Philips VL72 Manuel utilisateur

OUT TO SUPPLY WIRES

SEE NOTE 3

STREET SIDE LABEL

SEE NOTE 5

POLE FASTENERS

SEE NOTES 2 & 6

INSTALLATION:

TURN POWER OFF.

2) Loosen pole fasteners on pod, if required.

3) Make fixture wiring connections to supply wires (by others)

- White to White

- Black to Black

- Green to Green

NOTE:

Both green ground wires from fixture should be

"bugged" together with incoming supply wire.

4) Slip luminaire post fitter onto pole and ensure wires

are not being pinched.

5) Orient by turning luminaire "street side" via label

supplied on globe fitter (pod).

6) Torque pole fasteners as follows to 7 ft. lbs.

CAUTION!

Over torquing of screws may lead to

damage or fatique of fastener.

7) Power to luminaire may now be turned on.

32002016, revision A

INSTALLATION INSTRUCTIONS:

VL71 & VL72

(Fixture)

SAFETY WARNING:

ALWAYS TURN FIXTURE OFF/DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

Ensure that the AC service is OFF before any installation or maintenance.

Do not switch service to ON until the entire installation is complete.

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone (US): 855-486-2216

Phone (CAN): 800-668-9008

TOOLS REQUIRED:

-5/32" Allen Wrench/Driver

-Torque Wrench capable of 7 ft. lbs. torque

This fixture is intended for installation in accordance with the National Electrical Code and local code

specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage to

the fixture components and void the warranty. These instructions do not purport to cover all details or vairations

in equipment, nor to provide for every possible contingency related to installation, operation, maintenance, or

mounting situation. Should specific problems occur that are not addressed by these instructions, contact your

Sales Representative or distributor for assistance. Retain these instructions for future reference.

POD

(EXISTING)

LOOSEN FASTENERS

TO REMOVE GLOBE

(EXISTING)

CAMDEN ADAPTER

(NEW)

1/4-20 SCREWS

(NEW)

ECOSWAP ASSY

(NEW)

INSTALLATION:

TURN POWER OFF.

2) Loosen, but do not remove (4) globe fasteners on pod.

3) Lift globe from fixture.

4) Remove existing ballast assembly.

- Push spring clip to release ballast module, twist ballast

module counter-clockwise, and lift to remove.

- Disconnect blue power quick disconnect.

5) Remove ballast assembly ring by removing existing screws.

6) Remove terminal block and bracket (if applicable)

7) Assemble Ecoswap to camden adapter by twisting

clockwise until spring clip snaps into place.

8) Make proper wiring connections.

NOTE:

In many cases, you may need to remove existing

blue power disconnect to "bug" wires.

9) Install entire unit onto fixture with (2) 1/4-20 screws while

ensuring wires are not being pinched.

NOTE:

For Type 3 distribution modules, rotate to orient

"Street Side (SS)" identification located on

Ecoswap, toward street.

10) Carefully lower globe onto fixture.

11) Tighten (4) globe fasteners to secure globe.

REFERENCE:

Please see enclosed Power Selection drawing

to adjust wattage output of Ecoswap module.

32002016, revision A

INSTALLATION INSTRUCTIONS:

V71 & V72

(Retrofit)

SAFETY WARNING:

ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW

TO COOL BEFORE PERFORMING ANY MAINTENANCE

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone (US): 855-486-2216

Phone (CAN): 800-668-9008

TOOLS REQUIRED:

-1/2" Socket/Driver

-5/32" Allen Wrench/Driver

-Philips Head Screw Driver

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips Luminaire

Philips

Philips 1001FR Manuel utilisateur

Philips

Philips Selecon SPX series Manuel utilisateur

Philips

Philips LUMINAIRES TRACK SYSTEM MINI HID CYLINDERS Manuel utilisateur

Philips

Philips Lightoiler Alter Concept SR T5 Manuel utilisateur

Philips

Philips Lytespan 83B70E Manuel utilisateur

Philips

Philips 6910860PU Manuel

Philips

Philips Tangent FXS Manuel utilisateur

Philips

Philips 6910835PU Manuel

Philips

Philips Calculite IS-PE Manuel utilisateur

Philips

Philips 38011/**/16 Manuel utilisateur

Philips

Philips Calculite 8044 Manuel utilisateur

Philips

Philips 33609-11-16 Manuel utilisateur

Philips

Philips HF3650 Manuel utilisateur

Philips

Philips PTS7-1 Manuel utilisateur

Philips

Philips PTS5-1 Manuel utilisateur

Philips

Philips SL111A2 Manuel utilisateur

Philips

Philips CTS3-4 Manuel utilisateur

Philips

Philips EG1-6 Manuel utilisateur

Philips

Philips ProSpec 37107 Manuel utilisateur

Philips

Philips XP Series Manuel utilisateur

Philips

Philips C4T4W Manuel utilisateur

Philips

Philips 34020/**/16 Manuel utilisateur

Philips

Philips SL205A Manuel utilisateur

Philips

Philips Lytespan 23S20MR Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur

ArtFox

ArtFox Beam 15R extreme Manuel utilisateur