Philips Hadco BUL16 MICRO BULLYTE Manuel utilisateur
1. The housing should not be installed in insulating materials such as bark, vermiculite, etc. for the full depth
of the housing. Surface use of these materials around BUT NOT ON TOP of the fixture is acceptable.
2. IMPORTANT: To prevent overheating, regularly check lens, keep it clean and free of debris such as dirt,
sand, leaves, mulch, etc.
3. The fixture should not be installed in low lying areas or where water may accumulate and stand for long
periods of time.
4. Do not install fixture within 10 feet (3.05 meters) of a pool, spa or fountain.
5. Use only with low voltage landscape lighting power supplies that are rated for a maximum of 25 amps, 15
volts per circuit.
Always turn fixture off, disconnect power and allow it to cool before performing any
maintenance, including relamping and cleaning. Failure to do so may result in severe
injury or death.
SAFETY WARNING:
Failure to do so will void warranty and could cause a fire.
CAUTION:
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING THIS FIXTURE.
Retain these instructions for future reference. Failure to follow instructions and codes will
void warranty, damage fixture and could result in injury.
THIS FIXTURE IS INTENDED FOR INSTALLATION IN ACCORDANCE WITH THE NATIONAL
ELECTRICAL CODE, STATE AND LOCAL CODE SPECIFICATIONS.
NOTICE:
(MAX)
50 W MR16
42 W MR16
35 W MR16
20 W MR16
MAY BEUSED IN THIS FIXTURE.
THE FOLLOWING LAMPS
Shroud
(See back for instructions)
To low voltage connector
to aim fixture
Loosen screw
Shroud screw
MR16 lamp
Heat Shield
Must always be in the UP
position.
32001444, revision C
100 Craftway, P.O. Box 128
Littlestown, Pennsylvania 17340-0128
Phone: 800-331-4185 Fax: 717-359-9672
INSTALLATION INSTRUCTIONS:
BUL16 MICRO BULLYTE
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.
page 1 of 3
STEP 1: Loosen the shroud screw and remove the shroud.
If the lamp is installed remove it as well. Then loosen
the (2) screws inside the housing.
STEP 2: Rotate the heat shield until it is on top of the lamp
assembly. This depends on how you will be mounting the
fixture. Once it is in the proper location tighten down
the (2) screws, replace the lamp and shroud and tighten
the shroud screw.
HEAT SHIELD INSTRUCTIONS
Depending on how the fixture is mounted you may need to adjust the placement of the heat shield.
The Heat Shield should always be on top of the lamp assembly. Failure to adjust the heat shield
properly may cause the outside of the fixture to become excessively hot and be a safety hazard for
the customer to touch.
INSTALLATION INSTRUCTIONS
1. Thread fixture onto ground mounted stake or box (not supplied).
6. Wire fixture following the directions for the Low Voltage Connector on the back of this page or hardwire
to low voltage cable.
2. Loosen shroud screw (see illustration above) and remove shroud.
3. Insert MR16 lamp (50 W MAX.) (not supplied) into socket.
4. Replace shroud, rotate to desired position, and tighten screw.
5. Loosen screw in arm, aim fixture to desired position, and tighten screw.
Loosen
(DO NOT REMOVE)
Shroud
Lamp
Shroud screw
Heat shield
page 2 of 3
32001444, revision C
screw
cover
supply cable
fixture cable
body
hot (ribbed)
common (smooth)
LOW VOLTAGE CABLE CONNECTOR INSTRUCTIONS
Low voltage cable connector to be used with 10 or 12 gauge supply cable and 18 gauge fixture cable. Hadco
recommends using SPT-3 water resistant (marked "WA", "W" or similar marking) supply cable such as our SCW500-10
or our SCW100-12. Hadco also recommends ordering the entire system, which includes the power console
(maximum 25 Amps, 15 Volts per circuit), fixture(s) (low voltage cable connector included) and supply cable to
ensure proper installation and operation.
When using our supply cable, it can be laid on top of the ground, placed under "ground cover" (that is, shallow
burial less than 6 inches or 15.2 cm deep), or directly buried in accordance with the NEC. If not using our cable, per
UL 1838-Standard for Low Voltage Landscape Lighting Systems, the secondary cable must be SPT-3 or suitable for
wet locations, sunlight resistant and direct burial per UL 493 and sized per UL 1838, and it must be buried less than 6
inches (15.2 cm).
Hadco recommends a minimum depth of 4 inches when burying in the lawn to prevent damage from aerators or
other lawn plugging equipment.
The 18 gauge fixture cable (provided with fixture) must be protected by routing in close proximity to the fixture or
secured to a building structure such as a house or deck. The fixture cable must be cut off so that it is connected to
the low voltage cable connector within 3 inches (7.6 cm) of the fixture or the building structure. When making an
underground connection to the 10 or 12 gauge supply cable (not provided), the fixture cable must not be buried
more than 3 inches (7.6 cm).
1. Connect the supply cable to the terminals on the power console (transformer) and turn ON.
2. Disassemble the connector by removing the Phillips head screw.
3. Inspect the connector to ensure the prongs are straight. If the prongs are bent, straighten with pliers.
4. Insert the end of the fixture cable into the square opening in the connector body. Bend wire over so that wire is
laying in the recess marked '18 GA'. This will help hold the wire in place while performing steps 5 and 6. Only 2-wire
cable is to be used and the common (smooth) wire and hot (ribbed) wires must be oriented as shown.
5. Press the supply cable into the recess marked '10,12/2 GA' on the connector body. Again the common (smooth)
wires and the hot (ribbed) wires must be oriented as shown.
6. Press the connector cover onto the connector body, making sure the screw holes line up with each other.
7. Assemble the connector by tightening the Phillips head screw. NOTE: Make sure the metal prongs in the
connector pierce all 4 wires; the fixture will light as the prongs pierce the wires.
page 3 of 3
32001444, revision C
Table des matières
Autres manuels Philips Équipement d'éclairage
Philips
Philips RS772B Manuel utilisateur
Philips
Philips VU6 Instructions d'installation
Philips
Philips Ballasts For Fluorescent Lamps Manuel utilisateur
Philips
Philips Lightolier EG1-4 Manuel utilisateur
Philips
Philips 56422-31-16 Manuel utilisateur
Philips
Philips bodine B30 Manuel utilisateur
Philips
Philips ELC/10H Long Life Manuel utilisateur
Philips
Philips Arcitone 57985/48/16 Manuel utilisateur
Philips
Philips 56459-17-16 Manuel utilisateur
Philips
Philips SL BAR 660 Mode d’emploi
Philips
Philips PLFRESNEL 1 LED LUMINAIRES Mode d’emploi
Philips
Philips TrueLine SM530C Manuel utilisateur
Philips
Philips Compac CTX6 Series Manuel utilisateur
Philips
Philips PLFRESNEL1 Manuel utilisateur
Philips
Philips BVP528 Manuel utilisateur
Philips
Philips Ecomoods 57930/**/16 Series Manuel utilisateur
Philips
Philips VL440 Spot Manuel utilisateur
Philips
Philips ColorBlast 6 Guide d'installation
Philips
Philips Ecomoods 40339/**/16 Series Manuel utilisateur
Philips
Philips burton SUPER EXAM 50 LED Fiche technique
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
