Phoenix Model LASER Manuel utilisateur

Table des matières

Autres manuels Phoenix Model Jouet

Phoenix Model

Phoenix Model Tiger Moth Manuel

Phoenix Model

Phoenix Model PC21 PILATUS Manuel utilisateur

Phoenix Model

Phoenix Model K8B Manuel utilisateur

Phoenix Model

Phoenix Model strega Manuel utilisateur

Phoenix Model

Phoenix Model BAZOOKA Manuel utilisateur

Phoenix Model

Phoenix Model Dolphin 40 Manuel utilisateur

Phoenix Model

Phoenix Model Cap 232 Manuel utilisateur

Phoenix Model

Phoenix Model LA9 Manuel utilisateur

Phoenix Model

Phoenix Model SENTOSA Manuel utilisateur

Phoenix Model

Phoenix Model PH 165-OUTRAGEOUS Manuel utilisateur

Phoenix Model

Phoenix Model CESSNA AWAGON Manuel utilisateur

Phoenix Model

Phoenix Model Classic Manuel utilisateur

Phoenix Model

Phoenix Model Ryan STA Manuel utilisateur

Phoenix Model

Phoenix Model Dolphin Manuel utilisateur

Phoenix Model

Phoenix Model westland lysander Manuel utilisateur

Phoenix Model

Phoenix Model MXS Manuel utilisateur

Phoenix Model

Phoenix Model Diabolo Manuel utilisateur

Phoenix Model

Phoenix Model WACO F5C Manuel utilisateur

Phoenix Model

Phoenix Model PA-18 Super Cub Manuel utilisateur

Phoenix Model

Phoenix Model Tiger 3 Manuel utilisateur

Phoenix Model

Phoenix Model KATANA-61 Manuel utilisateur

Phoenix Model

Phoenix Model Tiger Moth Manuel utilisateur

Phoenix Model

Phoenix Model decathlon - EP Manuel utilisateur

Phoenix Model

Phoenix Model GENESIS Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard

KIT CONTENTS: We have organized the parts as they come out of the box for better

identification during assembly. We recommend that you regroup the parts in the same

manner. This will ensure you have all of parts required before you begin assembly

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons

• (1) Fuselage with canopy

• (1) Horizontal stabilizer with elevator halves

• (1) Vertical stabilizer with rudder

• (1) Fiberglass cowling

• (1) Belly Pan

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nut

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axle

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire

• (1) 25mm diameter wheel

• (1) Wheel collar

• (1) 3mm x 4mm set screw

• (2) control clasp

• (4) 2mm x 10mm nut

ELEVATOR CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

RUDDER CONTROL SYSTEM

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screws

• (1) Metal clevis

• (1) Metal pushrod

AILERON CONTROL SYSTEM

• (2) 2mm x 260mm threaded wires

• (2) Nylon snap keepers

• (2) Nylon control horn w/plates

• (4) 2mm x 20mm screws

• (2) Metal clevis

MOTOR MOUNT ASSEMBLY

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screws

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire

• (1) 3,5mm x 350mm nylon pushrod housing

• (1) Metal connector

• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel Tank

• (1) Metal clunk

• (1) Silicone tube / 110mm

• (1) Pre - assembled stopper w / 3 tube

• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Wood dihedral brace

• (1) 25mm x 600mm trim tape (white)

• (1) Plywood

• (4) 2.6mm x 10mm wood screws

• (1) Decal sheet.

• (1) Block of wood (white)

• (1) Decal sheet 50mm x 100mm

• (4) 3mm x 40mm screws

• (4) 8mm washers

• (1) Plywood washer

ADDITIONAL ITEMS REQUIRED

• 40-50 two stroke Engine.

• 70 four stroke Engine.

• 4 channel Radio with 5 servos.

• Glow plug to suit Engine.

• Propeller to suit Engine.

• Protective foam Rubber.

• Silicone fuel line.

• Stick on weight for balance.

KIT CONTENTS

Instruction Manual Laser

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your

plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

140mm BACK FROM THE LEADING EDGE

OF THE WING, AT THE FUSELAGE. This

location is recommended for initial test flying

and trimming. There is a 10mm margin forward

and aft. BALANCE A PLANE UPSIDE DOWN

WITH THE FUEL TANK EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the

top side of the wing 140mm back from the

leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift

the plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery

pack further back in the fuselage. If this is not

possible or does not correct it, stick small

amounts of lead weight on the fuselage under

the horizontal stabilizer. If the tail of the plane

falls, the plane is tail heavy. To correct this,

move the battery and receiver forward or if this

is not possible, stick weight into the firewall.

When balanced correctly, the airplane should

sit level or slightly nose down when you lift it

up with your fingers

LATERAL BALANCE

After you have balanced a plane on the C.G. You

should laterally balance it. Doing this will help the

airplane track straighter.

1. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to

the tail wheel wire. With the wings level, carefully

lift the airplane by the string. This may require two

people to make it easier.

2. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to

the bottom side of the lighter wing half's wing tip.

Follow this procedure until the wing stays level

when you lift the airplane

140mm

FLIGHT PREPARATION

PRE FLIGHT CHECK

1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your

plane to ensure that everything is tight and well

bonded.

3. Double check the balance of the airplane

4. Check the control surface

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

We wish you many enjoyable flights with

your plane and once again thank you for

your choosing a Phoenix Model's product.

Ailerons : 10mm up 10mm down

Elevator : 12mm up 12mm down

Rudder : 60mm right 60mm left

CONTROL THROWS

1. We highly recommend setting up a plane using

the control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in

the correct directions.

Elevator Control

Aileron Control

10mm

Rudder Control

60mm

12mm

Instruction Manual Laser

TOOLS AND SUPPLIES NEEDED

• Medium C/A glue.

• 30 minute epoxy.

• 6 minute epoxy.

• Hand or electric drill.

• Assorted drill bits.

• Modeling knife.

• Straight edge ruler.

• 2 bender plier.

• Wire cutters.

• Masking tape.

• Thread lock.

• Paper towels.

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old towel or

brown paper, both to protect the aircraft and to

protect the table. Keep a couple of jars or bowls

handy to hold the small parts after you open the bag.

NOTE

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned

properly before gluing! This will assure proper

assembly. The LASER ARF is hand made from

natural materials, every plane is unique and minor

adjustments may have to be made. However, you

should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone.

Do not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the

propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the

propeller only. Do not reach around the spinning

propeller.

3. Using a modeling knife, remove the covering

from over the pre-cut servo box as shown.

INSTALL CA HINGES FOR

AILERON-ELEVATOR-RUDDER

Make sure the control surfaces will deflect to the

recommended throws without binding.If you have

to cut your hinge slots too far ,leaving only a small

portion of the hinge in the control surface .To avoid

this ,you may insert a small pin through the center

of each hinge before installing . This pin will keep

the hinge centered while you control surfaces.

Apply 6 drops of thin CA adhesive to both sides of

each hinge. Allow a few seconds between drops

for the CA to wick into the slot.

WING ASSEMBLY

PARTS REQUIRED

• (2) Wing halves with ailerons.

• (1) Dihedral brace.

• (1) White self adhesive Trim Tape.

• (1) Gray self adhesive Trim Tape.

INSTALLING THE AILERONSERVO

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over

the precut servo lead exit hole on the top of the

wing sheeting. This hole will allow the servo

leads to pass through when the wing halves are

joined.

Remove the

covering

Picture 1

Instruction Manual Laser

4. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the slot in

the mounting platform and to the vertical

stabilizer mounting area. Apply epoxy to the

lower rudder hinge. Set the stabilizer in place

and re-align. Double check all of your

measurements once more before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Allow the epoxy to fully cure before proceeding.

3. Slide the vertical stabilizer back in place. Using

a triangle, check to ensure that the vertical

stabilizer is aligned 90 degree to the horizontal

stabilizer.

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the stabilizer

in place and carefully inspect the glue joints. Use

more epoxy to fill in any gaps that were not filled

previously and clean up the excess using a

paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.

1. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark

the shape of the fuselage on the left and right

sides of the vertical stabilizer using a felt-tip pen.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) Nylonl clasps

· (4) 2mm x 12mm wood screws.

1. Install two nylon clasp to the rudder and using

two 2mmX12mm srew, screw it as shown.

2. Install wheel into the tail landing.

Slide the tail wheel wire through the two nylon clasp.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. Set the tail wheel

assembly in place on the plywood plate.

5. Drill 1.5mm pilot holes through the plywood

plate. Secure the tail wheel bracket in place

using three 2mm x12mm screw.

Remove the covering

Picture 17

2. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the

marked lines and remove the film on both sides

of the vertical stabilizer. Just as you did with the

horizontal stabilizer, make sure you only press

hard enough to cut the film, not the balsa

vertical stabilizer.

Picture 18

Remove the covering

Picture 19

Screw

clasps

Picture 21

Glue the hinge Insert the hinge

Picture 20

Instruction Manual Laser

Screw the servo into the servo box as shown.

4. Using the thread (Not included in the kit) as a

guide and using masking tape, tape the servo

lead to the end of the thread: carefully pull the

thread out. When you have pulled the servo

lead out, remove the masking tape and the

servo lead from the thread.

INSTALLING THE DIHEDRAL BRACE

1. Look carefully at the surface of each root rib on

both wing halves. Notice how the excess

covering material overlaps onto them. Using a

modeling knife, carefully cut out away the

covering from both root ribs. Iron the covering

down so that it does not pull away from the ribs.

It is important that the excess covering be

removed from the root ribs. This will ensure an

adequate wood to wood glue joint.

2. Using a ruler and a pen, locate and mark the

center line of the dihedral brace. Draw the vertical

line at this location on each side of the brace.

3. Test fit the dihedral brace into the box in each

wing half. The brace should slide into each

wing half up to the center line. If it does not,

remove the brace and lightly sand the edges

and tips until the proper fit is obtained.

4. Test fit both of the wing halves together with the

dihedral brace temporarily installed. Do not

glue it in at this time! The wing halves should fit

together tight with little or no gaps in the center

section joint. If the center section joint is not

tight, remove the wing halves and lightly sand

the edges and tips of the dihedral brace. Test fit

the wing halves together with the dihedral

brace installed again. Repeat until you are

satisfied with the fit of the wing halves. The

proper dihedral is built into the two root ribs and

should not be altered.

5. When satisfied with the fit of the wing halves,

remove the wing halves and the dihedral brace.

JOINING THE WING HALVES

1. Mix a generous amount of 30 minute epoxy.

Working with only one wing half for now, apply

a thin layer of epoxy inside the dihedral brace

box and to only half of the dihedral brace. Make

sure to cover the dihedral brace top and bottom

as well as the sides, and use enough epoxy to

fill any gaps.

2. Slide the dihedral brace into the box up to the

center line. Remove any excess epoxy before it

dries using a paper towel and rubbing alcohol.

Allow the epoxy to cure before proceeding.

Picture 3

Masking Tape

Picture 6

Picture 7

Servo lead

Picture 4

Instruction Manual Laser

Remove the

covering

180 mm

105 mm

Picture 2

5. Repeat step # 2 - # 5 to install the second

aileron servo in the opposite wing half.

6. Using masking tape, tape the servo leads on to

the top of the wing.

Draw a center Line

Thread

3. Once the epoxy has cured, trial fit both wing

halves together to double check that the wing

halves still fit correctly.

4. Mix a generous amount of 30 minute epoxy. Apply

a thin layer of epoxy to the exposed half of the

dihedral brace, the inside of the dihedral brace

box and the entire surface of both root ribs. Make

sure to use enough epoxy to fill any gaps.

5. Slide the two wing halves together and carefully

align them at the leading and trailing edges. Wipe

away any excess epoxy using a paper towel and

rubbing alcohol. Use masking tape to hold the

two wing halves in place until the epoxy cures.

6. When the epoxy has fully cured, double check the

center section joint. If any gaps are present, mix a

small amount of 30 minute epoxy and carefully fill

any remaining gaps. Remove the excess epoxy

using a paper towel and rubbing alcohol. Allow

the epoxy to fully cure before proceeding.

7. Apply the trim tape to the center section of the

wings where they join.

AILERON LINKAGE

PARTS REQUIRED

· (2) 2mm x 260mm Thread wires.

· (2) Nylon control horns.

· (2) Metal clevis.

· (2) Mounting snap keepers

· (4) 2mm x 20mm machine screws.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and mark

the location of the control horn. It should be

mounted on the bottom side of the aileron at the

leading edge, in line with the aileron pushrod.

2. Drill two 2mm holes through the aileron using

the control horn as a guide and screw the

control horn in place.

Picture 8

Trim tape

Picture 9

RIGHT WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now, thread

one nylon clevis at least 14 turns onto one of

the 2mm x 260mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis

3. Locate one nylon servo arm, and using wire

cutters,remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center of the arm to accommodate the aileron

pushrod wire.

4. Plug the aileron servo into the receiver and center

the servo. Install the servo arm onto the servo.

The servo arm should be perpendicular to the

servo and point toward the middle of the wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod

wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess

wire, leaving about 4mm beyond the bend.

Aileron servo

Picture 10

Instruction Manual Laser

Aileron pushrod

Clevis

Picture 11

Control horn

Nylon snapkeeper

Control horn

In line

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

8. Insert the 90 degree bend down through the

hole in the servo arm. Install one nylon snap

keeper over the wire to secure it to the arm.

Install the servo arm retaining screw and

remove the masking tape from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed,

connect both of the aileron servo leads using a

Y-harness you have purchased separately.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and

centered to the fuselage by taking measurements,

but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and

bottom of the tail plane using a water soluble /

non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering

from between them using a modeling knife.

When cutting through the covering to remove it,

cut with only enough pressure to only cut

through the covering it's self. Cutting into the

balsa structure may weaken it. This could lead

to possible failure during flight.

2. Using a modeling knife, cut away the covering

from the fuselage for the vertical and remove it.

90o

AA-1

A=A-1

Remove the covering

Picture 12

Picture 14

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30

minute epoxy. Apply a thin layer to the top and

bottom of the stabilizer mounting area and to

the stabilizer mounting platform sides in the

fuselage. Slide the stabilizer in place and

re-align. Double check all of your

measurements one more time before the epoxy

cures. Remove any excess epoxy using a

paper towel and rubbing alcohol and hold the

stabilizer in place with T-pins or masking tape.

Remove the covering

Picture 15

Glue with epoxy

Picture 16

Instruction Manual Laser

Picture 13

Center line

INSTALLING THE engine mount

1. Install the engine mount into the firewall as shown

INSTALLING THE throttle pushrod housing

1. Place the engine into the engine mount and

align it properly with the front of the cowling.

The distance from the firewall to the front of the

engine thrust washer should [105mm]

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at

this time.

2. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole

location onto the firewall, where the throttle

pushrod will exit.

3. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward

bulkhead at the marks made.

4. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward

bulkhead, and into the servo compartment.

5. Apply a couple of drops of thin C/A to the

pushrod housing where it exits the firewall and

where it passes through the forward bulkhead.

This will secure the housing in place.

6. Using a modeling knife, cut off the nylon pushrod

housing 26mm in front of the servo tray.

Picture 26

Picture 27

INSTALLING THE ENGINE

Locate the long piece of wire used for the throttle

pushrod. One end of the wire has been pre-bend in

to a "Z" bend at the factory. This "Z" bend should be

inserted into the throttle arm of the engine when the

engine is fitted onto the engine mount. Fit the engine

to the engine mount using the screws provided.

FUEL TANK

PARTS REQUIRED

· (1) Nylon fuel tank.

· (1) Metal clunk.

· (1) Silicon tube.

· (1) Pre-assemble stopper.

· (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the

stopper.

3. Carefully bend the second nylon tube up at a

45 degree angle (using a cigarette lighter). This

tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a

45 degree angle (using a cigarette lighter). This

tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

20right thrust00down thrust

Picture 28

Instruction Manual Laser

In the case the engine is not fit with the engine

mount - sand the engine mount as shown.

Sand

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the

flashing around the tank opening using a

modeling knife. If flashing is present, make sure

none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine

screw until the rubber stopper expands and

seals the tank opening. Do not over tighten the

assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes

and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in

the firewall. Pull the lines out from behind the

engine, while guiding the fuel tank into place.

Push the fuel tank as far forward as possible,

the front of the tank should just about touch the

back of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel

tank compartment. Air should flow through easily.

9. Using the foam and a pice of wood to secure the

fuel tank as shown.

SERVO INSTALLATIONINSTALLING THE SERVO

1. Install the rubber grommets and brass collets

into the elevator, rudder, and throttle servos.

Test fit the servos into the servo tray

2. Mount the servos to the tray using the mounting

screws provided with your radio system.

Elevator servo

Rudder servo

Throttle servo

To carburator

To muffler

To vent Tube Picture 30

Picture 31

Picture 32

Picture 33

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm x 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Picture 29

Foam

Wood

Remove the covering

1. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the

bottom, left side of the elevator at the leading

edge, in line with the elevator pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tub e on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the elevator pushrod wire.

6. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator

pushrod wire where it crosses the hole in the

servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

1. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

2. The control horn should be mounted on the left

side of the rudder at the leading edge, in line

with the rudder pushrod.

3. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the

control horn in place.

4. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

5. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a

2mm drill bit, enlarge the third hole out from the

center to accommodate the rudder pushrod wire.

6. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the

servo. The servo arm should be perpendicular

to the servo and point toward the middle of the

fuselage.

7. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod

wire where it crosses the hole in the servo arm.

8. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,

leaving about 8mm beyond the bend.

9. Insert the 90 degree bend up through the hole

in the servo arm, install one nylon snap keeper

over the wire to secure it to the arm. Install the

servo arm retaining screw and remove the

masking tape the elevator halves.

Clevis

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through

the third hole out from the center of one servo

arm, enlarge the hole in the servo arm using a

2mm drill bit to accommodate the servo

connector. Remove the excess material from

the arm.

Clevis

Elevator servo

Rudder servo

Picture 34 Picture 35

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

• (1) Nylon snap keeper

• (1) Nylon control horn w/plate

• (2) 2mm X 20mm screw

• (1) Metal clevis

• (1) Metal pushrod

Instruction Manual Laser

Pushrod

ALIGNING THE BELLY PAN

1. With the wing securely attached to the fuselage,

trial fit the belly pan to the bottom of the wing.

The sides of the belly pan, at both the front and

the rear, should be flush with the sides of the

fuselage.

2. When satisfied with the fit, hold the belly pan in

place on the wing using pieces of masking tape.

3. With the belly pan hold firmly in place and

aligned properly, use a felt tip pen and outline

the belly pan onto the wing surface on the two

outside edges of the belly pan.

4. Remove the belly pan. Using the lines as a

guide, use a modeling knife and carefully

remove the covering from just inside the edge

of each line. Be careful not to cut in to the balsa

under the covering.

5. Glue the plywood plate onto the bottom of the

wing as show.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron

extension into the receiver to make plugging in

the aileron servo lead easier when you are

installing the wing. Plug the battery pack lead

into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.

Use a rubber band or masking tape to hold the

foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,

placed over the battery and receiver and glue

to the fuselage sides to hold the battery and

receiver securely in place. Use 15mm triangle

pieces glued between the fuselage sides and

the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the

antenna to exit.

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage

side, opposite the muffler, close enough to the

receiver so the lead will reach. Use the face

plate of the switch cut out and locate the

mounting holes.

2. Cut out the switch hole using a modeling knife.

Use a 2mm drill bit and drill out the two

mounting holes through the fuselage side.

3. Secure the switch in place using the two

machine screws provided with the radio system

Peel off the covering

Picture 40

Glue with epoxy

Picture 34

Picture 41

Instruction Manual Laser

Plywood plate

INSTALLING THE BELLY PAN

1. Remove the covering from the rear of the belly pan.

2. Mix up a generous amount of 30 minute epoxy.

Apply a thin layer of epoxy to the bottom edges

of the belly pan. Carefully set the belly pan back

in place on the wing and align it as you did

previously. Remove any excess epoxy using a

paper towel and rubbing alcohol.

3. Hold the belly pan firmly in place using strips of

masking tape along the entire gluing surface.

Allow the epoxy to fully cure before you remove

the masking tape.

Be carefully not to get any epoxy between the

wing and the fuselage.

Picture 39

Remove the covering

Switch

Receiver

!!!

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.

This will prevent the connector from loosening

during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the

throttle servo output shaft is moving in the

correct direction. When the throttle stick is

moved forward from idle to full throttle, the

throttle barrel should also open and close using

this motion. If not, reverse the direction of the

servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod

wire. Position the throttle stick and the throttle

trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from

center and attach the servo arm onto the servo.

With the carburator barrel fully closed, tighte

the set screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

4. While holding the cowl firmly in position, drill

four 1,6mm pilot holes through both the cowl

and the side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will

prevent the fiberglass from splitting when the

mounting screws are installed.

6. Slide the cowl back over the engine and secure

it in place using four 4mm x 16mm wood

screws.

7. Install the muffler. Connect the fuel and

pressure lines to the carburator, muffler and

fuel filler valve. Tighten the screws completely.

MOUNTING THE COWL

PARTS REQUIRED

· (1) Fiberglass cowl

· (4) 2.6mm x 10mm screws

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over

the engine.

2. Measure and mark the locations to be cut out

for engine head clearance, needle valve,

muffler,. Remove the cowl and make these

cutouts using a rotary tool with a cutting disc

and a rotary sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in the middle of the precut

opening. Hold the cowl firmly in place using

several pieces of masking tape.

Throttlle wire

Throttle servo

WING MOUNTING

PARTS REQUIRED

· (1) Belly pan

· (2) 4mm x 40mm screws

INSTALLING THE WING

1. Using a modeling knife, remove the covering

from the slot in the forward bulkhead.

2. Remove the covering from over the holes on

both the top and the bottom of the wing.

3. Place the wing into the wing saddle to check

the fit. Temporarily secure the wing in place

using the two 4mm x 40mm screws.

Do not over tighten the screws.

Picture 36

Picture 37

Picture 38

Instruction Manual Laser

Metal connector

(Use threadlock)

Tight

Loose

Tight

Throttle

I/C FLIGHT GUIDELINES

Made in Vietnam

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions. ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver. ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage. If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

Metric Conversions

Inches x 25.4 = mm (conversion factor)

1/64" = .4 mm 3/16" = 4.8 mm 1" = 25.4 mm 21" = 533.4 mm

1/32" = .8 mm 1/4" = 6.4 mm 2" = 50.8 mm 24" = 609.6 mm

1/16" = 1.6 mm 3/8" = 9.5 mm 3" = 76.2 mm 30" = 762.0

3/32" = 2.4 mm 1/2" = 12.7 mm 6" = 152.4 mm 36" = 914.4 mm

1/8" = 3.2 mm 5/8" = 15.9 mm 12" = 304.8 mm

5/32" = 4.0 mm 3/4" = 19.0 mm 18" = 457.2 mm

Instruction Manual Laser

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

1. Mark the holes for the axles on both sides of

one wheel pant 10mm up from the bottom edge

and centered in the wheel opening. Drill 5mm

holes at the marks.

2. Cut the wheel pant at one of the holes to make

a slot. When cutting the other wheel pant later,

be certain to cut on the other side so there will

be a right and a left wheel pant.

4. Fit the assembly into the wheel pant. Use thread

lock and another nut to tighten the axle and the

wheel pant to the landing gear. Tighten the

collars.

5. Mount the other wheel pant and wheel to the

other landing gear the same way. Be certain to

make a right and a left.

3. Prepare a wheel assembly with an axle,

washer, nut, collar wheel and another collar.

MAIN GEAR INSTALLATION

PARTS REQUIRED

• (2) Main gear Aluminum

• (2) 60mm diameter wheels

• (2) Fiberglass wheel pants

• (4) 3mm x 10mm machine screws

• (4) 3mm lock washers

• (2) 16mm flat washers

• (4) 4.5mm nuts

• (4) Wheel collars

• (4) 3mm x 6mm set screws

• (2) 4mm x 55mm axles

ENGINE INSTALLATION

PARTS REQUIRED

• (1) Motor mount

• (4) 4mm x 20mm machine screws

• (4) 4mm x 30mm machine screw

• (8) 4mm lock washer

• (8) 4mm nut

• (4) 4mm blind nut

• (2) Metal plate

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using

(4) 3mm x 10mm machine screws and 3mm

lock washers provided in the kit.

Picture 25

Instruction Manual Laser

Landing gearLanding gear ScrewScrew

Picture 22

Centered

10mm

5mm dia

Picture 23

INSTALLING THE WHEEL PANTS

Picture 24

Collar

Nut Washer

Instruction Manual

Wingspan:

1280mm (50.4 inches)

Length:

1390mm (54.7 inches)

Wing area:

34.7dm

(538 sp.in.)

Weight: 2800gr

Engine:

2C-40-50 / 4C-50-70

Radio : 4 channels

Servos : 5 standard