connectors Pin-out .......................................................................................................................... 42

Appendix B Flash BIOS programming and codes .....48

Troubleshooting POST .................................................................................................................... 48

Critical Error BEEP Codes............................................................................................................... 52

Appendix C On-Board Industrial Devices.......................54

Post Code Display ............................................................................................................................ 54

On-board Ethernet............................................................................................................................ 54

Serial Ports........................................................................................................................................ 55

Appendix On-Board Video Controller ...............................60

StockCheck.com

Downloaded from StockCheck.com

Introduction

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information

contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any

subsequent vendor. They are in no way responsible for any loss or damage resulting from the use (or misuse) of this

publication.

This publication and any accompanying software may not, in whole or in part, be copied, photocopied, translated or

reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this

publication, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks

of their respective companies. They are mentioned for identification purposes only and are not intended as an

endorsement of that product or its manufacturer.

First Edition.

November 2006

III

StockCheck.com

Downloaded from StockCheck.com

Phoenix MicroATX Express – Installation Guide

Introduction

Thank you for your purchase of the Phoenix MicroATX Express industrial embedded motherboard. The Phoenix

MicroATX Express design was based on the Intel 945G chipset providing the ideal platform to industrial

applications. The Phoenix MicroATX Express design is based on the Intel Pentium 4 processor LGA775 socket

(FC-LGA4).

With proper installation and maintenance, your Phoenix MicroATX Express will provide years of high performance

and trouble free operation.

This manual provides a detailed explanation into the installation and use of the Phoenix MicroATX Express

industrial embedded motherboard. This manual is written for the novice PC user/installer. However, as with any

major computer component installation, previous experience is helpful and should you not have prior experience, it

would be prudent to have someone assist you in the installation. This manual is broken down into 3 chapters and 4

appendixes.

Chapter 1 - System Board Pre-Configuration

This chapter provides all the necessary information for installing the Phoenix MicroATX Express. Topics

discussed include: installing the CPU (if necessary), DRAM installation and jumper settings. Connecting

all the cables from the system board to the chassis and peripherals is also explained.

Chapter 2 - BIOS Configuration

This chapter shows the final step in getting your system firmware setup.

Chapter 3 - Upgrading

The Phoenix MicroATX Express provides a number of expansion options including memory. All aspects of

the upgrade possibilities are covered.

Appendix A - Technical Specifications

A complete listing of all the major technical specifications of the Phoenix MicroATX Express is provided.

Appendix B - Flash BIOS Programming and Codes

Provides all information necessary to program your AMIBIOS8 Flash BIOS. POST Codes and beep codes

are described in details.

Appendix C – On-Board Industrial Devices

One or Two on-board Gigabit Ethernet controller(s), two or six serial ports (one optional RS422/485),

hardware monitor, watchdog timer and Post Code Display.

Appendix D - On-Board Video Controller

On-board CRT video controller.

StockCheck.com

Downloaded from StockCheck.com

Introduction

Static Electricity Warning!

The Phoenix MicroATX Express has been designed as rugged as possible but can still be damaged if jarred sharply

or struck. Handle the motherboard with care.

The Phoenix MicroATX Express also contains delicate electronic circuits that can be damaged or weakened by

static electricity. Before removing the Phoenix MicroATX Express from its protective packaging, it is strongly

recommended that you use a grounding wrist strap. The grounding strap will safely discharge any static electricity

build up in your body and will avoid damaging the motherboard. Do not walk across a carpet or linoleum floor with

the bare board in hand.

Warranty

This product is warranted against material and manufacturing defects for two years from the date of delivery. Buyer

agrees that if this product proves defective the manufacturer is only obligated to repair, replace or refund the

purchase price of this product at manufacturer's discretion. The warranty is void if the product has been subjected to

alteration, misuse or abuse; if any repairs have been attempted by anyone other than the manufacturer; or if failure is

caused by accident, acts of God, or other causes beyond the manufacturer's control.

Phoenix MicroATX Express - An Overview

The Phoenix MicroATX Express represents the ultimate in industrial embedded motherboard technology. No other

system board available today provides such impressive list of features:

CPU Support

• Supports Intel Pentium 4, Intel Pentium D and Intel Celeron D processors in the LGA775 socket with a

1066, 800 and 566MHz system bus.

Supported Bus Clocks

• 1066, 800 and 566MHz.

Memory

• Four 240-pin DDR2 SDRAM module sockets up to 4GB (non-ECC), DDR2 667, DDR2 533, or DDR2 400

MHz SDRAM DIMMs. Please, refer to chapter 3 for memory details.

On-Board I/O

• 2 Floppies up to 2.88 MB.

• Single channel PCI 32-bit EIDE controller – UDMA 66/100 supported. One standard 40-pin header and

one mini-Header 44-pin for Solid State IDE disk or any 44-pin IDE device support shared on the single primary

channel.

• Four independent Serial ATA2 ports with transfer rates up to 300 MB/s per port.

• Two or optional six high speed RS-232 serial ports 16 Bytes FIFO (16550). COM2 RS-232 IrDA on a

header and COM1 optional RS-422/485.

• One bi-directional parallel port. EPP/ECP mode compatible.

• One PS/2 mouse and one PS/2 keyboard.

StockCheck.com

Downloaded from StockCheck.com

Phoenix MicroATX Express – Installation Guide

• Eight Universal Serial Bus ports, USB 1.1 and USB 2.0 compliant. Four connectors and four headers

• Two 32-bit PCI slots, one PCI Express x16 dedicated graphics slot and one PCI Express x4 slot.

• One (optional two) PCI Express based Gigabit Ethernet controllers.

• Automatic CPU voltage & temperature monitoring device.

• On-board Buzzer.

• Intel HD Audio. Microphone In, Stereo Line In and Out, Aux In and CD In.

ROM BIOS

• American Megatrends AMIBIOS8 with FLASH ROM.

On-Board CRT video controller

• Standard CRT video controller (Intel 945G chipset).

Conventions Used in this Manual



Notes - Such as a brief discussion of memory types.

Important Information - such as static warnings, o

very important instructions.

When instructed to enter keyboard keystrokes, the

text will be noted by this graphic.



StockCheck.com

Downloaded from StockCheck.com

Chapter 1: Pre-Configuration

Chapter 1 Pre-Configuration

This chapter provides all the necessary information for installing the Phoenix MicroATX Express into a standard PC

chassis. Topics discussed include: installing the CPU (if necessary), DRAM installation and jumper settings.

Handling Precautions

The Phoenix MicroATX Express has been designed to be as rugged as possible but it can be damaged if dropped,

jarred sharply or struck. Damage may also occur by using excessive force in performing certain installation

procedures such as forcing the system board into the chassis or placing too much torque on a mounting screw.

Take special care when installing or removing the system memory DIMMs. Never force a DIMM into a socket.

Screwdrivers slipping off a screw and scraping the board can break a trace or component leads, rendering the board

unusable. Always handle the Phoenix MicroATX Express with care.

Special Warranty Note:

Products returned for warranty repair will be

inspected for damage caused by imprope

installation and misuse as described in the

revious section and the static warning below.

Should the board show signs of abuse, the

warranty will become void and the customer wil

be billed for all repairs and shipping an

handling costs.

Static Warning

The Phoenix MicroATX Express contains delicate electronic semiconductors that are highly sensitive to static

electricity. These components, if subjected to a static electricity discharge, can be weakened thereby reducing the

serviceable life of the system board. BEFORE THE BOARD IS REMOVED FROM ITS PROTECTIVE

ANTISTATIC PACKAGING, TAKE PROPER PRECAUTIONS! Work on a conductive surface that is connected

to the ground. Before touching any electronic device, ground yourself by touching an unpainted metal object or, and

highly recommended, use a grounding strap.

StockCheck.com

Downloaded from StockCheck.com

Phoenix MicroATX Express – Installation Guide

Step 1 Setting the Jumpers

Your Phoenix MicroATX Express is equipped with a large number of peripherals. As such, there are a large number

of configuration jumpers on the board. Taken step by step, setting these jumpers is easy. We suggest you review

each section and follow the instructions.



Special note about operating frequency:

The Phoenix MicroATX Express has the ability to

run at a variety of speeds without the need to

change any crystal, oscillator or jumper.

Jumper Types

Jumpers are small copper pins attached to the system board. Covering two pins with a shunt closes the connection

between them. The Phoenix MicroATX Express examines these jumpers to determine specific configuration

information. There are two different categories of jumpers on the Phoenix MicroATX Express.

A. Two pin jumpers are used for binary selections such as enable, disable. Instructions for this type of jumper are

open, for no shunt over the pins or closed, when the shunt covers the pins.

B. Three or four pin jumpers are used for multiple selections. Instructions for these jumpers will indicate which two

pins to cover. For example: for JPx2-3 the shunt will be covering pins 2 and 3 leaving pins 1 and 4 exposed.

How to identify pin number 1 on Figure 1-1: Looking to the solder side (The board side with fewer components) of

the PCB (Printed Circuit Board), pin number 1 will have a squared pad J. Other pins will have a circular pad Q.

They are numbered sequentially.

Double row jumpers are numbered alternately, i.e. pin number 2 is in the other row, but in the same column of pin

number 1. Pin number 3 is in the same row of pin 1, but in the next column and so forth.

StockCheck.com

Downloaded from StockCheck.com

Table des matières

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur