Philips RD6 Manuel utilisateur

HEAD SCREW

ROOF

LENS

GASKET

REFLECTOR

INTEGRATED

LED MODULE

CAUTION

1. WARNING : TURN POWER OFF BEFORE

INSTALLING OR PERFORMING ANY

MAINTENANCE ON THIS FIXTURE. Failure

to do so may result in severe injury

or death.

2. GFI PROTECTION! Fixtures which may

come in contact with or be exposed

to moisture (i.e. outdoors) shall

be installed on a GFI (Ground Fault

Interruptor) circuit. (120V only.)

3. The fixture should not be installed

in low lying areas or where water

may accumulate and stand for long

periods of time.

NOTE :

ROOF, OPTICS, AND LAMP STYLE WILL VARY WITH FIXTURE OPTIONS.

32000957, revision G

INSTALLATION INSTRUCTIONS:

6" BOLLARDS

MODEL NUMBERS: RD6, RF6,

AB04,AB06,LL-300, LL-301

page 1 of 2

SAFETY WARNING:

ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE

PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING!

This fixture can become very HOT! The fixture housing and lens, especially if it is glass, can become hot enough

to blister hands. Attention should be paid to where the fixture is mounted, particularly if it can be touched by

children or pets. To help prevent premature failure, decreased performance, overheating and risk of fire, keep

fixture and lens clean and free of leaves, mulch, debris and mineral deposits from water. The fixture and lens

can be cleaned using a soft cloth and a solution of mild liquid soap and warm water. Wipe clean and dry with a

soft, lint-free dry cloth. Avoid polishing fixture or lens.

This fixture is intended for installation in accordance with the National Electrical Code and local code

specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage

to the ballast and void the warranty. These instructions do not purport to cover all details or variations in

equipment, nor to provide for every possible contingency related to installation, operation, maintenance,

or mounting situation. Should specific problems occur that are not addressed by these instructions, contact

your Sales Representative or distributor for assistance. Retain these instructions for future reference.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS!

WARNING - Lamp gets HOT quickly! To reduce the risk of FIRE OR INJURY TO PERSONS:

Do not operate fixture with a missing or damaged lens/lens assembly.

Contact only switch or plug when turning fixture on or off. Do NOT touch hot lens or housing.

Turn off or unplug fixture and allow to cool before relamping. Keep lamp away from combustibles.

Do NOT touch lamp with bare hands at any time, use a soft cloth as oil from skin may damage lamp.

100 Craftway Dr.

Littlestown, Pennsylvania 17340-0128

Phone: 717-359-7131

SET SCREW

EXTRUSION

SUPPLY

TO LAMP

LED DRIVER

ASSEMBLY

SUPPLY

CONDUIT

(BY OTHERS)

GROUND

WIRE

LAMP

QUICK-

CONNECT

TWISTLOCK

BASEPLATE

ANCHOR

RODS

CONCRETE

SUPPORT

STANDARD FIXTURE STYLES

RD6

AB04

LL-300

RF6

AB06

LL-301

NOTE : FIXTURE STYLE AND BALLAST TYPE

WILL VARY WITH FIXTURE OPTIONS.

INSTALLATION

WARNING : Make sure the power is off before installing or servicing this fixture.

Install the anchor rods into a concrete footing as indicated on the supplied template. Install and level the

twistlock baseplate with ballast assembly as shown on the template.

Connect the supply lines from the supply conduit to the fixture's inputs. Tie the wires so they do not lie on the

ground. Connect the lamp supply quick-connect to the ballast quick-connect.

Set the fixture onto the twistlock baseplate such that the arrow on the baseplate lines up with the set screw.

Be sure not to crimp any wires in the twistlock.

Turn the fixture clockwise about 1/8 turn until hand tight. Tighten the set screw to lock it in place.

For fixtures that do not have an integrated LED module, install a lamp per the relamping instructions below.

Test the fixture for proper operation.

RELAMPING

Make sure power is off before relamping. Remove the head screw from the top of the roof and lift the roof off of

the fixture. Replace the lamp or install a new one per the label on the fixture. For LED fixtures, consult factory for

replacement modules or lamps. Replace the roof, checking to ensure the lens gasket is properly seated. Tighten

the head screw.

page 2 of 2

32000957, revision G

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips Équipement d'éclairage

Philips

Philips DL1 Manuel utilisateur

Philips

Philips Selecon PL3 LED Luminaires Mode d’emploi

Philips

Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Manuel utilisateur

Philips

Philips Ballasts For Fluorescent Lamps Manuel utilisateur

Philips

Philips 59510-17-16 Manuel utilisateur

Philips

Philips WHS Manuel utilisateur

Philips

Philips Bodine B426 Manuel utilisateur

Philips

Philips 56423-31-16 Manuel utilisateur

Philips

Philips EssentialWhite MR16 Manuel utilisateur

Philips

Philips hue Manuel utilisateur

Philips

Philips BVP528 Manuel utilisateur

Philips

Philips TrueLine SM530C Manuel utilisateur

Philips

Philips B50LP Manuel utilisateur

Philips

Philips hue 40801 Series Manuel utilisateur

Philips

Philips Day-Brite Manuel utilisateur

Philips

Philips ILS-CL-8RES Manuel utilisateur

Philips

Philips iColor Flex LMX gen2 Manuel utilisateur

Philips

Philips BN012C Guide de l'utilisateur

Philips

Philips BN012C Guide de l'utilisateur

Philips

Philips 17823/**/16 Manuel utilisateur

Philips

Philips SC Series Manuel utilisateur

Philips

Philips Lightolier Kubik 1.5 SL111A1 Manuel utilisateur

Philips

Philips Ecomoods 57940/31/96 Manuel utilisateur

Philips

Philips 57945-17-16 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur