Philips InteGrade LED engine system Manuel utilisateur

Quick installation guide

Philips InteGrade LED engine system

for indoor environments and

refrigerated cabinets (-30 to +30 °C / -22 to +86 °F)

June 2013

Please take the time to read this installation guide before you install this Philips LED product and driver.

The guide contains important information regarding installation and operation.

Warranty

Warranty only applies when the appropriate Philips LED driver and Philips cabling (as described in this guide and leaets) are used.

Please visit our website www.philips.com/ledrefrigeration or contact your local sales ofce for more information.

Warnings

• The installation guide does not supersede local or (inter)national regulations for electrical installations.

• This Philips LED product and LED driver must be installed by a professional electrician in accordance with the applicable and

appropriate electrical codes and the instructions provided by Philips.

• Please note that the driver should be built into an enclosure (Tcase max. 70 °C / 158 °F).

• This Philips LED product is designed to be connected to a circuit from a class 2 power source (Philips Xitanium LED power driver)

with energy-limited supply.

• This is a 24 V DC product.

• Do not connect this LED product to mains voltages.

• To allow for variance in the installation, it is not recommended to load the power driver beyond 90% of its rated maximum power.

The energy consumption of the engine is a nominal value, with an estimated 20% deviation.

• Before installation, maintenance or cleaning, always rst switch off or disconnect the power and follow the appropriate safety

procedures.

• Before removing any lens covers or uorescent lamps, always rst switch off or disconnect the mains power to the lighting system.

• Take care not to damage the existing (heating) wiring if the LED product is installed in a freezer.

• Do not use tape to x this InteGrade LED product or LED prole in position; please use the appropriate mounting clips.

• Please note that the colors of the wires in existing designs, such as refrigeration systems or cabinets, may differ.The position of the

(original) ballast may also differ.

• Do not make sharp bends with electrical wires.

• Due to the variety of designs and brands in which the Philips LED products can be installed, you may need to use customized mounting

accessories to t the specic design you are using. If you require further support, please contact your local Philips sales organization.

• To prevent unwanted tripping caused by the inrush current of the LED driver, an MCB (mini circuit breaker) / fuse (slow blow) of

at least 6 A must be installed.

• Philips advises using a zero-crossing/switching solid-state relay to reduce the inrush current peak.

• This product is designed for damp and dry locations only.

Cleaning

• Use a damp cloth and a mild cleaning agent. Do not wipe the LED product with a dirty or very wet dishcloth or towel

because they may leave residue that can damage the LED product.

• Do not use abrasive cleaners, scouring pads, bleach or cleaners containing chlorine because they can scratch and damage

the LED product.

Important

www.philips.com/ledrefrigeration

Installation instructions

Philips Xitanium

LED Power Driver

(20 or 80 W 24 Vdc)

LED Power Driver 75 W-24 V PP ltG

-C8 plug

-N plug

RH<90%

InteGrade

cable angle

InteGrade

cable

InteGrade LED

engine

InteGrade

profile

InteGrade

profile (M style)

InteGrade

profile (F style)

InteGrade

connector

InteGrade engine

lock inline

InteGrade

mounting clip shelf arm

InteGrade

extension cable

InteGrade

Y cable

InteGrade

spacer cable

InteGrade

mounting clip under shelf

InteGrade magnet

for M style profile

RH<90%

2.9 mm (1/8 inch) Phillips H0 screw driver

Products and tools

OFF

Start

Phillips HO

screwdriver/

torque 10

to 15 cNm

Connecting the LED InteGrade engines

in the prole

50 cm (20 inch)

Installation examples with various

InteGrade mounting clips and proles

min. 2

RH<90%

When using the 2 m (79 inch) F style profile please ensure

it is properly fastened. Engines can then be placed in infinite

lines BUT should be powered in accordance with the

instructions in this guide. Each powered section should be

locked in place by two "lock in-line's" to ensure proper

contacting of the engines and power cables.

Never attach separate profiles

beneath individual

connected engines.

Attach a single profile beneath

two connected engines

in order to ensure

stability.

Tcase max. 70 °C / 158 °F

80W

Power driver and wiring

• To allow for variance in the installation, it is not recommended to load the power driver

beyond 90% of it’s rated maximum power

- Xitanium LED driver 20 W (logistic code 929000654006) max 18 W

- Xitanium LED driver 80 W (logistic code 929000653906) max 72 W

- Xitanium LED driver 75 W (logistic code 929000869713) max 70 W

• The maximum number of engines that can be connected depends

on the ambient temperature of the InteGrade engine in the application

(< 10 °C and > 10 °C / < 50 °F and > 50 °F)

• Use Philips InteGrade LED power cable of 1 m (39 inch) or 2.5 m (98 inch)

• If InteGrade power cables are extended, only use 0.75 mm2 (AWG 18) or

thicker cable uptil a length of max 10 m (32 feet) between driver and Philips LED power cable

• If you wish to make any other conguration, please contact Philips.

Parallel connection

• You can make any combination of 140 and 575 mm (6 and 23 inch) engines but:

- do not exceed the maximum total load on one driver and

- stay within the boundaries of the maximum load allowed for series connection,

see tables below!

The 20 W and 80 W driver

should be built-in.

Series connection with Xitanium 20 W driver

Xitanium 20 W driver

(logistic code 929000654006)

Maximum quantity of InteGrade engines

Engine wattage (watt) 12510

Engine Length (mm) 140 140 575 575

< 10 °C / < 50 °F 14 7 3 1

> 10 °C / > 50 °F 14 7 3 1

Series connection with Xitanium 75 W plug and play driver

Xitanium 75 W driver

(logistic code 929000869713)

Maximum quantity of InteGrade engines

Engine wattage (watt) 12510

Engine Length (mm) 140 140 575 575

< 10 °C / < 50 °F 30 15 8 4

> 10 °C / > 50 °F 45 20 12 5

Series connection with Xitanium 80 W driver

Xitanium 80 W driver

(logistic code 929000653906)

Maximum quantity of InteGrade engines

Engine wattage (watt) 12510

Engine Length (mm) 140 140 575 575

< 10 °C / < 50 °F 30 15 8 4

> 10 °C / > 50 °F 45 20 12 5

Philips LED

Power Driver

80 W 24V DC

0.75 mm2

(AWG 18)

max. 10 m

(32 feet)

driver cable

approx 0.3 m

(12 inch)

Philips InteGrade

cable per string

together max. 2.5 m

(98 inch)

Philips LED

Power Driver

20 W 24V DC

0.75 mm2

(AWG 18)

max. 10 m

(32 feet)

driver cable

approx 0.3 m

(12 inch)

Philips InteGrade

cable per string

together max. 2.5 m

(98 inch)

Example parallel connections (more strings) Example series connections (one string)

InteGrade LED engine 140 mm (6") InteGrade LED engine 575 mm (23") 1 string

Wiring diagram with Philips InteGrade LED engines

Form No. 3222 635 67102 US -30-+30

LE-6590-A 06/2013

www.philips.com/oem

www.philips.com/ledrefrigeration

www.philips.com/ledmodulesna / NA Customer Support/Technical Service: Tel. (1)800-372-3331

Table des matières

Autres manuels Philips Équipement d'éclairage

Philips

Philips StoreSet Linear SM504TI Manuel utilisateur

Philips

Philips VARI-Lite VL4000 Manuel utilisateur

Philips

Philips EasySmart InstantFit t8 Manuel utilisateur

Philips

Philips Lightolier Kubik 1.5 SL111A1 Manuel utilisateur

Philips

Philips RC095V Manuel utilisateur

Philips

Philips MasterColor CDM P-5970 Manuel utilisateur

Philips

Philips 33611/**/16 Manuel utilisateur

Philips

Philips Ecomoods 40339/**/16 Series Manuel utilisateur

Philips

Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Manuel utilisateur

Philips

Philips Ecomoods 57940/31/96 Manuel utilisateur

Philips

Philips L 1250 - HPM Instructions d'utilisation et d'entretien

Philips

Philips HP8550 Manuel utilisateur

Philips

Philips BN131C LED SWT/SCCT L600 PSU Slim Guide de l'utilisateur

Philips

Philips TT150 Guide de l'utilisateur

Philips

Philips hue Lightstrip Plus Manuel utilisateur

Philips

Philips WHS Manuel utilisateur

Philips

Philips ED-37 Manuel utilisateur

Philips

Philips Selecon Manuel utilisateur

Philips

Philips Hue 1822511 Manuel utilisateur

Philips

Philips CAX Series Manuel utilisateur

Philips

Philips ClearWay BGP303 Guide de l'utilisateur

Philips

Philips 56492-31-16 Manuel utilisateur

Philips

Philips B50 Manuel utilisateur

Philips

Philips CertaFlux RDL Vertical Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur